Search Documents

By G. C. Bernard, L. W. Bernard, L. W. Holm, W. L. Jacobs

The effect of loam on the permeability of porous media to water was studied as a {unction of foaming agent concentration, specific permeability, pressure gradient, length of a porous medium and its oil saturation. At a given fluid saturation in a porous medium, the permeability to water was found to be the same whether loam was present or not. Foam decreases the permeability to water by developing a higher trapped gas saturation than that obtained by water flooding without loam present, increasing the concentration of foaming agent increased the trapped gas saturation and thereby decreased the permeability to water. The presence of oil reduced the capability of most foaming agents to decrease the permeability of a porous medium to water. A few surfactants were found to be effective loaming agents even in the presence of oil. These results are similar to those reported in a previous paper on the effect of loam on the permeability of porous media to gas. The effect of loam was found to persist in long porous media at moderately high reservoir temperatures and during the passage of many pore volumes of surfactant-free water. INTRODUCTION This paper describes part of a study on a novel approach in the use of surfactants for oil recovery; the use of foam rather than water to displace oil. Previously it was found that foam can displace oil which normally is not displaced by water.4 The foam is formed by successively injecting a suitable surfactant solution and gas into a porous medium. Foam appears to have at least two uses in the field: (1) it shows promise as a superior oil recovery agent, and (2) it shows promise as a selective permeability reducing agent. Foam may be very useful in water floods, or in other oil recovery processes, where highly permeable streaks or unfavorable mobility ratios are a problem. A previous paper reported the effect of foam on the permeability of porous media to gas.1 In the present study the effect of foam on the permeability of porous media to water is reported. The specific objectives of the study were to determine: (1) the effect of foam on the permeability to water in porous media of various specific permeabilities, (2) the effect of foam on the permeability to water in the presence of oil, (3) the effect of foam and crude oil on the trapped gas saturation, (4) the effect of foam on permeability to water at trapped gas saturation, (5) the effect of pressure gradient on the permeability to water under foaming conditions, (6) the persistence of foam during the passage of surfactant-free water through the porous medium, and (7) the effect of various foaming agents, length of the porous medium and temperature on the permeability reduction caused by foam. EXPERIMENTAL PROCEDURES EQUIPMENT AND MATERIALS The experimental apparatus consisted of consolidated and unco n soli dated porous media, wet test meters and constant delivery pumps. The porous media consisted of consolidated sandstone cores (6 to 36 in. long), and unconsolidated sand packs (3 to 30 ft long). The consolidated cores had permeabilities of 32 and 1,000 md and porosities of about 20 per cent. The sand packs had permeabilities of 3,500 to 211,000 md and porosities of about 40 per cent. (Throughout this report a term such as 100 md sand" is used. This term means that the porous medium had a dry, nitrogen permeability of 100 md.) Fluids used in the experiments were distilled water, 1 per cent NaCl solution, aqueous solutions of foaming agents, nitrogen gas, air and crude oil.

Jan 1, 1966

By M. R. J. Wyllie, Walter D. Rose

The use of electrical well logs for the quantitative determination of such reservoir parameters as connate water saturation, formation permeability and connate water salinity has recently been attracting the attention of a number of workers1,2,3,4,5. While the theory of the determination of connate water salinity from the self potential S.P. log has received rather detailed treatment, relatively little attention has been paid to the theoretical aspects involved in the quantitative interpretation of resistivity data. It is clear that if electrical well logs can be used for the quantitative evaluation of physical characteristics of reservoir rock, they will provide a valuable tool to supplement cheaply information obtained by more laborious core analysis. In certain cases it is conceivable that the coring program could be considerably curtailed if the electric log could be relied upon to give reasonably accurate quantitative information. It is our object in this paper to examine the theoretical basis of quantitative log interpretation as expressed in such well-established logging concepts as formation factor and cementation factor. It is also our object to investigate the physical aspects of the rela- tionship which is presumed to exist between resistivity index and brine saturation in reservoir rock. In particular, we will endeavor to draw attention to the fact that it is possible to express these logging concepts in terms of capillary pressure-saturation relationships, permeability and tortuosity, parameters which we will consider in this paper to be fundamentally indicative of rock texture. The probability of being able to obtain from log recordings alone the data theoretically essential to permit quantitative log interpretatiou will be examined, and consideration will also be given to the problem of formulating simple semi-empirical relationships for use in the field. THEORETICAL CONSIDERATIONS The concept of formation resistivity factor, or as it is now commonly called, formation factor, appears to have been introduced by G. E. Archie",". Formation resistivity factor as defined by Archie is the resistivity of a rock 100 per cent brine-saturated divided by the resistivity of the brine. This relationship had previously been used by physical chemists and the concept is, for example, implicit in an early treatment by Fricke7 of the conductivity of aqueous slurries. Archie was able to establish the fact that although the relationship between formation factor and porosity did not change too greatly for different rock textures, the relationship between formation factor and permeability was markedly dependent on rock texture. The relationship found by Archie between formation factor and porosity was expanded by H. Guyod8. Archie had suggested that the formation factor, F, could be expressed in terms of the porosity, F, as follows: F =F-m .... (11 where, F = effective porosity fraction of the sand, and, m = an exponent greater than about 1.3. Guyod introduced the term cementation factor for the exponent, m, since it may be qualitatively shown that formation factor for any given porosity tends to increase as the sand becomes more cemented. It would appear that the concept of m as an exponent representing the cementation in a sand is strictly only of qualitative value, since the quantitative estimation of m by means other than the determination of F and F has not been possible. Guyod suggests that m can be estimated from a visual examination of a sample of rock, but this method appears to be both arbitrary and unreliable. It can be said, however, that in intergranular reservoirs of practical interest, the range of m is from about 1.4 to 3.0. A possible explanation for the fact that m is found to lie between these limits will be offered below. The determination of formation factor is an essential preliminary to the

Jan 1, 1950

By W. W. Mullins

The development, by the mechanism of volume diffusion, of a grain boundary groove on an interface separating a solid phase and a saturated fluid phase is calculated under the following assumptions: 1) isotropy of the interfacial free energy 's, 2) applicability of the Gibbs-Thompson formula relating curvature and chemical potential, 3) a nearly planar groove surface. The groove profile is found to have a .fixed shape and linear dimensions that are proportional to (time)1/3. The constant of proportionality is evaluated and involves ?s in such a way that the latter my be evaluated from grooving kinetics. A grain boundary that intersects an interphase interface will tend to produce a groove along the line of intersection (Fig. 1). The ultimate motivation for the formation of the groove is the reduction in interfacial free energ that occurs as the grain boundary contracts. Smith has discussed the way in which the free energy of the interfaces determines their dihedral angles at the groove root and has given a detailed analysis of the effect of the dihedral angles upon the nature the microstructures developed in polyphase alloys. Herring2 has extended the considerations to the case in which the free energy of an interface depends on its orientation and has thus added torque terms to the condition for interface equilibrium. Although the grain boundary and the interphase interface may quickly achieve the proper equilibrium angles where they intersect, as determined by the balance of equivalent tensions and torques,"2 the groove will generally continue to grow (though with decreasing speed). Thermodynamically, this continued growth reflects the fact that the lowest free energy cannot be achieved until the entire grain boundary has been eliminated; mechanistically, the growth occurs in response to inhomogeneities of chemical potential that are caused by the constraint of fixed dihedral angles at the groove root. The latter point is illustrated in Fig. 1, which shows that atoms* near the groove are on the convex side of a cylindrically curved surface and therefore have a higher chemical potential than atoms on the flat interface beyond. Thus atoms tend to leave the curved groove shoulders and force the groove to deepen. When both phases are solid additional chemical potential gradient may arise from whatever strain fields are necessary to insure continuity of material across the interface. In the discussion that follows, this complication due to strain will not occur since we always assume one phase to be a fluid and the other a solid. The transport processes that may operate to permit growth of the groove are surface (interface)* diffusion, volume diffusion in the phase on either side of the interface, and evaporation-condensation when one phase is gaseous. (Also a melting-freezing process is responsible for groove enlargement on a solid-melt interface as discussed in Sec. VI). The theory of grain boundary grooving has been discussed in detail for the processes of surface diffusion and of one type of evaporation-condensation.3'4 The theoretical predictions for the mechanism of surface diffusion have been confirmed in an experimental study of grooving kinetics in copper.5 In this paper, the theory of groove development by volume diffusion will be presented. Volume diffusion can occur either by atomic migration in the solid S or by diffusion of S atoms in the fluid phase, or solvent, adjacent to the groove surface. As discussed in Sec. V, volume diffusion in the solid should be less important than surface diffusion in forming a groove. Apart from verifying this statement then, the main interest of the present analysis centers on diffusion in an external solvent. The solvent may be either a liquid (e.g., water, or-

Jan 1, 1961

News has just been received that Flight Commander William T. Hall, a Junior Member of-the Institute, was killed in action on Saturday, May 19, 1917. According to the' Toronto Star, Commander Hall was 24 years of age, a native of Toronto, and a grandson of the late William Kersteman. During the four years of his course in mining at the School of Practical Science, Toronto University, he passed every examination with honors. When war was first declared Commander Hall endeavored to join the artillery as an officer, and for that purpose secured a provisional lieu- tenancy with a Hamilton battery, but he did not receive an overseas appointment, and on being graduated as a mining engineer in 1915, he was offered a position in Chile, which he accepted. He left Toronto on May 27, 1915, and was engaged in Chile as a mining engineer for nearly a year. In the latter part of April, 1916, he decided to offer himself again for service at the front. He crossed the Andes and sailed for Liverpool, where he landed on May 13, 1916. On May 27, 1916, Capt. Hall was given a commission as lieutenant in the Royal Flying Corps. He went to the front on Sept. 1, 1916, and remained there continuously. On April 4, 1917, he was promoted from lieutenant to the rank of flight commander. No details of how Commander Hall came by his death have as yet been received.

Jan 1, 1918

By R. J. Teitel

The Pb-U system has been investigated by X-ray, thermal, and microscopic analyses. Two pyrophoric intermetallic compounds were found; UPb3 and UPb. The crystallographic structure of UPb3 is reported. A phase diagram was drawn for the system showing three eutectic and one syntectic reaction. AS a result of the interest in uranium metallurgy, the Pb-U system has been investigated. Practically no quantitative data appears in the literature concerning this system. Chips were machined from bars of high-purity uranium obtained from Ames Laboratory and the lead was 99.9 pct high-purity grade from Bel-mont Smelting & Refining Co. The chips were pickled in a dilute solution of nitric acid, washed in water and then alcohol, and dried prior to use for alloy preparation. The lead was simply sheared from the pig with no chemical treatment. Lead and uranium were placed in graphite crucibles and loaded into an induction furnace. In order to insure good alloy formation, the lead was loaded above the uranium to wash the uranium chips into the melt. After the charge was held at the desired preparation temperature for 15 to 30 min, it was allowed to cool in the crucible. The entire melting operation was accomplished in an atmosphere of helium (double charcoal refined grade with no further treatment). The procedure was to outgas the furnace by first evacuating it to 10-% m Hg, admitting helium to 8 psi gage and sealing the furnace off. An optical pyrometer focused on the charge through a hole in the crucible cover was employed for thermal measurements. Usually a 50° to 70°C correction had to be added to the instrument value. The most suitable alloy preparation temperature range was found between 1220° and 1280°C. The reason for this is explained by the phase diagram, Fig. 7. Above this temperature range two liquids separate preventing alloy formation upon cooling at a reasonable rate. On the other hand, below this range the uranium was coated with a layer of both compounds and the rate of reaction was diminished by diffusion processes. The fastest reaction rate occurred in this narrow range of temperature because only UPb coats the uranium and it evidently does not protect the uranium as well as UPb,. Apparatus and Procedures The development of apparatus and techniques was determined by the peculiar properties of the alloys. All the alloys were pyrophoric, and, consequently, the alloys had to be protected from oxidation by handling them in a dry box or inert atmosphere furnaces. Other operations performed outside of this equipment had to be done as quickly as possible. Thermal analyses were conducted in a furnace and arrangement similar to that described by the author.' Graphite crucibles having a thermocouple well in the bottom were used to contain the prepared alloy, while a helium atmosphere protected the melt from oxidation. The furnace was outgassed by pumping a 10-3 mm Hg vacuum until the furnace had been heated to 400°C. Then helium was admitted and the furnace sealed under 8 psi gage pressure. Chromel-alumel thermocouples were used for thermal analysis and the accuracy of thermal measurements was judged to be k 5°C. At first, an attempt was made to use platinum-platinum-rhodium thermocouples, but evidently lead vapors attack it at high temperatures forming low melting alloys. These lead vapors had direct access to the thermocouple because the graphite crucible was porous. A differential temperature control was used to regulate thermal analyses. The thermal gradient across an alundum tube placed between the windings and the crucible was maintained constant by a controller.

Jan 1, 1953

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) Members and guests who called at Institute headquarters during the period Jan. 10, 1917 to Feb. 10, 1917: Victor C. Alderson, Denver, Colo. G. Komar, New York, N. Y. Arthur W. Allen, New York, N. Y . H. H. Lauer, Allentown, Pa. George S. Blair, Pittsburgh, Pa. Frederick MacCoy, Antofagasta, Chile. F. J. Brulé, Toronto, Canada. E. P. Mathewson, Toronto, Canada. W. M. Corse, Buffalo, N. Y. Douglas Muir, San Antonio, Tex. John J Croston, Cullasaja, N.' C. F. W. Osborn, Ajo, Ariz. W. A. Deane, Waxhaw, N. C. Mortimer A. Sears, Washington, D. C. P. H. Dudley, New York N. Y. W. H. Selden, Jr., Iron River, Mich. J. D. Gilchrist, Denver, Colo. W. H. Staver, Yonkers, N. Y. L. Hoffman, Pottersville, N. J. Ralph H. Sweetser, Easton, Pa. Guy R. Johnson, Florence, Wis. Benjamin F. Tibby, Salt Lake City, Utah. W. McA. Johnson, Hartford, Conn. Carl J. Trauerman, Butte, Mont. John S. Kennedy, Philadelphia, Pa. H. C. Wilmot, Arequipa, Peru. D. C. Bard has become a member of the geological department of the Chicago, Milwaukee & St. Paul R. R., with headquarters at Seattle. Jay A. Carpenter has resigned his position as metallurgist for the West End Consolidated at Tonopah and has been appointed superintendent of flip. Nevada. Packard mines it Rochester.

Jan 3, 1917

February 18th, 1873. THE Institute assembled in the Hall of the Boston Natural History Society on Tuesday evening. Dr. T. Sterry Hunt, of the Boston Institute of Technology, after a brief address of welcome to the Institute, read an introductory paper on the Geognostical History of the Metals. President Raymond responded to the welcome of Dr. Hunt. The following names were then presented to the Institute, with the recommendation of the Council, for election Adams, J. M., - Silver City, Idaho. Daggett, Ellsworth, - Salt Lake City, Utah. Geist, Alfred W., - Boston, Mass. Hays, Dr. S. Dana, - Boston, Mass. Heinrich, Oswald J., - Midlothian, Va. Johnson, J., - Braidwood, Ill. Leckie, Robert G., - Actonvale, Canada. Lyman, Edward, - Troy, N. Y. Maltby, William, - Braidwood, Ill. Nichols, Lyman, Jr., - Boston, Mass. Ordway, Prof. J. M., - Boston, Mass. Rand, Theodore D., - Philadelphia, Pa. Richards, Prof. Robert H., - Boston, Mass. Rockwell, Prof. Alfred P., - Boston, Mass. Roepper, Charles W., - Bethlehem, Pa. Schulz, A. von, - Central City, Colorado. Singer, William F., - Pittsburgh, Pa. Spillsbury, E. G., - New York. Wells, Calvin, - Pittsburgh, Pa. The session concluded with the reading and discussion of a paper, by Henry Engelmann, On the Mines and Ores of the Little Cottonwood Canyon, Utah. The second session was held on Wednesday morning, when the following papers were presented; On the Midlothian Coal Mines, by Oswald J. Heinrich. On the Probable Existence of Microscopic Diamonds in California, by Prof. Benjamin Silliman.

Jan 1, 1873

By Willard S. Morse

Referring to Mr. Rickard's paper on " The Limitations of the Gold Stamp-Mill" (Trans., xxiii., 137), and the discussions that have followed, and without entering into any controversy as to the relative merits of the " California " and " Colorado " types of stamp-mills, I wish to give the results obtained on ores from Lynx Creek district, near Prescott, Arizona, with a stampmill of the Colorado, or, more precisely, the Gilpin county, Colo., type. The mines of the district have been worked for nearly thirty

Jan 1, 1896

By J. W. Axelson, J. N. S. Kwong, J. T. Adams, E. L. Pire, J. F. Johnson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental understanding of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1—the mechanism of the fracture process itself, 2— the particle size distribution of the crushed product, and 3—the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced. Fracture of Solids This phase of the crushing problem is the most fundamental because it is concerned with the actual mechanism of fracture. The main problems in a study of the fracture process are concerned with the questions of why and how fracture occurs and why there is such a discrepancy between the actual and theoretical energies needed in a fracture process. In considering the how of fracture, Poncelet40 carried Out experiments On the crushing of glass under compression. Actual photographs were taken of the glass plates in various stages of fracture-From these experiments Poncelet was able to postulate a probable mechanism of fracture. Probably because of the quantitative nature of the problem, considerable effort has been expended to find an explanation for the low tensile strength of materials and the conversely high energy for crushing. Tensile strengths are often only 1/500 of the theoretical while the energy for crushing is usually at least 500 times the theoretical. A review of the work to explain the low strength of glass is given by Weyl,52 in which the work of Griffith," Joffe,32 and Powell and Preston " are discussed. In a recent paper Seitz46 holds that the presence of flaws and fissures, as originally expounded by Griffith, is the most probable reason for the low strength of metals. Since a mass of data has been accumulated on the fracture strength of materials, several investigators have attempted to correlate this data in the form of an equation. Glathart and Preston," Taylor,40 Ponce-let,40 Machlin and Norwich," and Frederickson and Eyring,20 have all considered this problem, and the final relationship has always been that the stress for fracture is proportional to the logarithm of time. Murgatroyd30 arrived at a very similar relationship by a different method. The study of the fracture process has used many methods. Among some of these are the thermody-namic approach used by Furth21 which was based on the work of BornxL and later used by Saibel,43 and the statistical method applied by Fisher and Hollo-mon.10 In recent years metallurgists have concerned themselves with the problem of brittle .fracture as opposed to the usual plastic failure of metals. The great amount of interest shown is reflected by the number of contributors to the recent symposium on the fracture of metals.' Repeated failures of welded ships during World War II have accelerated these Studies.31,50,34 The shifting of thought from an emphasis on the

Jan 1, 1952

By J. A. Herbst, K. Rajamani, M. Siddique

This paper presents an investigation of the accuracy of population balance model predictions for ball mill scale-up. Experiments performed in 25.4 x 29.2 cm (10 x 11.5) batch mill are used to estimate linear grinding rate parameters that, in turn are scaled according to specific power draft to predict performance in 381 x 292 mm (15 x 11.5 in.) and 762 x 457 mm (30 x 18 in.) batch and continuous ball mills, respectively. Results are presented for wet and dry grinding of two homogeneous solids, limestone (soft) and quartz (hard), and one heterogeneous solid, a complex molybdenite ore. In all cases good agreement between predicted and experimental product size distributions was obtained.

Jan 1, 1983

The week of Sept. 22, will be a week of convocation of societies in Chicago with the exposition of Chemical industries. The American. Institute of Mining and Metallurgical Engineers will occupy the stage for most of the week, American Ceramic Society meets on Wednesday, the American Electrochemical Society on Thursday, Friday, and Saturday, and the Technical Association of Pulp and Paper Industry from Wednesday to Saturday. There will also be a symposium upon Safety in the Plant and Mine under the chairmanship of M. L. Leopold, Safety Engineer of the U. S. Bureau of Mines, and in the evening after this sleeting-which will occupy an entire afternoon-there will be shown a series of motion pictures of safety work in plant, field-and mine. The motion picture program will consist almost entirely of films now being made. Even in motion pictures, the Exposition is outstanding as the place of introduction to the public of the newest and most recent developments. Each improvement of the projectoscope in motion-picture projection has been reserved for first public demonstration at the Exposition. Mention cannot be made of the new exhibits that are engaged for the Exposition, other than to say that the electric furnace will be in operation. These will give, probably for the first time, men of science an opportunity to see and compare the various designs and judge them for the various work to which they are applicable.

Jan 8, 1919

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Pekka S. Särkkä

The method of interactive dimensioning is based on the computation of the loading-deformation curves caused by country rocks on the pillars with numerical methods. The comparable loading-deformation curves of pillars with different shapes are determined with small-scale model tests in a servo-controlled testing machine. The equilibrium points, i.e. the stability of the different pillar-country rock systems are determined by matching these curves adequately scaled. A case from a Finnish mine is presented together with the stoping results.

Jan 1, 1984

The Lornex mine is located in the Highland Valley area of British Columbia, Canada, one of the most,promising districts of low-grade porphyry-type copper mineralization in the world; Lornex is operated by Rio Algom Mines, Limited, a member of the Rio Tinto Zinc Group of London. Exploration from 1965 to 1968 disclosed an ore body of 293 million tons with a grade of 0.43% copper and 0. 14% molybdenum; this led to the decision to construct a 38,000 tpd operation, and production commenced in the fall of 1972. The ore is open-pit mined with 15 cu yd (11 5 m3 shovels, which load 100- and 200 -ton trucks. These trucks dump directly into a 60 in. by 89 in. Allis -Chalmers gyratory from two sides of the 14 ft 6 in. (4.42 m) deep dump pocket and across splitters mounted on the pocket sides. The unlined pocket would hold 1,000 tons level full. The crushedore discharges into a 300-ton surge hopper equipped with an automatic sonic level indicator to prevent over -filling. A 96 in. by 23 ft (2.44 m by 7 m) apron feeder delivers the ore from the surge hopper to a 72 in. (1.83 m) transfer belt equipped with a tramp iron metal detector. The transfer belt discharges to a 60 in. (1. 52 m) conveyor which conveys the ore about 3,000 ft (914 m) to the 475,000 ton ore storage pile located near the concentrator. Four 48 in. (1.22 m) pan feeders transfer the ore to the mill feed conveyors, which in turn supply the two 32 ft by 15 ft (9. 75 m by 4. 57 m) semi-autogenous mills, which easily accept the 10 in. (254 mm) product of the crusher. Each semi- autogenous mill is followed by a secondary ball mill. The unusually large open side setting of the crusher accounts for its 6,300 tph maximum capacity. Concentrator capacity is now 48,000 tpd. Eccentric removal is eased by the design of the door to the crushed ore pocket, which has the cart rails mounted on its outer surface and is lowered to a horizontal position in the pocket by an electric winch. The top of the door rests on wear bar covered concrete piers in the pocket. Another feature is a chute through the floor at the crusher base that extends into the crushed ore pocket. Dust and spills of ore on that floor during crusher repairs are easily swept into the crushed ore pocket. This feature is also used at Bougainville and Palabora and has been added to others after operation has commenced. The design follows the concrete rectangular box concept with four main service and maintenance levels shown in the sectional drawings, although a third additional section has been added at the maintenance

Jan 1, 1978

By J. Doig, A. A. Bauer, F. A. Rough

AN investigation of the phase relationships between the 6 phases of the uranium-molybdenum and uranium-titanium systems was conducted by studying alloys ranging in composition from uranium-31.5 at. pct Mo to uranium-34 at. pct Ti. A ternary cut showing these phase relationships is presented upon the basis of thermal-analysis data obtained and upon the basis of metallographic and X-ray examination of heat-treated and quenched specimens. Isothermal ternary sections, inferred from phase relationships determined between the two 6 phases, are presented for the uranium-molybdenum-titanium system. In the compositional range investigated, a y-ura-nium solid solution exists at elevated temperatures. At about 900°C the 6-U2Ti phase, with limited molybdenum solubility, forms. Epsilon, a molybdenum-titanium-rich solid solution appears at the same temperature and appears in all phase regions that exist below this temperature except in the terminal 6-phase regions. The y phase is stable to approximately 660°C in titanium-rich alloys; the y and 6-U,Ti phases decompose at this temperature to a uranium in a peritectoid reaction. The y phase in molybdenum-rich alloys of the ternary cut studied decomposes in an apparent eutectoid reaction, at about 593°C, to the 6-uranium-molyb-denum and a-uranium phases. The e phase while present, presumably plays a negligible role in these reactions. Titanium was found to markedly decrease the stability of retained y in these alloys. Age-hardening characteristics developed in titanium-contain ing uranium-molybdenum alloys quenched from 900°C and aged at 500°C are ascribed to decomposition of Y to the a and E phases. INTRODUCTION Alloys of uranium with molybdenum, titanium, and zirconium, respectively, are of great interest because of their potential use as reactor fuels. As a result, this interest extends to the constitution of these alloys, particularly in view of their uniqueness of constitution. In these systems, alone, among known uranium-alloy systems, an intermediate phase forms by direct decomposition of the high-temperature y-uranium phase. As a prelude to possible future alloy development, an investigation has been undertaken of the phase relationships that occur between the intermediate phases of these systems. These phase relationships have already been reported for the intermediate 6 phases of the uranium-zirconium and uranium-titanium systems.' The results of an investigation of the phase relationships between the 6 phases of the uranium-molybdenum and uranium-titanium systems are reported here. The phase relationships that occur in the binary systems pertinent to this investigation are shown in Fig. 1. Phase nomenclature appearing throughout this report is as shown in these diagrams; the crystal structure of the phase is given in Table I. EXPERIMENTAL PROCEDURE Alloys were cast and fabricated to flat plate. Specimens were heat treated and examined metal-

Jan 1, 1959

The Board of Directors has authorized the following offers of sets of back volumes of the Transactions, at considerably reduced prices, to Members, Libraries, and Scientific Societies Per Set. I. Five volumes, bound in half-morocco, from No. 36 (1906) to No. 40 (1910), . $20 II. Ten volumes, bound in half-morocco, from No. 31 (1902) to No. 40 (1910), including Mexican Volume, 35 III. Twenty volumes, bound in half-morocco, from No. 21 (1893) to No. 40 (1910), 50

Jan 4, 1913

By F. E. Buch

The smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The :smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pet moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pet oxide copper. The predominating minerals are chalco-cite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. General Description Flotation concentrate, containing 10 Pet moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and Spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which Prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been Set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1949

October 16th, 1872. THE Institute assembled on Wednesday evening at the Western University, and was called to order by President Raymond. Mr. James Park, Jr., of Pittsburgh, made the address of welcome, which was responded to by President Raymond. The Council reported the following names, with approval, for election Ashburner, William, - San Francisco, Cal. Asmus, George, - New York. Baillie, Nathaniel, - Uniontown, Pa. Bowie, A. J., Jr. - San Francisco, Cal. Brown, A. J., - Treasure City, Nev. Butler, J. G., Jr., - Youngstown, Ohio. Chamberlin, J. G., - Leetonia, Ohio. Clark, R. Neilson, - Canyon City, Colorado. Cornell, A. B., - Youngstown, Ohio. De Crano, E. G., - San Francisco, Cal. Engelmann, H., - Salt Lake City, Utah. Faber du Faur, A., - New York. Janin, Louis, Jr., - San Francisco, Cal. Johnson, George J., - Salt Lake City, Utah.. Kent, Joseph C., - Phillipsburgh, N. J. Kent, William St. G., - Phillipsburgh, N. J. Liebenau, Charles von, - Silver City, Idaho. McClintock, A. H., - Wilkes-Barre, Pa. Miller, Thomas N., - Pittsburgh, Pa. Millholland, James A., - Mount Savage, Md. Peters, Ed. D., Jr., - Dudley, Colorado. Reese, Jacob, - Pittsburgh; Pa. Schirmer, J. F. L., - Denver, Colorado. Smith, W. S., - Fairplay, Colorado. Stoelting, Hermann, - Georgetown, Colorado. Sweet, W. A., - Syracuse, N. Y. Tripple, Alexander, - New York. Van Arsdale, W. H., - Swansea, Cal. Willard, Dwight D., - Bordentown, N. J. The following resolution was then offered and passed Resolved, That gentlemen present, not members, be invited to take part in the discussions of the Institute at the various sessions of the present meeting.

Jan 1, 1873

By Y. Kondo, A. M. Gaudin

A combined method for sizing in the sub-micron range was developed using centrifugation and gamma emission. Its essential features are: 1) Centrifugation of suspended mineral in water carried out at 4°C where water has its maximal density and zero temperature gradient of density 2) Gamma activition of the sample suspension induced by irradiating it in a nuclear reactor prior to centrifugation 3) Measurement of the activity of a beam of suspension as it is sedimenting in the centrifuge, using a scintillation counter provided with a discriminator. Albite, the sodium feldspar, was used as feed to the comminution step, and the induced gamma activity of Na24 was measured. Dissolved sodium ion caused a a non-settling activity in the measurement. Other "noise" is due to scattered gamma radiation from albite particles in the centrifuge outside of the line of sight. These two activities were obtained sep arately and subtracted from the total activity counted. The relative solid concentration in the suspension under the collimating slit is proportional to this net activity. The cumulative weight per cent of undersize particles was calculated and plotted against size on logarithmic scales. The relationship was found to be linear down to about 30 mµ. The specific surfaces calculated from particle size distribution agree with those measured by krypton gas adsorption. The measurement of particle size distribution of comminution products has been of interest in clarifying the mechanism of the process. The Gaudin-Schuhmann equation1,2 relates the cumulative percentage undersize, y, to relative particle size x/k. The particle size, x, and the size modulus, k, together with the distribution modulus, m, characterize the particle size distribution, m is the slope of a plot of log (y) against log (x/k). This equation has been verified for ground particles down to 1 micron in size.3'4 For particle sizes smaller than a few microns, the precision and facility of sedimentation and microscope techniques become questionable. Use of a centrifuge which shortens settling time from weeks to hours is attractive. Many centrifugal methods have been proposed; however, determination of the solid concentration of the suspension at a reference level as a function of time is difficult, and sampling the suspension is likely to introduce errors. Measurement of particle size distribution by X-ray absorption in gravitational5 and in centrifugal6 sedimentation have also been tried. In these methods, the absorption coefficient for the solid is independent of size, since the wave lengths of the X-rays and gamma-rays are orders of magnitude smaller than the particles. Radiometric techniques7 in size distribution measurement have been developed within the last several years. They offer advantages over usual gravimetric and optical methods. PRINCIPLE OF METHOD The combined method of centrifugation and gamma emission for sizing in submicron range described in the present paper has the following essential features. 1) Centrifugation is carried out at 4 ± 0.1°C. Convection currents in the water phase due to density changes caused by temperature variation may disturb completely the settling system. To avoid this difficulty, the unique property of water having zero temperature gradient of density at 4°C is used. 2) Prior to size measurement the sample suspension is irradiated in a nuclear reactor and gamma activity induced. The gamma activity of the particles sedi-mented radially is measured by a scintillation counter provided with a discriminator. By this method, interruption of centrifugation by withdrawing samples is avoided and the counting rate at any time represents the solid concentration in the suspension at the level of the collimating slit of the centrifuge at the particular time at which the measurement is made. 3) By proper selection of the feed material and of the comminution device, gamma activities of foreign

Jan 1, 1964