Search Documents

By Arthur Braid

The war has caused an increasing scarcity of phosphorus and its well known alloys with copper and tin. At the same time, the production of brass and bronze, nickel-silver, cupro-nickel, and other non-ferrous alloys, has considerably increased. The manufacturers of these products had therefore to secure other materials which would serve their purpose; principally that of a deoxidizer, which could be obtained promptly and regularly. Fortunately these materials, pure carbon-free manganese metal and manganese-copper alloy, were not hard to find—in fact, they were never lost. Manganese in various forms has been used in Europe for more than a century; in this country, however, when manganese was first used, and indeed for a long time thereafter, it was consumed mainly in the manufacture of manganese-bronze. Many foundrymen at that time used manganese-copper with the same freedom as phosphor-copper. Although iron enters into the composition of certain grades of bronze, it is very detrimental to non-ferrous mixtures in general; consequently ferromanganese is not applicable, and therefore pure manganese metal, or the alloy of manganese and copper, technically free from iron and other impurities, is now being generally used. The following are the principal elements having an affinity for oxygen: 1, Sodium. 2, Potassium. 3, Calcium. 4, Strontium. 5, Barium. 6, Magnesium. 7, Aluminum, 8, Phosphorus. 9, Silicon. 10, Manganese. 11, Iron. 12, Zinc. 13, Lead. Each metal has its natural flux, or deoxidizer, in the form of a metal or non-metal which will alloy with it, and has a strong affinity for oxygen. For example, phosphorus, as is well known, acts very beneficially in copper alloys that contain tin. Within the last few years, and particularly since the war began, the .great value of mangancse in nickel alloys has been demonstrated, and one by one the manufacturers of these products have adopted its use. While manganese has not so strong an affinity for oxygen as magnesium, aluminum, or silicon, it is nevertheless sufficiently powerful to reduce any oxide of nickel, copper, or zinc that may be present in the nickel alloy to be purified.

Jan 1, 1919

By L. O. Howard

THE CHAIRMAN (WALTER DOUGLAS, New York, N. Y.).--I presume, gentlemen, that Mr. Howard's experience with the Great Falls basic-lined converter has been as regards the tonnage produced from a single lining, perhaps, a world's record. About 6 months ago Mr. Howard shut down and tore out what was left of the first basic-lining which was installed at the Old Dominion, the lining having produced something over 70,000,000 lb. of copper. This was due probably not only to the very excellent grade of the matte which was produced by the smelter there,

Jan 12, 1916

By S. H. Davis

THE pyrites used in making sulfuric acid in the United States have been largely imported from Spain and Canada, the Spanish imports amounting to nearly 1,000,000 tons per annum in the pre-war period. The greatly increased use of sulfuric acid and the cutting off of these Spanish imports, incident to war conditions, brought about a threatened shortage of sulfur supplies during the war period. The bituminous-coal mines of certain districts have, for many years, furnished a small tonnage of pyrite in the form of coal brasses. A mechanical concentrator at Danville, Ill., for a number of years, has been treating hand-picked lump pyrite and coal from the picking belt and from the mines and a small plant near Gillespie, Ill., for a few months has been recovering pyrite from washery refuse. Many mines throughout Illinois, Indiana, Western Kentucky, Ohio, and Pennsylvania have shipped an occasional car of the hand-cleaned lump pyrite. Only a very small percentage of the available pyrite has been recovered in this way, however, as usually the miners throw such lumps into the gob with slate and other impurities. It has been estimated that the western Indiana coal field could furnish more than 100,000 tons of pyrite per annum. The present production is very small. The possibility of furnishing the domestic trade with pyrites recovered as a byproduct from coal-mining operations appears attractive but there are certain features difficult to overcome. Pyrite, to be used in acid making, must meet with certain requirements as to size and purity. Lump ore for grate burners should be under 3 in. (7.6 cm.) and over 1 in. (2.5 cm.) in diameter. Fines for use in mecnanical roasters should be under quarter mesh. The material should be high in sulfur, free from arsenic and phosphorus, and as low in carbon as possible. The pyrite obtained from coal can be made to meet all the above requirements, but it is difficult to remove all the carbon. The pyrite in coal occurs as bands and nodules of varying thickness and size and of comparative purity, but mixed with this is more or less web sulfur. The web sulfur carries with it admixed coal, which may make the concen-

Jan 8, 1919

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral rutile. United States consumption of titanium dioxide in concentrates for these applications in 1982 was as follows: pigments, 630,000 st; titanium metal, 31,000 st; and welding rod coatings, 5,000 st. The only commercially important titanium ore minerals at the present time are ilmenite and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) stated that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlined the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during that time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, VA, and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, FL, for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for low-grade sands, led to a return of activities in this area. The large deposits near Tahawus, NY. were brought into production in 1942 by National Lead Co. (now NL Industries, Inc.), and by 1949 this company was the leading producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec. The large Trail Ridge sand deposit in Florida was discovered by E. I. du Pont de Nemours & Co., Inc. geologists in cooperation with the US

Jan 1, 1983

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By William E. Ford, Edward Salisbury Dana

Normal phosphoric acid is H3P04, and consequently normal phosphates have the formulas R3PO4, R3(P04)2 and RPO4, and similarly for the arsenates, etc. Only a comparatively small number of species conform to this simple formula. Most species contain more than one metallic element, and in the prominent Apatite Group the radical (CaF), (CaCI) or (PbCI) enters; in in the Wagnerite Group we have similarly (RF) or (ROH).

Jan 1, 1922

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By J.B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By J. B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By AIME AIME

ASIDE from the annual dinner-dance, the two outstanding social events of the Annual Meeting were the dinner- smoker on Monday night and the informal dance on Tuesday night, both of which were held at the Commodore Hotel. Approximately 400 attended the former event, compared with 570 a year ago, and about 250, people were attracted to the dance.

Jan 1, 1933

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants. IT must always be remembered, with regard to the problem of water-borne industrial wastes, that stream pollution from any cause is just one factor in the comprehensive problem of water supply in modern times. Industries nonexistent 25 years ago are now flourishing, and supplies of water piped to homes and apartments, as well as the greater number of plumbing fixtures per dwelling and per building, have created an ever growing demand on the country's water resources. Indication of this rapid growth in demand is shown in Table I, which is quoted from Abrams. of Texas increased 287% and the water consumption 7000 per cent." The domestic load varies greatly, depending on the extent of the available supply and the habits of the community. According to the report of the President's Water Resources Policy Commission' the United States Public Health Service reported a national average of 127 gal per capita per day, varying from 60 gal in communities of 500 persons to 140 or 150 gal in cities of 10,000 or over. Other critical areas may be cited to illustrate the inter-relation between new industrial processes and the demands for water in the area where the new enterprise is located. Powell and Wilson have pointed out that during World War 11, in the vicinity of Louisville, Ky., a rapid expansion of industry took place, consisting of numerous synthetic rubber plants. The demand for water increased from 37 million gal per day in 1937 to 62 million gal in 1943. These heavy requirements drew down the supply stored in the water-bearing aquifers to such an extent that urgent plans for recharging were considered. Similar situations have developed in the Los Angeles area and in the vicinity of Texas City. Warne4 has drawn attention to the situation in Los Angeles area, where in the West Basin the withdrawal of ground water in 1945 was 90,000 acre-ft, almost double the amount of the natural fresh water recharge. The draw down has been so severe that the level of the ground water is now below sea level, and sea water is invading the West Basin aquifers at rates up to 300 ft per year. In the Report of the Engineers Joint Council it is pointed out that in the area of Texas City the ground water table has been critically lowered. In 1930 the daily withdrawal from the water-bearing aquifer was 0.5 million gal. By 1945 the quantity withdrawn

Jan 1, 1954

By M. A. Steinberg, J. Wulff, R. Kamm

In a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described. In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. Circular-hole Grids and Analyses OF Radiographs Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in. centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1.125 in. in diam and the clearance between plungers and die wall was 0.001 in. The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value On an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1949

By Norris Johnston, Carrol M. Beeson

The gravimetric-vacuum distillation method was developed to permit rapid and accurate determinations of the oil-water ratios of small samples or sands containing little oil. In addition, the samples usually are so well cleaned and so little altered by the distillation at reduced pressure that rapid estimations of other physical properties may be made with the evacuated cores. Requiring only elementary glass-blowing technique, the distilling tubes and traps used in determining oil-water ratios were easily fashioned from the usual glassware. A sketch and description are given of the necessary apparatus, including the cylindrical electrical heaters. The procedure, requiring about 40 min., consists in raising the temperature and maintaining it between 675' and 725°F. for at least 10 min. while the pressure is held between I and 2 mm. Hg. The fluids condensed in the trap (cooled by a mixture of kerosine and solid carbon dioxide) are separated in a centrifuge and the volume of water is recorded. Determination of changes in weight with an analytical balance of all parts of the apparatus permits computation of weight of oil distilled and total weight of oil recovered. Introduction In determining the oil-water ratios of core samples, distillation at atmospheric pressurel-5 has proved to be sufficiently reliable for samples containing moderate quantities of oil. Since small samples and sands with little oil are encountered, how- ever, it appeared advisable to develop a method that would be applicable under these circumstances. Thegravimetric-extraction procedure1,6-9 undoubtedly is very reliable and could be used in all tests, but the time consumed in the determination would often delay field operations. This would be especially true when dealing with tight sands or viscous oils, both of which retard the extraction process. Accordingly, the gravimetric-vacuum distillation method was developed in order to combine the good features of both of the older methods; that is, accuracy and speed. By reducing the pressure, it was found possible to perform the distillation at a temperature that permits the use of glass apparatus, all parts of which can be weighed on an analytical balance. Thus, the fluids may be removed quickly from the core, the water is readily trapped and measured, and the loss in weight of the core is easily determined. In addition, the total weight of material condensed in the distilling tube and in the trap provides a method of determining the oil-water ratio that is practically independent of the one involving the loss in weight of the sample. The use of vacuum not only permits as much accuracy as does the gravimetric-extraction process, but it actually allows an increase in speed over the atmospheric-distillation method, because of the time required to cool the metal pots from about 1200°F. between runs. More important yet, the innovation makes possible the almost immediate reporting of permeability, and saturation, which is impossible

Jan 1, 1946

By Norris Johnston, Carrol M. Beeson

The gravimetric-vacuum distillation method was developed to permit rapid and accurate determinations of the oil-water ratios of small samples or sands containing little oil. In addition, the samples usually are so well cleaned and so little altered by the distillation at reduced pressure that rapid estimations of other physical properties may be made with the evacuated cores. Requiring only elementary glass-blowing technique, the distilling tubes and traps used in determining oil-water ratios were easily fashioned from the usual glassware. A sketch and description are given of the necessary apparatus, including the cylindrical electrical heaters. The procedure, requiring about 40 min., consists in raising the temperature and maintaining it between 675' and 725°F. for at least 10 min. while the pressure is held between I and 2 mm. Hg. The fluids condensed in the trap (cooled by a mixture of kerosine and solid carbon dioxide) are separated in a centrifuge and the volume of water is recorded. Determination of changes in weight with an analytical balance of all parts of the apparatus permits computation of weight of oil distilled and total weight of oil recovered. Introduction In determining the oil-water ratios of core samples, distillation at atmospheric pressurel-5 has proved to be sufficiently reliable for samples containing moderate quantities of oil. Since small samples and sands with little oil are encountered, how- ever, it appeared advisable to develop a method that would be applicable under these circumstances. Thegravimetric-extraction procedure1,6-9 undoubtedly is very reliable and could be used in all tests, but the time consumed in the determination would often delay field operations. This would be especially true when dealing with tight sands or viscous oils, both of which retard the extraction process. Accordingly, the gravimetric-vacuum distillation method was developed in order to combine the good features of both of the older methods; that is, accuracy and speed. By reducing the pressure, it was found possible to perform the distillation at a temperature that permits the use of glass apparatus, all parts of which can be weighed on an analytical balance. Thus, the fluids may be removed quickly from the core, the water is readily trapped and measured, and the loss in weight of the core is easily determined. In addition, the total weight of material condensed in the distilling tube and in the trap provides a method of determining the oil-water ratio that is practically independent of the one involving the loss in weight of the sample. The use of vacuum not only permits as much accuracy as does the gravimetric-extraction process, but it actually allows an increase in speed over the atmospheric-distillation method, because of the time required to cool the metal pots from about 1200°F. between runs. More important yet, the innovation makes possible the almost immediate reporting of permeability, and saturation, which is impossible

Jan 1, 1946

By R. W. Balluffi, B. H. Alexander

RELATIVE diffusion rates of copper and zinc in a brass have been measured in a vapor-solid type of couple with which the amounts of copper and zinc diffusing past inert Kirkendall markers can be obtained by means of a few simple experimental measurements. If inert markers are placed on the surface of copper which is then exposed to zinc vapor from a brass chips, the particles become buried due to outward diffusion of the copper, as shown in Fig. 1. A schematic diagram of such a couple after diffusion is shown in Fig. 2. Consideration of the diffusion flow of copper and zinc shows that the entire hatched area, including the cross-hatched area, is proportional to the amount of zinc diffused inward past the markers and that the smaller cross-hatched area is proportional to the amount of copper diffused outward past the markers. These areas are completely determined by the expansion of the couple, the depth of the buried particles below the surface, and the chemical composition at the specimen surface. As Darken1 has shown, the ratio of diffusivities of copper and zinc is then given by the ratio of these two areas. Polycrystalline copper and two copper single-crystals made by the Bridgman method were prepared in the form of 1.5 cm diam disks approximately 0.5 cm thick with faces plane and parallel. Tungsten particles approximately 0.001 cm in diam were bonded to the surface of each disk by heating 5 hr at 1060°C in vacuo. Each specimen was next

Jan 1, 1953

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By R. B. Hoy, Stanley J. LeFond, K. Reckling

Reported world production of natural diamonds approximates 40,000,000 carats a year (1980). The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, the Republic of South Africa third, and Botswana, fourth. Diamonds are also mined in South-West Africa (Namibia), Angola, Ghana, Sierra Leone, and other African countries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today it India, which was the first source of commercial production. In the US, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2,000 years ago, only about 260 tons have been mined. In order to obtain I g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential materials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamond in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (14/16 US mesh size). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite®, General Electric's Compax® and Stratapax® and Megadiamond's Megapax® have replaced natural diamond in turning tools, mining and oil drilling bits and dressing tool applications. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to modify light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem diamond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today.

Jan 1, 1983