Search Documents

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By Thornton D, Esterle J, La Rosa D

Control of blast fragmentation has a significant impact on coal mine profitability. Two approaches for the characterisation of coal blastability, particularly in terms of fines, are presented. Both approaches were implemented for the predictio

Jan 1, 1998

By Marois R, Hauff P, Kowalyczk P, Lipton G, Bedell R, Neville R, Edmundo G, Ehling M, Kern R

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the Short Wave Infrared range of the solar spectrum from 1220 to 2420nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a Quartz- Sericite-Pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

Reverse sensitivity is a critical issue for all extractive activities. Extractive industries can only establish in the location of the particular resource sought to be extracted. Avoiding a location near sensitive activities (such as residential activities) may, therefore, be more difficult for extractive industries, than for other industry (such as dairy factories).   This paper focuses on the following matters: +        principles to be derived from case law, +       district and regional council approaches managing reverse sensitivity effects, and +        avoiding, remedying or mitigating reverse sensitivity effects in the future.

Jan 1, 2006

By Sorokin M, Komkov A, Fyodorov A

The Vanyukov Process is a high-intensity smelting system that has been proven over the last 20 years for various metallurgical operations including the smelting of copper, nickel, copper-zinc, antimony concentrates, municipal waste treatment and pig-iron production. Extensive pilot plant tests on copper and copper-nickel concentrates have provided information for the design of the commercial furnaces. The thermodynamic analysis, design idea and the data obtained from commercial furnaces have shown that Vanyukov Process would be the best choice to smelt copper-nickel and nickel sulphide concentrates as well as oxide nickel ores.

Jan 1, 1996

By Van Barnefield J G

This paper is based on an evaluation project engaged upon jointly by Mount Isa Mines Limited nnd" IBM Austra]ia Limited. Mount Isa Mines Limited produces most of its copper from large underground open stopes within massive orebodies. Variations in the position and shapes of these stopes can result in improved metal recovery. An interactive graphics system has been developed to assist the mine design engineer optimise his design. The system can assist the engineer throughout the orebody visualis- ation, initial design and optimisation phases of his design. At any stage the engineer may call upon the display of gridded mesh data, digitized ore outlines or existing stopes or development (drives, cross-cuts). This information may be viewed in plan or any vertical section or in three dimensions with rotation. Tonnage and grade calculations may be quickly performed for initial stope outlines or for modifications to them during the optimisation phase. The system design is highly modular. An array of functions for the manipulation of coordinate and line information may be linked with the development or stope design functions in whichever way the designer desires.

Jan 1, 1977

By Nekitel S, Arumba J, Kopi G, Findlay RH

The Kainantu area lies within the composite Scrapland terrane which is composed of Mesozoic metamorphic and intrusive units, overlain by Cenozoic marine sediments, volcanic and intrus-ive units and Quaternary fluvial sedi-ments.Four deformations (Dl, D2, D3, D4) are recognised within the Mesozoic sequences, which consist of greenschist to amphibolite facies schist derived from felsic to intermediate pyroclastic rocks and pelitic sediments. The second, third and fourth fold events are present in the Cenozoic sequence, and these rocks are broken by thrusts related to northwest trending D3 folds. South-dipping, possibly lystric, normal faults are recognised and may be related to uplift and exposure of the metamorphic rocks as core complexes.Known mineralisation in the area consists of gold and copper skarn deposits, porphyry copper deposits, shear-hosted gold deposits, epithermal vein deposits and gold placer deposits. Over 35 hard rock and 18 gold placer deposits are known within the area. Of significance are the Kathnell shear-hosted auriferous quartz veins; such structurally controlled veins may be more widespread than proposed prev-iously and offer a new exploration target.

Jan 1, 1994

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Hatcher MI

Exploration undertaken at Copley diapir has located several occurrences of oxidized supergene and primary sulphide copper mineralization at the margin of the diapir or in adjacent country rocks. The mineraliza- tion is related to carbonate-rich epigenetic solutions which moved along major structural features closely associated with the intru sive diapir.

Jan 1, 1975

Mathematical modelling of continuous rotary vacuum filtration has been limited by the wide range of variables and the absence of connecting equations linking the variables. The filter type and size, mechanical design and predicted performance are generally determined by laboratory leaf tests on representative samples of slurry, or plant samples from an operating filter. A model has been developed which includes the major process variables such as slurry feed rate and concentration, cake thickness, wash water and air flow rates, to predict the filter production throughput, cake moisture and residual solubles. Where possible the model incorporates well established equations relating form filtration, washing and drying rates of the filter cake. Where an equation has not been formulated, standard curve fitting programs have been used to establish an algorithm. The theoretical equations and the derived algorithms are defined in the text. A major feature of the model is that operators, metallurgists, process, mechanical and instrumentation engineers become more aware of the interaction of process variables, the principles of the equipment design and its limitations when operating at peak performance. The model has specific application in the alumina industry where a high moisture content of the filter cake can increase chemical losses and energy costs, and in the coal industry where overseas companies are insisting on lower export coal moistures.

Jan 1, 1989

Pyrrhotite is the predominant gangue mineral at Renison comprising about 60 percent of the sulphides in an average ore blend. It exists as two crystal structures - monoclinic and hexagonal. Monoclinic pyrrhotite is the slowest floating of all minerals but is ferromagnetic and hence recoverable more efficiently by low intensity magnetic wet drum separators than flotation. This paper discusses the installation and commissioning of four 0.915 m x 3.0 m, 0.1 Tesla permanent magnet, wet drum separators prior to sulphide roughing flotation. Planned circuit and process control modifications to better accommodate magnetic separation into Renison's flowsheet will be Discussed.

Jan 1, 1991

By Pratt V, Davis K

Challenges facing middle management in the 1980's and beyond are not confined to business matters such as industrial relations, government and legal constraints, corporate takeovers, and commodity marketing. More particularly they deal with people issues and the interrelationship of corporate/ family relationships. There is a need for corporations to acknowledge the growing conflict between corporate/family roles being brought about by such matters as equal opportunity, double professional marriage partnerships, personal mobility and the increasing stress faced by managers as a result of current demands and expectations being placed on them. While the main responsibility for managing professional life as well as the relationship between professional and private life rests with the individual executive, corporations nevertheless have a major responsibility to assist these executives in this management process. Corporations in Australia are taking steps to address this situation but much more needs to be done. This was highlighted in the March 1985 "Middle Management" course with its associated Spouses Programme presented jointly by Australian Mineral Foundation and The Australian Administrative Staff College. Effective communication is at the heart of the matter but no amount of training on this subject will bear fruit unless there is an associated commitment by executives to improve the effectiveness of their communi- cation process both in their corporate and family roles.

Jan 1, 1986

By Leahy GJ, Wright DJ, Player RI

The operation of a one tonne submerged combustion pilot plant for the recovery of copper from anode furnace and converter slags is described and the effects of variables discussed. Using coal as reductant, copper levels of anode furnace slag were lowered to 1% or less, with batch times of approximately 120 minutes. Fluxing with limestone was required to produce a fluid slag at temperatures of 1200 - 1300¦C. For converter slags, reduction to 0.5% Cu or less was achieved in batch times of 35 minutes. The chemistry of the pyrometallurg- ical recovery of copper is briefly reviewed in relation.to copper recovery methods.

Jan 1, 1978

By J Pan, T Chun, D Zhu, Z Guo, J M. Young, T C. Ooi

With the rapid development of the Chinese steel industry, the strong demand for iron ores has led to huge imports of various iron ores from all over the world. As a relatively new force in the iron ore world and an important raw material supplier, Fortescue Metals Group (FMG) has achieved an annualised production rate of 100 Mt of iron ore fines. Typical blends were designed to simulate sinter blends employed in Chinese steel mills, and to determine sintering properties and metallurgical performance of blends comprising FMG Rocket fines in pilot sinter pot. It is shown that the sinter of typical blends comprising 15 - 20 per cent rocket fines possesses excellent sintering properties and metallurgical performance. With Rocket fines substitution for competitor ores in a typical customer mill blend comprising fully imported fines, the sinter productivity and tumble index increased from 1.45 t/m2h and 62.0 per cent to 1.54 t/m2h and 64.0 per cent, respectively, while attaining similar reducibility index and reduction degradation index at lower solid fuel consumption.CITATION:Zhu, D, Guo, Z, Ooi, T C, Chun, T, Pan, J and Young, J M, 2013. Sintering and metallurgical performance of blends comprising Fortescue Metals Group rocket fines, in Proceedings Iron Ore 2013 , pp 519-524 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M D. Goodz, Wright R. F

This paper highlights the importance of accurate observational technical reports compiled by Mining Geologists and Engineers. Before uncovering the original reports in July 1992, all previous investigations discounted returning to old mining areas on the belief that all operations were suspended because they were 'unpayable'. However, the detail of the original reports removed any doubt of the economic value of retrieving remnant ore.The important feature was that the description of 'unpayable' by GMA could be equated to 11.6 - 35 g/t over the history of the mine. On the basis of these reports the Morning Star mine has been re-opened.

Jan 1, 1993

A BRIEF account of the water-power potentialities of Tasmania is given, together with possible applications of the power commercially. A short history of the Waddamana development is then given, and the main works are described.WATER POWER POTENTIALITIESTasmania is an island of approximately 24,500 sq. miles area (exclusive of small islands). An area of 12,000 sq. miles is at an elevation of over 1000 ft. above sea-level, and of 2300 sq. miles at over 3000 ft. above sea-level. Average annual rainfall varies from' over 140 in. on West Coast to 20 in. on East Coast, and for the whole island averages 48.5 in. The total water-power available, based on conservative figures for run off and efficiency, is 6,000,000 b.h.p. Only a small percentage of this total will, under present conditions, and under likely conditions in the immediate future, be capable of being developed commercially.An extensive hydro-metric and water-power survey is at present being carried out in order to collect information concerning the most promising water-power schemes. Already 400,000 b.h.p. has been located in different proposals, and there is still a large area of very likely country along the West Coast which has not been investigated yet. Tasmania thus has very vast power potentialities, which, combined with good ports and communications and wonderful mineral and timber resources, should augur well for the establishment of the great key industries, particularly chemical and metallurgical.

Jan 1, 1923

Four data sets are required to put constraints on the tectonic evolution of the southern rim of the Pacific Ocean basinI . data bearing on the dispersal of the major Gondwanaland continental fragments and the birth of the Southern Ocean,2. data bearing on the interaction of the Pacific Ocean basin lithosphere with the South American, Antarctic, and Australasian continental masses,3. data bearing on.the evolution of the Scotia Sea floor, and 4. data bearing on the evolution of the various continents, microcontinents. and volcanic arcs.

Jan 1, 1990

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

The last decade has seen a very rapid development in TBM tunnelling. Some trends are purely technical or economical and others relate more to preferences of different interests. Power levels have more than doubled and thrust levels too. Shield machines are developed to be able to handle harder rock and the open TBMs are made more feasible for `difficult' rock. What is right and what is wrong is more a matter of opinion, but one thing is certain: TBMs now are a useful tool and no longer an experimental work-shop for the enthusiasts.This paper highlights some recent developments and indicates some probable future ones. A few features that have increased the open TBMs' ability to cope with ever harder rock and also to overcome problems with poor rock are discussed in detail, using the Atlas Copco JARVA Mk 27 -the most powerful TBM built so far - as a reference.

Jan 1, 1993