Search Documents

Chlorination of organic matter by direct injection of chlorine gas or hypochlorite has been investigated metallurgically worldwide with little understanding of the basic chemistry of the passivation mechanisms in- volved. In this paper, chlorination of carbon is attributed to oxidation-reduc- tions, resulting in surface halogenation of graphitic or amorphous carbon. It is proposed that chlorine and carbon interact to form thin coatings of chioro-carbon complexes that block the adsorption of gold cyanide com- plexes, thus passivating the gold adsorption sites of carbonaceous matter. Analytical, spectrographic, microscopic and electron-optical methods have been applied to demonstrate the proposed mechanism of chlorine-carbon bonding, as well as to evaluate the advantages and limitations of chlorination in the pretreatment of refractory carbonaceous gold ores.

Jan 1, 1991

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Pearce, M Barteaux, S Pearce

The prediction of how waste materials will evolve geochemically within waste storage facilities has been the subject of hundreds of thousands of hours researched by geoscientists globally. Despite the quantity of research there are a number of significant areas of uncertainty that remain as partially resolved issues. One of the most significant issues is the applicability of scaling laboratory test results to field conditions, and the use of laboratory data for predictive calculations to determine geochemical evolution of waste materials in the field. This issue has arisen predominantly as a result of the relative paucity of field monitoring data from waste rock storage facilities (WRSFs) and the fact that laboratory test methods are not typically linked to specific field conditions; rather they are based on generic standardised methods and designed primarily to simulate accelerated weathering conditions that do not relate to field conditions in a linear manner.To address these specific issues the authors have in the last two years made significant progress in the development and deployment of advanced field monitoring equipment within numerous WRSFs. O’Kane Consultants (OKC) has previously reported the findings from data collected from these monitoring installations in a number of papers presented throughout 2013–2014. This valuable site data has subsequently been used by OKC as the basis to design and engineer advanced customisable site-specific kinetic leach columns at OKC’s geochemistry research laboratory. These columns represent an important advancement in kinetic column assessment methodology as they have been designed to replicate the field internal conditions within waste facilities.Key features of the columns include their capacity, size and technical specifications; including fully programmable solenoid-controlled air supply with variable flow and pressure control and in-line heating option, automated temperature control and monitoring, automated oxygen consumption and carbon dioxide production monitoring, and soil moisture/matric suction monitoring.This flexibility of the design not only allows for more accurate field-based assessment of pyrite oxidation rates (POR) but also assessment of the potential effectiveness of waste management options such as deposition within a reduced oxygen environment, for example, as simulations of reduced net percolation rates or oxygen ingress rates can be accommodated.CITATION:Pearce, S, Pearce, J and Barteaux, M, 2015. Advanced customisable leach columns – a new kinetic testing method to simulate site-specific conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Misima Mines Pty Ltd (MMPL) operates a large open cut gold mine on Misima Island in the Louisiade Archipelago in Papua New Guinea. Misima Island lies approximately 600 km east-south-east of Port Moresby. The island is 40 km long by 10 km

Jan 1, 1994

By R Whittering, C Greet

High chrome grinding media has been used in the mining industry for quite some time, as it often proves economical on a wear basis. However, it is unusual for an operation to change to high chrome solely due to its metallurgical benefits. KagaraÆs Mount Garnet operation made the change from forged steel to high chrome media after laboratory testwork indicated that copper grades and recoveries would improve. The outcome was remarkable with positive changes in pulp chemistry throughout the circuit accompanied by marked improvements in copper, lead and zinc grades and recoveries. Reagent dosage rates were reduced, often by more than half, and the grinding media wear rate dropped to less than a third of the wear rate of the forged steel media. The economic analysis showed that out of the total increase of revenue and savings from metallurgical improvements and reagent and media consumption reductions the metallurgical improvements made up approximately 73 per cent, the reduced reagents saved 25 per cent and the savings through reduced media wear contributing by just over one per cent. This indicates that the popular view of high chrome media only being trialled in the plant for wear economics is outdated and the focus of operations should be shifted to using high chrome media for the metallurgical benefits.

Jan 1, 2006

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By G Harbort, D Clarke, D Morgan, C Sola

Northparkes Mines commenced production in 1994 and the mine has significant reserves to allow operation into the future. There are a number of potential future concentrator feed sources with variable sulfide mineralogy and grades.In February 2012 a comprehensive flotation survey was conducted to allow mass balancing and evaluate the operation of the flotation circuit. A rudimentary, copper element only, unsized flotation simulator was developed to evaluate high level potential for optimisation and improvement. In 2013 this flotation model was expanded to produce a mineral based, floatability component model to estimate the effect of future concentrator feed source on metallurgical performance. This revised model allows various circuit configurations to be simulated to provide a high level blueprint for the long-term planning to maximise performance.This paper provides a review of the process followed to develop the model, including an analysis into the mineral floatability component model and its calibration against plant operations. The effect of varying feed mineralogy and feed quality on future performance has allowed an internal review of potential circuit changes needed to accommodate the changing future feed.CITATION:Clarke, D, Harbort, G, Morgan, D and Sola, C, 2014. Northparkes Mines – flotation and planning for the future, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 203–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984

By H Arvidson, J Vann

When only wide-spaced drilling is available, for example at concept, prefeasibility and feasibility stages, properly implemented linear estimation (including ordinary kriging) predicts grade tonnage relationships that are over-smoothed compared to final production estimates (and production). Non-linear estimation and conditional simulation are alternative geostatistical approaches that can provide more reliable estimates of the recoverable tonnage and grade from wide-spaced drilling. Non-linear estimation and conditional simulation have been rarely used on iron ore deposits. However, these techniques have had wide application in other commodities such as gold and base metals. Conditional simulation has been used in the iron ore industry (eg Guibal et al, 1997); however, its use here is outlined as a means of generating non-linear estimates, not just its use for variability and drill spacing analysis. As a rule, regardless of commodity, the decision to use non-linear geostatistics will necessitate increased skills and require more time. This decision must therefore be justified in terms of cost-benefit. Such cost-benefit analysis is not straightforward, and to help an approach for determining when linear estimates are inadequate is presented. Recommend in this paper is a well-established non-linear geostatistical approach, the global ædiscrete Gaussian modelÆ (DGM) of change of support, as a tool to establish whether moving from linear to non-linear estimates will materially improve estimate results. Also discussed is the additional use of DGM as a block model validation tool. One specific factor contributing to the lack of application of non-linear geostatistical methods in iron is the added difficulties that arise when conditional simulation and non-linear estimates are required to reproduce the numerous and often important correlations between variables in iron ore deposits. Consequently, presented in the paper is a synoptic review of non-linear estimation and simulation methodologies applicable to correlated variables.

Jan 1, 2007

By D Thornton, B Smith, S Demey

Mine to Mill (MTM) optimisation, a total systems approach to the reduction of energy and cost in mining and mineral processing operations, is well-established technology. However, successful applications of MTM optimisation have been largely confined to gold, copper and lead/zinc semi autogenous grinding (SAG) operations, where the goals of tweaking the blast design to increase fines and hence throughput through the mill have been relatively easy to meet. The application of MTM optimisation in a more demanding environment, like that of a multi-stage crushing and screening aggregate operation, was conceived as part of a Department of Energy (DOE) initiative in 2004, aiming to reduce the energy consumption in the US aggregates industry. Two quarries operated by the Luck Stone Corporation of Richmond, Virginia, were selected for the demonstration sites. Dealing with ore variability and a requirement to maintain a fixed feed size distribution to the tertiary plant, whilst still aiming to increase yields of saleable products, presented some unique challenges. Despite these variables, the implementation of the MTM approach at Luck StoneÆs aggregate plant in Pittsboro, North Carolina, has led to a tangible improvement in productivity, particularly in the primary and secondary plants. The successful outcome was dependent upon several key factors, including reliable blasting and processing models, careful analysis of the rock conditions and plant configuration, understanding and buy-in from the Luck Stone operations staff, excellent collaboration with Virginia Tech staff and students, and long-term monitoring made possible through comprehensive PLC logging. This paper presents a review of the work conducted at the Pittsboro quarry and highlights the key reasons behind the successful implementation of the MTM approach in a complex plant environment.

Jan 1, 2007

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By J Caron, M Athayde, F Lavoie, R Joyce

Decarbonisation has become a major challenge for the global steelmaking industry, turning towards new technologies aimed at carbon footprint reduction, which on its own accounts for approximately 9 per cent global emissions. The iron and steel industry represents a ‘hard to abate’ sector, where much of efforts are currently being deployed into initiatives aiming to decarbonise the ironmaking through the use of green hydrogen, carbon capture utilisation and storage and state-of-the-art operation of current technologies, while little efforts being deployed to find carbon-efficient solution to iron ore burden preparation, where high-grade iron concentrate will increase in importance to ironmaking regardless of the chosen reduction route. Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), produces high-grade hematite concentrate with one of the lowest carbon global footprints. Still, QIO is partnering with its clients to the development of burden solutions to minimise CO2 emission, in the seek for a decarbonised steel. In a strong technological partnership, Binding Solutions Limited (BSL) has developed a novel, coldbinding technology to provide a cleaner, more cost-effective alternative to induration. The technology allows miners and steel producers to reduce Capex significantly and reduce energy consumption and CO2 emissions by 90 per cent. QIO and BSL have partnered to adapt the disruptive cold binding technology developed by BSL to QIO’s concentrate to produce a high-quality low emissions iron ore agglomerate. This paper describes the efforts taken to further develop BSL’s cold binding technology and its application to QIO’s high-grade iron ore concentrate to produce a hematite cold bonded briquette (hCBB) showing comparable performances with high quality seaborne fired pellets.

Nov 8, 2021

By S Gossmann, J Barlow, S Denner

"Unconventional gas resources, including coal seam gas (CSG) reservoirs, can be located above and below aquifers that provide groundwater for agricultural, industrial, urban and other uses. Development of these resources may, therefore, lead to potential impacts on groundwater supply.Management of reservoir/aquifer interconnections necessitates a program of focused data acquisition. For example, groundwater transfer from shallow aquifers to underlying CSG reservoirs may occur where CSG-containing units subcrop beneath shallow aquifers, possibly at significant distances from operating wells.Arrow Energy is undertaking studies of connectivity between aquifers including an investigation in collaboration with the Queensland Office of Groundwater Impact Assessment to evaluate connectivity between the Condamine Alluvium (CA) and CSG-containing Walloon Coal Measures (WCM).The Condamine Valley hosts highly productive agricultural land with groundwater resources heavily utilised for irrigation. Water demand outstrips available supply and groundwater has been subject to restrictions on further development since the early 1970s. Developments that could have an additional impact on groundwater resources in the CA are of major concern to local landholders. This paper describes: planned field investigations at two sites: 1. Stratheden, where pumping from the WCM will be undertaken 2. Daleglade, where pumping from the CA will occur how the data to be collected from field investigations will be used to refine predictions of flux between the CA and the WCM.CITATION:Denner, S, Gossmann, S and Barlow, J, 2013. Planned field investigation of connectivity between the Condamine Alluvium and Walloon Coal Measures, in Proceedings Water in Mining 2013, pp 91-98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By H Khoshrou, A Siamaki

Blast designs can have productive and non-productive impacts on downstream stages, mine productivity and operating costs. On the other hand, ground vibration, fragmentation, and back break caused by blasting impose damage and financial penalties and which must be controlled by blast design. One of the significant variables in blast design is the burden. In this study, the potentials of artificial neural network are investigated in prediction of burden in the Sungun copper open-pit mine. Input data were assembled through 18 blasting blocks according to different levels and experimental geomechanical investigation. To construct the model blastability index, uniaxial compression strength, hole diameter, specific weight of rock, rock quality designation and cohesion strength are taken as input parameters, whereas, burden is considered as an output parameter. Mean square error was used as the performance function and back propagation algorithm as the training function, containing four hidden layers and 14 data sets. Four sets of data were used to make sure that correct training had been carried out. This produced the coefficient correlation of 0.662.

Sep 26, 2011

The Kyaukpahto gold deposit is located at latitude 23¦ 47Æ 55" N and longitude 95¦ 56Æ 35" E in the Kawlin-Wuntho district, Sagaing Division, Myanmar. Gold mineralisation is hosted in sandstone of the Male Formation (Eocene) and occurs as stockworks and disseminations. The high-grade gold mineralisation is locally concentrated in a breccia zone. The gold deposit is closely associated with a NNE-SSW trending fracture system that forms tensional open fractures. These tensional zones are thought to be directly related to the Sagiang transfer fault system that experienced several hundred kilometres of northward dextral movement during the post-Upper Miocene. Major sulfide minerals are pyrite and arsenopyrite with minor galena, chalcopyrite and sphalerite. Gold mineralisation is associated with intense silicification, sericitisation and argillic alteration. Primary Type I fluid inclusions in the quartz from the mineralised zone are 5 to 15 ¦m across and yield homogenisation temperatures of 239¦ - 310¦C and salinities of 1.2 - 10.9 wt per cent NaCl equivalent. Laser Raman spectroscopic analysis indicates the presence of CO2 and CH4 in Type II fluid inclusions. Sulfur isotope analysis of disseminated pyrite in the ore zone by the laser ablation method indicates d34S values from -5.48ë to +5.53ë. The geology, alteration, ore mineralogy, fluid inclusion microthermometry and sulfur isotope data of the Kyaukpahto deposit are consistent with an epithermal ore deposit model for the deposit. However, the presence of CO2-liquid bearing fluids and the detectable CH4 in the gaseous phase of the fluid inclusions conflict with a typical epithermal origin for the Kyaukpahto deposit. The host siltstone and mudstone sequence, trace element geochemistry, and the disseminated nature of sulfide and gold mineralisation are also common characteristics of a sedimentary rock-hosted gold deposit, and these features may indicate a Carlin-like affinity. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

By B Davis, A H. Benzer, A N. Mainza, C M. Evertsson, L M. Tavares, M M. Hilden, M S. Powell, C Rule, G Asbj÷rnsson

The Mogalakwena North Concentrator of Anglo Platinum Operations was built with the capability to allow for future projected expansion. Several research groups, currently working with Anglo American on collaborative research over a range of projects, were brought in to review the existing operation, with a view to releasing some specific bottlenecks and providing specialist design input to the potential plant expansion.Based on a thorough review of the high pressure grinding rolls (HPGR) and crushing circuit, a wide range of de-bottlenecking opportunities were identified. This was followed by a series of surveys to provide performance measurements and to model the circuit in detail. From this effort a full simulation of the plant has been developed, including updated models of the HPGR, crusher, bins and screens. These models have been implemented in the researchersÆ Model Development Kit (MDK) version of JKSimMet, and in a prototype dynamic simulator based on the Matlab Simulink software.The observations, measurements and simulations have provided guidance and quantified the benefits of some proposed circuit modifications. Based on these findings a number of upgrades are being planned, with the aim of ensuring full utilisation of the installed equipment. The circuit demonstrates a potential expansion of over 30 per cent through minor improvements, and a 70 per cent increase in capacity with the addition of some strategic equipment.The HPGR-crushing upgrade project demonstrates the potential benefits of nurturing disparate Research groups into a strong inter-disciplinary technical team capable of supporting operational needs while developing future technology.CITATION:Powell, M S, Hilden, M M, Evertsson, C M, Asbj÷rnsson, G, Benzer, A H, Mainza, A N, Tavares, L M Davis, B, Plint, N and Rule, C, 2012. Optimisation opportunities for high pressure grinding rolls circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 81-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Haest, O Dominguez, D Mittrup

With the current focus in the mining industry on reducing costs, while simultaneously improving ore quality, infrared spectroscopy is a tool that can potentially assist companies to meet both challenges. Changes in the nature of infrared spectra are strongly influenced by changes in mineralogy, which is a key input variable for exploration (geology and orebody modelling and ore characterisation) and mining (pit design, mine scheduling and processing plant design/management).Infrared spectroscopic logging of drill holes has been embedded as a standard tool in BHP Billiton Iron Ore exploration, with a process set up to automatically deliver mineralogy and associated imagery to the end users (typically exploration geologists). The availability of consistent and automated mineralogy drill hole logs across a project is improving the output quality and reducing re-work.BHP Billiton Iron Ore is now looking into using the same infrared spectroscopic data for other applications, including improving predictions of geometallurgical and geotechnical parameters. Trials show that addition of infrared spectroscopic data to conventional data sets (element analysis and depth information) is significantly improving the accuracy of regression models to predict the lump-fine ratio.Further initiatives around infrared spectroscopic data in BHP Billiton Iron Ore include the installation of infrared spectroscopic sensors over conveyor belts, infrared spectroscopic mine face scanning and infrared spectroscopic blasthole logging. The ultimate vision is to have consistent, seamless mineralogical data from infrared spectroscopic sensing available throughout the mineral value chain (exploration/mining/processing). This seamless infrared spectroscopic data ‘bridge’ will allow the transfer of knowledge between the different sections of the value chain (exploration, mining and processing). For example, ore handle-ability could be predicted on exploration samples using regression models built from processing plant observations. In the opposite direction, information gathered about the buried stratigraphy by infrared spectroscopy utilised during exploration, could be used to predict the stratigraphy encountered during mining. This collaboration across BHP Billiton Iron Ore is expected to deliver significant savings, while improving the quality of the final product, thus helping to drive efficiency over the next decade.CITATION:Haest, M, Mittrup, D and Dominguez, O, 2015. Reaping the first fruits – infrared spectroscopy: the new standard tool in BHP Billiton Iron Ore Exploration, in Proceedings Iron Ore 2015, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Continuous, steady-state laboratory flotation tests showed that the recovery of cha1copyrite from a naturally occurring ore, under conditions closely resembling those of plant practice, could be expressed in terms of a first order rate equation.Tests on full-scale plant flotation cells, using impulse tracers, indicated ideal mixing of the pulp in the cells.It was demonstrated that values of first order flotation rate constants can onlv be obtained from conventional methods of analysis in special cases.Analysis of a plant sampling campaign by the author supported a first order kinetic equation for two mineral species, and for the individual size fractions of one of these.The effect of stage-addition of reagents is interpreted in kinetic terms.

Jan 1, 1966