Search Documents

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By B C. McLellan

The decline of ore grades on land, increasing demand and high prices for various minerals have led to an increased interest in mining the deep ocean sea floor. The potential deep ocean reserves are vast and in some circumstances the grades are high enough to consider mining. However, the consequences of such mining are as yet uncertain. This paper will present the results of a comparative assessment of life cycle impacts of deep ocean minerals. Two alternative extraction technologies from different deep ocean resource types were examined and key commodities are considered. Initial results indicate that the energy requirements will be higher than the average land-based resources, but may fall within the range of the deepest terrestrial mines.CITATION:McLellan, B C, 2015. Comparative life cycle impacts of deep ocean minerals and land-based counterparts, in Proceedings Third International Future Mining Conference, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Classification within the Inferred Resource category is based on geological judgement and the balance of extrapolation versus interpolation that the Competent Person is prepared to accept. These resources are typically drilled at spacings well in excess of the geostatistical range and at a density that is non-uniform. In many cases, a substantial proportion of the available data will be historical, and should be considered with more recent data sources. The provision of a robust geological model will increase the confidence in any resource estimate, and should be viewed as a critical component. The definition of Inferred Resources is of great importance to vein gold projects, since Indicated and Measured Resources generally require costly underground development for delineation. Indeed, many gold vein operations possess substantial quantities of Inferred Resources (>75 per cent) in their resource inventory both at project start-up and during production. This contribution explores a number of the key issues when using the Inferred Resource category and presents four recent case studies.

Jan 1, 2006

By R G. Moreby

The purpose of this paper is to provide the rationale for decision making when considering the use of three heading gate roads in Australian underground coal mines.There are currently 30 underground longwall mines in Australia with all but two employing two heading gate road longwall layouts. The volumetric capacity of these two heading ventilation circuits is evidently viable in typical block lengths and in low to moderate gas regimes. However, in gassier regimes, potential longwall production rates of 10 Mt/a, and or where block lengths are being extended to well beyond historical norms, a conventional two heading U circuit may not be adequate. Other than seam gas emission, block length and production dependent heat loads together sealed area management requirements also have to be considered.The two mines currently employing three heading gate roads have the opportunity to revert to two headings at any time but, based on operational experience to date, have not done so due to the consequential reduction in gas management capacity and lower production rates associated with gas delays and limitations on tailgate access.Although there are a number of alternative two heading longwall circuits available and employed worldwide, the custom and practice of promoting inert goaf atmospheres in most Australian coal mines to mitigate the risk of catastrophic gas explosions and spontaneous combustion often prevents the use of gas loaded bleeder systems. In this respect, Australian underground coal mines may be considered the safest in the world.The current situation is that three heading gate roads have been proven successful in Australian conditions, albeit at additional cost, where two heading ventilation circuits cannot manage net seam gas emission to the ventilation system at the production rates required. In this respect, a further important driver for decision making is the short to medium term value of CO2-e emission taxation in Australia.CITATION:Moreby, R G, 2013. The rationale for use of three heading gate roads in Australian underground coal mines, in Proceedings The Australian Mine Ventilation Conference , pp 13-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D Bradshaw, R Dunne, S Farrokhpay

It is well known that clays affect the flotation performance, and many of the refractory gold ores around the world contain clay minerals. Therefore, an ore sample from the Carlin Trend was selected for this study as these ores contain large quantities of clays. The presence of clay minerals in an ore makes it susceptible to a range of variables, such as the solution chemistry determined by pH and the chemistry of the rheology modifiers. The viscosity of the ore slurry was measured as a function of solid concentration and particle size distribution, in addition to using different rheology modifiers and pH regulators. The results were correlated with the ore flotation performance. It was found that various reagents known commonly as dispersants or rheology modifiers have different effects on the ore slurry viscosity. This study revealed that the gold flotation recovery can be improved by changing the pulp rheology.CITATION:Farrokhpay, S, Bradshaw, D and Dunne, R, 2013. Rheological investigation of the flotation performance of a high clay containing gold ore from Carlin Trend, in Proceedings World Gold 2013, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Yáñez, P Vallejos, R Grau, J Yianatos

In flotation cells, especially in large flotation units, froth management is a crucial variable that should be considered during the design phase or optimised to improve the performance of existing flotation circuits. This paper presents a simulation evaluation of the effect of launder design on the metallurgical performance of an industrial flotation circuit consisting of five TankCell® e630 (630 m3 ) cells in a Cu rougher duty. This analysis was carried out using a new industrial simulator, which was built on a wide database collected from many industrial concentrators. This tool is currently incorporated into HSC Chemistry® software and allows evaluation of the effect of launder design on mineral froth recovery, water recovery, entrainment, and other variables to be quantified. The industrial flotation circuit was evaluated under different launder design scenarios, considering an actual flotation circuit that includes TankCell® e630 cells for calibration and as a reference (baseline). Firstly, two different designs were evaluated in the full circuit: a standard launder design and a new launder technology. It was found that the new launder technology enabled improvement of the mineral recovery along the circuit, mainly for coarse particles, due to the improvement in froth mineral recovery. Next, the partial upgrade of the launder design along the circuit was analysed. Thus, the new launder technology was evaluated in the first and the last two cells of the bank. The results showed that upgrading the launders in different cells along the circuit delivered an increase in the final recovery with respect to the baseline, with a partial impact on the concentrate grade. However, these changes are less than those when evaluating the full upgrade scenario. A partial launder upgrade either in the first or last two cells of the bank showed similar final recoveries, but the latter enabled a slightly higher concentrate grade (about 1 per cent higher) to be achieved. Finally, the evaluation of launder design using the industrial simulator made it possible to estimate its effect on variables that are not commonly obtained from plant surveys, including froth recovery per particle size, collection recovery per particle size and liberation, gangue entrainment and bubble loading grade.

Aug 24, 2022

By C T. Dunbar, P A. Walker, G E. LeJuge

A programme of blast improvement was initiated at the Mt Whaleback iron ore mine by BHPIO management in early-1998. One component of that work was the need to improve wall control blasting practices to better achieve the designed pit slope elements. This paper describes the geological conditions in which pit walls are developed, the mine operating equipment, the blast design concepts applied to minimise blast damage, the techniques applied in an assessment of the blast performance and the operational procedures developed to ensure that the blast concepts are effectively implemented in the production environment. Substantial changes have been implemented in both technical and operational aspects of the mining operation in order to achieve the improvements in pit wall condition, in particular recognising the need for a more flexible approach to limits blasting in response to highly variable and complex geology. The benefits to the mine are not only an improved wall condition, but increased confidence on the part of mine management that mine plans may be implemented on design and on schedule.

Jan 1, 2001

By M I. Roberts

As Australia’s mining industry painfully retrenches, mining executives and managers strive to remain viable by seeking significant productivity increases directly through process improvement and indirectly by improving leadership and workplace culture, the most powerful determinant of productivity. Culture is the combination of people’s attitudes and behaviour, together with leadership values and focus.Comprehensive new and automated data collection and management systems promise much for improving productivity, yet despite rapid advances in measurement and sharing of data, the use of data can reduce productivity unless behavioural aspects are considered and designed as part of implementation. This is because systems drive behaviour that in turn shapes attitudes to determine culture.Experience from many mine sites and other industries in three countries confirm that the most powerful drivers of people’s behaviour are the Measurement-Analysis-Reporting system and business leadership.This paper discusses fundamentals of practical, statistically valid process measurement, analysis and reporting systems before discussing associated leadership considerations for sustained improvement in safety, productivity, employee retention, leadership, accountability and commercial returns.The key to productivity improvement is improving core processes and important support processes. In turn, the key to process improvement is identifying the major process components and their interaction by measuring and then analysing their variation and level of performance. Understanding variation is often neglected yet is usually highly significant. It is essential that the fundamentals of statistically valid yet practical process and data analysis are understood and incorporated into system design to ensure productive, informed behaviour.The design and use of Measurement-Analysis-Reporting systems influences behaviour most profoundly and determines people’s effectiveness. Behavioural aspects are detailed by focusing on six primary drivers of human behaviour and five basic systems for managing businesses. These are integrated in a seven-step process and productivity improvement methodology that combines statistical, analytical, systems and behavioural factors.The paper includes development, implementation and tracking of a project plan for improving management and leadership systems to drive aligned behaviours. This key leadership responsibility is essential for improving performance to get the most from capital while providing people with the opportunity to develop greater autonomy, which is essential for self-discipline, responsibility, initiative and accountability.CITATION:Roberts, M I, 2015. Integrating measurement, systems and leadership to build safe, productive cultures, in Proceedings Third International Future Mining Conference, pp 73–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By J Ashford, Minniakhmetov

Geostatistical simulations are the best practice for uncertainty quantification in non-linear systems. Simulations are currently undertaken on an ad hoc basis in the mining industry due to high requirements in computing environments and advanced geostatistics. In contrast to the estimation process, multivariate simulations can be performed using different methods, tools, and computational environments, similar to data science. For large companies with multiple commodities it is important to have a standard framework to test, build, and run workflows using different methods, applications and computational environments. This work presents an auditable, modular and scalable framework to create geostatistical simulation workflows where the workflow is abstracted from the implementation. Key aspects: automation – workflows should be able to run automatically given updated data (if hands on modelling is not required); auditability – workflows should document key considerations and parameters; modularisation – workflows should permit swapping out components, for example substituting domaining in Leapfrog software with automated domaining using machine learning scripts; scalability – easy, repeatable, portable deployments on diverse infrastructure (for example, experimenting on a laptop, then moving to an on premise cluster or to the Cloud); reproducibility – parameters should be archived to permit re-running and reproduction of workflows in future years; and sensitivity analysis – any component of a workflow should be able to run with multiple scenarios of parameters and data to enable global uncertainty quantification and sensitivity analysis. The presented framework can be used to create different workflows for geostatistical simulations in multiple assets to quantify uncertainty in the value chain for resource categorisation, reserves uncertainty, value of information and robust mine planning amongst others.

Mar 22, 2022

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s Ø6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s Ø6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By N Kawashima, R St C Smart, A M. Robertson

This paper focuses on a case study at a base metal mine located in a tropical semi-arid area of Western Australia (WA). It is demonstrated that understanding the geochemical nature of the mine tailings forms an integral part of innovative management strategies developed throughout the life-of-mine (LOM) when planning for mine closure. The tailings are currently stored at an above-ground valley fill tailings storage facility (TSF) and one option for long-term management under consideration is leaving the tailings in situ at mine closure and covering using the concept of an enhanced æstore and releaseÆ cover system.Extensive geochemical and mineralogical studies have found that the geochemical behaviour of the tailings in the TSF is significantly more benign than initially predicted. The sulfide content of the tailings is primarily pyrrhotite, which can be acid-forming, acid-neutral or acid-consuming depending on a number of factors including redox conditions. Tailings pore water at depth is pH neutral with excess alkalinity, low concentrations of dissolved metals and elevated sulfate concentration.Recent geochemical tests on tailings samples indicate that a reduction in the acid potential and a corresponding increase in the neutralising potential of the tailings, through partial removal of pyrrhotite at the ore processing stage, has the potential to further reduce the long-term risk of potential impact to the environment from any TSF seepage. The current work program investigates whether partial removal of pyrrhotite is feasible and secondly, whether this approach is necessary to produce a significantly better outcome at mine closure.CITATION:Robertson, A M, Kawashima, N, Smart, R St C and Schumann, R, 2012. Understanding tailings geochemistry - Continuous learning and innovation when planning for mine closure, in Proceedings Life-of-Mine 2012 , pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6 g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

By K C. Runge, E Tabosa, A Jankovic

Flotation recovery in geometallurgical modelling is usually predicted based on relationships developed from batch flotation testing of different ore types. These batch flotation tests are usually performed at a constant set of operating conditions and at a fixed feed grind size P80. Usually the laboratory feed grind P80 is that which is expected to be produced in the full-scale flotation circuit for that particular ore type.Flotation recovery will be a strong function of the valuable mineral particle size distribution, with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation of this fraction. This valuable mineral particle size distribution is not characterised by the solids P80 parameter alone. The proportion of material in each class will also be a function of the slope of the size distribution and the degree of preferential grinding of the valuable mineral in comparison to the total mass of the ore.This paper will demonstrate (through example) how these other size distribution parameters can change with a change in grinding technology, the size and operating conditions used in a grinding unit and the characteristics of the classification technology used in conjunction with the grinding unit. Case studies will be presented that demonstrate how this can result in these parameters being very different in laboratory testing to that produced in the full-scale comminution circuit. A rule of thumb that laboratory rod milling rather than ball milling produces a size distribution most similar to that of the full-scale grinding circuit will be challenged. These differences can result in a significant change in flotation recovery. It is therefore important to consider these parameters when developing a laboratory geometallurgical program, to enable more accurate prediction of the flotation recoveries that will be achieved in the full-scale process.CITATION:Runge, K C, Tabosa, E and Jankovic, A, 2013. Particle size distribution effects that should be considered when performing flotation geometallurgical testing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 335-344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Mills JC, Belcher CB

X-ray fluorescence spectrometry is used videly for routine quality control of the mining, )lending and agglomeration of iron ores. Most )f the procedures used, cannot tolerate significant changes in matrix composition or be Lpplied to a wide range of elements. Accord- ngly, a graphite briquette technique which is Lpplicable to some fifty elements in widely Tarying iron ore matrices is described. The ignificant advantages are suitability of the ame preparation for both optical emission and -ray spectrometry, a complete elemental overage for the range 5bcg/g to 100%, and the recision and accuracy of the methods are om.parable with the standard chemical.methods hich have been superseded in the authors' boratories. The proposed methods become ore attractive and economical as more prehensive information is sought.

Jan 1, 1975

By A Parbhakar-Fox, B G. Lottermoser, N Fox

"Determining the deportment of economic and environmentally significant elements in sulfidic mine materials (eg ore, gangue and waste) requires the use of advanced microanalytical techniques, including electron microprobe analysis (EMPA) and laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Sulfidic boulders were sampled from an acid rock drainage impacted ephemeral stream adjacent to historical copper-silver workings at Baal Gammon, northern Queensland. The abundance and deportment of a range of trace elements and precious metals were analysed in these samples. Whilst many of these elements represent a potential environmental risk if leached from sulfidic rocks into streams in the surficial environment, significantly some of these elements (eg In, Sb and Co) represent specialised metals that are currently considered to be in critical supply.Sulfidic waste rock material at Baal Gammon is dominated by chalcopyrite, arsenopyrite, pyrrhotite and pyrite. Microanalytical investigations revealed that chalcopyrite contains significant quantities of In, Sn, Ag and Zn either substituted directly into the crystal lattice or occurring as discrete sphalerite and stannite inclusions. Arsenopyrite, which may comprise more than 50 per cent of some boulders, is notably enriched in Sb, Co and Ni but also contains inclusions of sphalerite, chalcopyrite and stannite. In contrast, pyrrhotite contains no trace elements of economic significance, but instead represents a likely contributor to acid generation during oxidation in the surficial environment. Trace metals (eg In, Sb, Co, Ni, Zn) are liberated during sulfide oxidation of these boulders in the surficial environment, generating a metal-rich, low-pH leachate.Fe-oxides precipitated as rinds on the surface of these boulders under low pH conditions also contain abundant As, Bi, Sn, Cu and Zn. Abandoned or historical mines represent potential sources of metalliferous drainage that poses potential environmental risks to water and habitats. However, sulfide-rich historical waste rock, stockpiles and processed waste (eg tailings) at abandoned mines may also represent significant sources of critical (eg indium) or other significant metals (eg Sn) that if liberated economically could improve environmental conditions in and around abandoned and historical mines.CITATION:Fox, N, Parbhakar-Fox, A and Lottermoser, B G, 2016. Critical and Deleterious Metal Deportment in Sulfidic Waste Rocks, Baal Gammon, North Queensland, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016