Search Documents

By Dmitrievskaya TY, Cheremnykh PA, Kuftinova IV, Yaremenko VN

The comprehensive processing of raw materials and the tendency to waste-free production require the combination of various methods of concentrating mineral resources. Magnetic separation, an ecologically clean method of concentration, is one step in the technological cycle of ore processing, and cleaning and classifying of raw materials. Separators with superconducting magnetic systems cooled by liquid helium are the novel equipment for practical concentration. Recently, high-gradient (HGMS) and open-gradient (OGMS) magnetic separators using the effect of superconductivity have appeared. The separators of the first type are expedient in the head-end of the technological cycle, as they are most efficient for processing of particles 100 ¦m and greater in size. In this case the main task is to obtain pure tailings with a minimum amount of the useful component. This method allows the essential reduction in the cost of the subsequent crushing and grinding, because only the magnetic concentrate is directed to further processing. The separators of the VGMS type are used more efficiently in the final stages of the concentration cycle to condition the end product. The present work is devoted to the theoretical and experimental investigation of the motion of weakly magnetic particles in the working chamber of superconducting separators of the open-gradient magnetic separator (OGMS) and HGMS types. The flat OGMS is equipped by a magnetic system with NbTi racetracks cooled by liquid helium. The chamber is divided into zones by partitions parallel to the plane of the magnetic system. It is shown how, depending on the number of the zones and their depths, the extraction function of the OGMS varies and the transition from the OGMS to the HGMS occurs. The particles 2 mm and less in size are considered. The extraction parameter distribution of the particles was measured for a multicomponent weakly magnetic ore. It was experimentally shown that xD2 is the extraction parameter for the particles in the OGMS on condition that (p-po)D /l8/tl/g

Jan 1, 1993

By X Zheng, P Manton

Pebble recycle crushing circuit performance at Telfer has historically fallen significantly short of the design product P80 of 12 mm. An investigation was undertaken to evaluate the current pebble crusher circuit performance, quantify the optimum performance achievable with the existing circuit and examine the impact of pebble crusher performance on the overall grinding circuit throughput. The primary objective of this investigation was to develop an operating strategy that could consistently deliver the finest possible pebble crusher product to maximise the overall plant throughput.The pebble crusher specific energy (Wc) was proposed as a key control variable for pebble crusher operation based on the results of plant survey work. Over the range of pebble crusher specific energies encountered at Telfer, a strong linear relationship was found to exist between Wc and the crusher product size. This direct linear relationship between specific energy and crusher product size remained constant regardless of how the change in specific energy was generated, ie through changes to the crusher closed side setting (CSS), feed rate, liner profile or moisture content. Key findings for the Telfer pebble crushing circuit were: each 0.1 kWh/t change in Wc resulted in a 4.9 per cent to 6.0 per cent change in plant throughput, each 1 mm change in pebble crusher CSS resulted in a 2.2 per cent to 2.6 per cent change in plant throughput, and 0.57 tonne of new feed was displaced for each tonne of crushed pebbles recycled to the semi-autogenous grinding (SAG) mill. The presence of an existing 3000 tonne pebble stockpile between the SAG mill and pebble crushers provides an opportunity to manipulate the feed rate to the pebble crushers independently of the SAG mill pebble production rate. This flexibility, along with excess pebble crushing capacity, enables the pebble crusher specific energy to be maximised the majority of the time. Pebble crusher specific energy has subsequently been incorporated as an online crusher control measure to assist in maximising plant throughput.

Jan 1, 2009

By Mez W

the German ruining industry uses different residues for hackfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes. a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the l)MT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer it secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

By J J. L du Plessis

Escalating energy and electricity costs have become one of the biggest expenditure drivers in mining operations. During the last eight years, energy costs have trebled when expressed as a percentage of total running cost in South African mines. Power consumption on mines is controlled by three main strategies, namely load clipping where energy use is reduced for parts of the day, load shifting where energy use is shifted to other parts of the day, and energy efficiency where energy use is reduced permanently.To reduce the operating costs of ventilating and cooling underground mines continuously, system optimisation studies must be completed. A part of this paper describes methods that can be used to reduce energy usage by optimising cooling and ventilation systems during planning and in existing operations using network simulation models that accurately reflect the current and planned ventilation conditions. These models are used to examine various options for improving the overall ventilation and cooling efficiency. Furthermore, an overview of refrigeration and cooling practices, and ventilation strategies is presented.Ventilation-on-demand and cooling-on-demand strategies have the potential to reduce both the capital and operating costs associated with mine ventilation and cooling systems. In addition, it has been proven that modern strategies and energy-efficient tactics are technically feasible.It is also important that the correct equipment selection is made. This must be based on the best technology with the highest energy efficiency. Where equipment replacement is being considered, energy efficiency must be one of the key decision drivers.In this paper a number of studies were presented and from the experience and the data presented it is clear that a large financial benefit is possible through optimising ventilation and cooling during the planning of mines or within an existing operating mine.CITATION:du Plessis, J J L, 2015. Strategy and tactics implemented to achieve energy-efficient ventilation and cooling of mines, in Proceedings The Australian Mine Ventilation Conference, pp 9–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Smith, R Beckie

Controls on environmental loading from acid rock drainage (ARD) are not well understood in waste rock material. In particular, relationships between subsurface flow and the timing, duration, and intensity of leaching of metals and acidity from waste rock dumps remain ill defined. This study investigates field-scale relationships between subsurface flow processes and geochemical processes in unsaturated waste rock. A 12-metre tall, unsaturated waste rock pile, constructed in 1994, was deconstructed and sampled at Key Lake, Saskatchewan, Canada, during the summer of 2000. A detailed sampling methodology was developed to characterise physical and chemical properties of waste rock material within the waste rock pile. Physical properties were characterised by measuring soil-water suction, volumetric water content, and grain-size distribution at 60 random locations within the pile and grain-size distribution at 20 grid locations within the pile. Attempts to develop a field-based soil water characteristic curve from physical field-data failed due to spatial variability and hysteresis of waste rock properties. As a result, grain-size distribution was used as a relative measure of subsurface flow. Paste pH, pore-water geochemistry, mineralogy, and water-soluble extraction results were used to characterise geochemical processes and sulfide oxidation at each of the 20 grid locations. Geochemical characterisation results demonstrated the preferential weathering of marcasite relative to pyrite and chalcopyrite. Dolomite was the main buffering carbonate mineral. Gyspum, jarosite and iron oxyhydroxides were the main secondary minerals. Pore-waters contained up to 800, 11.7, and 6 mMolar (78 000, 690, 1400 mg/L, respectively) of sulfate, nickel, and uranium, respectively, suggesting significant weathering has occurred. Measures of weathering indicators show no discernable correlation with grain-size distribution nor do they show any spatial relationship within the sampled grid. Reasons for this may include limited duration of waste rock exposure to weathering and development of fluid flow-paths, and limitations of characterisation methods used. Indeed, six years may not be long enough for weathering patterns to develop due to fluid flow-paths in this unsaturated waste rock pile.

Jan 1, 2003

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By I Gray

Other than being reasonably certain of the average vertical stress being lithostatic, there can be little certainty about stress in the ground. The stresses and strains in rock are a function of gravitational effects, external load, thermal changes, diagenesis and their mechanical properties including elastic, creep and post failure behaviours. It is highly desirable to measure stress where mining is going to take place, even if the virgin stress condition has already been changed by mining. The concept of some far field stress value that is more or less constant is usually invalid and can be dangerous to use in mine design. Measuring stress is not simple. The basic processes are broken into two categories, one where the rock will not fail around the borehole in which the stress is being measured and one where the rock has failed or will fail. Because of the complexity and cost in obtaining a single, precise stress measurement it is highly desirable to have some system to be able to obtain an idea of the uniformity, or otherwise of the stress situation between precise measurements. Table 1 shows the methods for measuring stress. The first five methods work on the basis of some fairly direct measurement of mechanical rock behaviour while the last three are attempts to get some idea of stress out of core long after it is removed from the host rock. While these latter methods appear to tick all the boxes for applicability there is a great deal of uncertainty in the results that they deliver. This paper reviews the methods for measuring stress and presents two new methods. These are a three dimensional overcore system to provide precise stress measurements in rocks that will not fail around the borehole and a core ovality system. The latter can be used to provide information on the stress difference orthogonal to the core. It is particularly useful because it can be used every metre of core length.

Nov 29, 2022

By Q Zhou, J Pan, D Q. Zhu, C C. Yang

Oxidised pellets have become an indispensable high-quality charge for blast furnaces (BF) due to their uniform particle size, high iron grade, high mechanical strength, good metallurgical performance, as well as relatively low energy consumption and gaseous pollutant emissions in pellet production. Nevertheless, due to the rapid development of the global steel industry, highquality pellet feeds are becoming more and more scarce. In order to broaden the source of pellet feeds and reduce the production cost of pellets, more and more steel mills are going to use coarse iron ore fines with relatively low iron grade and low impurities for preparation of desirable pellet feeds through a typical wet grinding-settling-filtering process. In this work, the grinding, settling and filtering behaviour of Brazilian and Australian iron ore fines are studied and compared, aiming at finding out the internal relationship between the mineralogical characteristics of different iron ore types and their grinding-settling-filtering performance. The results show that the grindability is heavily dependent on the hardness of iron ores, which is governed by the mineralogical characteristics of the raw materials. Usually the higher the hardness, the more grinding energy is required. Except for Brazilian specularite, Australian hematite-goethite type iron ore fines and Brazilian hematite ore fines exhibit good grindability with a Bond Work Index of about 10–15 kW•h/t. In addition, the settling and filtering performance of ground iron ores are largely affected by the density, mineralogical characteristics of iron ore fines (eg, quantity of clay minerals and goethite and porosity of ore particles), grinding fineness, etc. Generally, iron ore fines with higher density, lower quantity of soft minerals (clay and goethite) and larger particle size give superior settling and filtering performance. For iron ore fines with inferior grinding, settling and filtering performance, applying more energy-efficient grinding techniques, blending with ore types with good settling and filtering performance can reduce grinding energy consumption and improve settling and filtration rates to maximise the productivity of equipment and lower the operational cost

Sep 18, 2023

By Hemingway J, Read T. A, Anderson V. G

IN the determination of very small amounts of lead, the usual analytical methods are far from being satisfactory. Small amounts of lead may be present in the reagents empioyed, and it is customary to run a blank experiment to correct the error arising in this way. When the correction is of small magnitude compared with the amount of lead in the sample, this procedure may be adopted; but when very small amounts of lead are being determined it may happen that the lead found in the blank is as much, or even more, than the lead actually present in the sample, and the analysis has to be rejected. Moreover, the blank experiment cannot check errors which are not common to the blank and the analysis itself eg, the apparatus used in the parallel experiments, etc. It seemed to be desirable, tl;l.erefore, to make an investigation of the problem to ascertain, as far as possible, the nature of the errors arising from the introduction or loss of lead during the analysis, and how far these could be eliminated or corrected for; also, to determine the limits of accuracy of the improved method and the minimum amount of lead that could be reliably estimated.In the investigation, reliability and sensitiveness were regarded as essential features. Speed of operation, on the other hand, was considered of less importance. The amounts of lead dealt with being usually less than 1 mg, there is no alternative to the use of a colorimetric method. The latter, depending as it does upon the development of a brown coloration when ammonium sulphide is added to a very dilute -solution of a lead salt, is far from being a characteristic test for lead. Indeed, it is well known that the salts of most of the commonly occurring metals interfere with this test. Hence it is of vital importance that the lead should be isolated in the form of a pure compound possessing quite definite and characteristic properties before the colorimetric estimation is proceeded with...

Jan 1, 1921

By P J. Fairfield

"This paper reflects on the author’s experiences in undertaking mining studies and reviewing mining projects and technical reports, particularly over the past five years, and the impact of recent changes in reporting standards and listing requirements pertaining to mining-related evaluation and valuation exercises. It also discusses contemporary changes in the expectations of the investment community and the implications for the role of the technical specialist in providing advice to such stakeholders.Not for the first time in history, the resources industry has experienced a significant downturn after a period of strong, sustained growth in line with the traditional view of the cyclical nature of commodity markets. The resource industry is currently faced with capital austerity in the wake of projects ‘failing’ (not delivering to expectations). In response, the industry has experienced changes in investment behaviour (slowing of investment) and an increasing regulatory burden as stakeholders seek a greater understanding of mining project risks.This paper discusses this response and uses case studies to highlight the key learnings (perhaps re-learnt) by the industry. It also discusses the challenges faced by technical specialists in communicating the results of technical and valuation studies to the investment community.As investors seek to take advantage of the current stage in the investment cycle, the key challenge of the technical specialist is to effectively communicate the uncertainty in technical assumptions, risks and opportunities that drive project value.CITATION:Fairfield, P J, 2016. Managing expectations – from buyer beware to buyer be aware, in Proceedings Project Evaluation 2016, pp 66–74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T Hausler

The pitfalls, pleasures and management issues associated with international and remote projects are diverse.However, no problem is insurmountable and if an engineering team chooses (by luck or good planning) to push through the difficulties, success can mean an extremely satisfying experience for individuals and a significant, positive result for an organisation.International projects are not for the faint hearted or inflexible. Working in foreign lands with people who may or may not speak English and who may not initially respect you can become mentally and physically tiring.Sometimes the challenges are not fully explained to individuals in advance. Individuals then often learn about the challenges ù and discover solutions ù on the job. While this initially puts great pressure on individuals, matters improve eventually, especially when the locals come to understand that you are on site to make a positive difference.This paper will discuss aspects of a recent international project including meeting international clientsÆ expectations, dealing with cultural differences, social reckoning, environmental issues, and personal challenges. Specifically, it will cover aspects of working within a Russian cultural setting and overcoming social barriers.The paper also presents coping strategies for long periods of time spent away from home in remote places with extremes in weather beyond the normal experience of most Australians. For example, dealing with the effects of the spring thaw and coping with temperature ranges of -45 to +45¦C.Lastly, and possibly most importantly, there will be a focus on the role of translators. They have the power to make an engineer everyoneÆs best friend or, on your behalf, to order cold chicken liver and heart salad for lunch. If an engineering team can establish a working relationship with translators, they can become an invaluable asset and both on and off site.CITATION:Hausler, T, 2013. Achieving success in large-scale, remote area metallurgical plant projects, in Proceedings MetPlant 2013 , pp 539-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C Preston, T Williams, D Roy

The easiest way to mine valuable orebodies is through the use of explosives and well-planned blasting layouts that produce fragmentation profiles designed specifically for conveyance equipment in underground mines. The design of blasting patterns is specific to not only the explosives being used but also the rock or ore type being fragmented. Many blasting designs are based solely on the experience of those developed for similar orebodies in terms of properties and orientation or individuals that have some blasting experience.The primary technical objective of this paper is to outline a unique methodology for determining underground blasting methodologies (developing specific blasting parameters) commensurate with explosive energies and rock/ore equations of state for a narrow-vein gold property located in Northern Quebec and for underground mines in general.The procedures developed are to define the desired fragmentation specification so that a specific thermodynamic break is generated, taking into account powder factor, energy factor, tonnages, explosive energies and distribution along with blasthole diameter and orebody orientation for a specific set of explosive and dynamic rock/ore properties. Determining dynamic modulus values for the ore using seismic sensors to measure P- and S-wave velocities, the aforementioned parameters will be utilised to set the design constraints to maximise recovery and minimise overbreak and dilution.New underground blasting software (AEGIS) will use thermodynamic break in conjunction with defined fragmentation profiles to create an array of blasting parameters used to design and plan ring layouts. This software will also allow mining planners, prior to drilling and loading a production blast, to appraise future intended blasting patterns to minimise the potential of diluting ore with host rock and the likelihood of damaging mine support structures.CITATION:Roy, D, Williams, T and Preston, C, 2015. Underground stope drill and blast designs optimisation program, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 137–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

To explain in any depth the industrial relations of Broken Hill I believe that it is necessary to trace some of the many happenings that created the present industrial climate. While appreciating that our relations with the local industry are relatively good, it must be pointed out that to preserve and improve this present situation a duty is owed to everyone connected with the industry (workers, share- holders, etc.) by management and unions to see that just and reasonable agreements are found for any disputes. If the companies ever take the local position for granted it would soon die, killed by someone who may get some short term benefit, but who would lose something of incalculable worth in the long run. Similar- ly if the unions were to adopt some of the "wild cat" methods adopted in other parts of

Jan 1, 1975

By L M. van Niekerk

The mining of iron ore is a high volume low margin business because the value of this commodity is significantly lower than that of base metals. The main metallurgical challenges in most of the iron ore projects proposed for treatment nowadays have been in finding the optimum flowsheet for the treatment of magnetite ores, mixed magnetite-hematite ores and even ores that have banded ironstone formations (BIF). The associated plant designs incorporate very high capacity milling systems to grind the ore down prior to magnetic separation and in being highly capital intensive requires substantial investment in mega processing plants with associated infrastructure to mill down the run-of-mine ore to the desired treatment size for upgrading.To minimise the cost of infrastructure, better beneficiation techniques and technologies are being sought to assist in reducing upfront ROM feed to allow for reduction in overall treatment plant footprint necessary in extracting the desired downstream product. This paper discusses such beneficiation techniques and advancement in technologies for the upgrading of coarse and fine iron ore utilising dense media separation (DMS), jigging, wet magnetic separation, dry magnetic separation, flotation and x-ray processing.Another group of iron ore projects involve the mining of hematite ore below the water table. Often the mined ore is wet and sticky. This combination requires high capacity processing of feed material utilising large scrubbers or attritioning units to effectively remove the slimes component present in the feedstock. The fines removed, usually below 1 mm, are then discarded in large tailings storage facilities. Approaches to recovering the saleable material contained within these fines will also be investigated in this paper. This not only implies possible reduction in slimes discard footprint, but also holds potential benefit in augmenting overall yield and recovery of hematite product.CITATION:van Niekerk, L M, 2013. Fine and coarse iron ore beneficiation - An evaluation into global technologies and techniques, in Proceedings MetPlant 2013 , pp 584-598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R Hao

Uncertainties in large open pit geotechnical modelling has been a major concern for slope stability analysis. The level of confidence in the in-put assumptions, such as structural and rock mass model, dictates the modelling results to some extent. This article is to detail a case study of Kalgoorlie Consolidated Gold Mines (KCGM) regarding a predicted inter-ramp failure on an as-built pit walls by a 3D numerical modelling. Significant concerns were raised across site and multiple preventive plans were considered. After intense data collection work, it was confirmed that the risk of failure had been overestimated. The case study has improved the understanding of geotechnical data in-put and has enhanced the process of creating and updating geotechnical structural models at KCGM.

Jun 22, 2022