Search Documents

The Lane Cove Tunnel (LCT) is an important infrastructure link in New South Wales (NSW) and runs from the end of the Gore Hill Freeway at Artarmon at its eastern extremity, to the end of the M2 at North Ryde at its western extremity.  The LCT is 3.6 km long and generally consists of twin two/three lane unidirectional tunnels running largely under Epping Road from just east of Mowbray Road, west to the western end of the Gore Hill Freeway. The tunnel opened in early 2007. The presentation will provide a summary of the traffic and emission modelling performed for selected representative surface road sections in the vicinity of the Lane Cove Tunnel. An assessment of the predicted impact of vehicle emissions on ambient air quality in the corridor as a result of changed traffic conditions due to the tunnel opening will be presented. The traffic modelling and emission calculations were undertaken for the following two scenarios: Year 2006 û Lane Cove Tunnel no-build option, and Year 2006 û Lane Cove Tunnel build option. Vehicle emission calculations for the four main pollutants from vehicles: CO, VOC, NOx and PM10 on the surface roads in the vicinity of the Lane Cove Tunnel were performed using the predicted daily traffic for the two cases (no-build and build). The analyses indicated that the vehicle emissions for all pollutants are expected to significantly reduce in the corridor with the building of the Lane Cove Tunnel, including the areas in the vicinity of all tunnel portals, when compared to vehicle emissions for the no-build case.  As a result of the decreased vehicle emissions on the surface roads, the study concluded that the actual ambient air quality is expected to improve in the corridor including the tunnel portal areas after the Lane Cove Tunnel opening.

Jan 1, 2008

Listing on Australian Stock Exchange Limited ('ASX') is a means by which a company can prosper and grow by gaining access to a large capital market. This currently stands at over $300 billion for domestic securities listed on ASX. A company seeking listing will benefit from a higher profile and a greater spread of shareholders. These result from, among other things, improved communications with the investment community. ASX recognises that a decision to list is an important step for a company. Owing to the diverse nature and size of the companies that consider listing and the various steps involved, it is recommended that guidance of professional advisers is sought as early as possible in the listing process. A company seeking listing on ASX must meet the prerequisites for admission to the Official List which, along with the continuing obligations that must be complied with following admission, are contained in the Listing Rules of ASX. Listing on ASX requires a company to ensure that, among other things, the market is fully informed at all times so that investors can make informed investment decisions.

Jan 1, 1996

By D J. Alchin

Most of South AfricaÆs high-grade iron ore resources are hosted within a fault-controlled structural basin in rocks of the Palaeoproterozoic Transvaal Supergroup in the Northern Cape Province of South Africa. Iron mineralisation occurs as individual orebodies in fault-bounded basins or as fold-controlled concordant lenses around an unconformity plane above the Kuruman Banded Iron Formation. The Sishen mine near Kathu and the beeshoek mine and Sishen South deposit near Postmasburg lie on the northern and southern border of a major domal structure known as the Maremane dome, respectively. The effects and structural constraints of at least three orogenic compressive episodes and several intermittent extensional episodes on the formation, erosion and preservation of iron mineralisation on the Maremane dome and surrounding environs were investigated. Ventersdorp impactogenal rift basin development at ~2.78 - 2.64 Ga, finalised with the deposition of the volcano-sedimentary Vryburg Formation during the thermal subsidence stage at ~2.64 - 2.6 Ga, and was followed by tectonic quiescence/stability and an extensive marine transgression across the entire Kaapvaal craton. The drowning event led to the formation of a carbonate platform with the deposition of the Schmidtsdrif and Campbellrand subgroups conformably above the Vryburg Formation at ~2.6 - 2.52 Ga. The initiation of distal (to the west of the Kaapvaal craton) off-craton oceanic rifting, causing submarine volcanism and associated hydrothermal activity, led to the deposition of initially manganiferous chert (Wolhaarkop Formation) followed by banded ironstone formations (Manganore Iron/Kuruman Formation) of the Asbestos Hill Subgroup at ~2.52 - 2.46 Ga. Initial passive margin rifting along the N-S oriented western edge of the Kaapvaal craton, initiated at the end of Ghaap Group time (during Koegas Subgroup deposition) at ~2.46 - 2.35 Ga, formed a prominent system of N-S striking, westerly dipping normal faults. Easterly directed crustal compression in post-Ghaap Group time in response to the Kalahari Orogeny (accretion of Rehoboth craton along western edge (Kalahari suture zone) of the Kaapvaal craton at ~2.35 - 2.24 Ma led to the formation of large-scale regional, N-trending F1-folds. Partial to complete inversion of the Koegas passive margin rift system (ie reverse dip-slip reactivation of the N-S striking normal fault system to high-angle reverse faults and dextral strike-slip reactivation of the Ventersdorp rift system developed in the Archaean basement), was followed by uplift, erosion and formation of a regional angular unconformity (Postmasburg unconformity). Uplift was accompanied by deposition of fluvio-glacial sediments of the Makganyene Formation (Lower Postmasburg Group) within an intracratonic peripheral foreland basin setting unconformable above Ghaap Group strata at ~2.35 - 2.24 Ga. Post-orogenic crustal relaxation and rifting caused extensional reactivation of the N-trending Palaeoproterozoic passive margin rift system and NE-trending Neoarchaean Ventersdorp impactogenal rift system, forming a fault-controlled depository for the volcano-sedimentary Upper Postmasburg Group at ~2.24 - 2.1 Ga. Deceleration in rifting was succeeded by thermal subsidence of the Upper Postmasburg Group rift, erosion, formation of a regional angular unconformity and deposition of clastic sediments of the Lower Olifantshoek Supergroup unconformable above Postmasburg Group strata at ~2.1 - 1.93 Ga. Renewed rifting led to the deposition of volcano-sedimentary units of the Upper Olifantshoek Supergroup within a rift system superimposed on the Postmasburg Group rift depository at ~1.93 - 1.83 Ga. Easterly directed crustal compression during the Kheis Orogeny at ~1.83 - 1.73 Ga led to renewed inversion of rift structures of the Postmasburg Group and Olifantshoek Supergroup depository, N-trending F2 folding and thin-skinned thrusting of older rock units eastwards over the cratonic cover, thereby utilising planes of weakness in the strata such as prominent unconformities and lithological contrast boundaries as principal dTcollements. NNW-directed crustal compression in response to Lomanian (Namaqua-Natal) Orogeny at ~1.15 - 1.0 G along the southern margin of the Kaapvaal craton, resulted in minor sinistral strike-slip reactivation of the N-S striking fault system, the formation of extensional NNW-SSE striking fracture/fault zones and the development of ENE-trending F3 folds forming a F2/F3 fold interference pattern. Post-Lomanian tectonic events (eg the Pan-African Orogeny at ~650 - 500 Ma, the Cape Orogeny at ~310 - 240 Ma, and the Gondwana breakup at 205 - 120 Ma), caused only comparatively minor extensional reactivation of the pre-existing fault systems. Iron mineralisation was ultimately preserved from erosion by Kheis Orogeny-related N-trending F2 synclines and Lomanian Orogeny-related ENE-trending F3 synclines, in particular areas of interference between F2 and F3 synclines representing comparatively deep semi-circular trough- like depressions, as well as in half grabens formed adjacent to reactivated westerly dipping N-S normal faults. Support for relating the iron and manganese mineralisation to structurally controlled hydrothermal fluid flow during the Kheis orogenic event has also been found, and ongoing research is aimed at confirming and refining the hydrothermal model for iron ore mineralisation in the Northern Cape.

Jan 1, 2007

By R Bunduwongse

The oil crisis had repercussions throughout the world and most importantly on mining, where the drive to reduce the use of liquid fossil fuel led directly to the appearance and subsequent growth in the design of mobile crushers in late 1970s early 1980s, which heralded a new era in both quarrying and mining. Even though mobile crushing has now become common, even preferred in the quarrying industry, this has not been the case in mining. This paper looks at why, in spite of the initial optimism, this technology has yet to gain full acceptance in the mining industry. The paper examines some of the problems that have been encountered in the past and offers suggestions as to how they can be avoided by applying the appropriate technology. It then takes a look at the successful application of the semi-mobile in-pit crushing system used by Italian Thai Development Company (ITD), on the Mae Moh Phase 5 contract and examines how the techniques used successfully there could be applied to the industry at large.

Jan 1, 2007

The minerals industry focus over much of the past twenty years has been on cost reduction and production growth supported, but not driven, by technology improvements. Mergers and acquisitions, and the demands of financial markets, have been high priority items whereas research and development and technology based innovation have received less attention and have been cut back in many companies. Technology improvements will be critical if the industry is to make progress on the stated aims of improving energy efficiency, reducing water usage and maximising recovery from deposits. They will also be important for improving capital efficiency and in treating difficult deposits. However the role technology based innovation will play both in the overall industry, and within individual companies, during the next decade is quite uncertain. There are major challenges in progressing technology based innovation in an industry with limited technical resources which is dominated by long life high capital operations. Specific opportunities for energy and productivity improvements exist but face significant technical and structural barriers that need to be overcome if the industry is to significantly improve performance. Current evidence suggests that changes in approach will be needed for these improvements to be realised. Recent studies in the United States and Canada have highlighted the wide range of energy performance across the industry and the scope for marked improvement from both incremental improvements and increased research and development. Comminution, material transportation and underground mine ventilation were identified as high priority areas. Opportunities within these areas are discussed both in respect of specific technologies and in how they may change performance. The role of open innovation as a source of new technology is also discussed. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

By B Banerjee, N Kumar, S Parihar

Rampura Agucha Pb-Zn Mine (RAM) is located about 200 km to the south-west of Jaipur in the state of Rajasthan, India. Open pit mining operations commenced in 1988 and continued to 2018. RAM open pit footprint is the largest in India with length of 2000 m, width 1500 m and depth of 400 m. Development of an underground mine under the operating pit commenced in 2013, through trial mining longhole open stoping with cemented backfill was established as a preferred mining method. Nine years in operations underground mine has reached the production capacity of 4.5 MT, which represent more than 70 per cent of the ore volume mined by the pit. RAM is currently the world second largest underground Pb-Zn mine.

Nov 29, 2022

Project Sustainability Assessment - Matching Method to Enterprise Size Sustainable development requires managing natural resources, including minerals, in a way that is conducive to long-term wealth creation and the maintenance of capital (natural, social, human, economic and physical). One aspect of the minerals sustainability discussion focuses on replacing depleted mineral capital with other forms of capital so as to ensure that the contribution of a mineral project is net positive over its life. Another, equally important, aspect focuses on selection of projects and technologies that contribute to the achievement of a variety of sustainability objectives, such as environmental protection, efficient use of resources, water and energy, worker health and safety, and the equitable distribution of risks and benefits within and across generations. Technical feasibility and relative economic performance remain necessary decision criteria for mineral investment decisions, but they are no longer sufficient. Enterprises, regardless of size, are now confronted with the challenge of comparing investment alternatives based on a new, broader set of criteria. The field of integrated sustainability assessment (ISA) emerged in response to this changed social and business environment. ISA is a structured process for examining the economic, social and environmental impacts of a project or technology. The purpose of an assessment can be broad, a strategic review of corporate behavior for example, or quite narrow, input to a specific decision process such as the selection of a piece of equipment. There are numerous methods and analytical tools available to conduct ISAs and selection of the most appropriate for a given situation will depend upon temporal focus (retrospective to prospective), decision context (strategic, tactical or operational), and phase of the assessment process (problem structuring, analysis, resolution, ex post review), among others. Selection also depends upon enterprise size and the attendant availability of financial and human resources. Large multi-national firms often undertake complex, data intensive sustainability assessments, in part because the projects they are involved in are multi-faceted, long term, and require significant financial investments. Small and medium sized enterprises are seldom able to commit the same level of resources to an ISA, and if the projects they undertake are less complicated, a time consuming and detailed assessment may be unnecessary. Regardless of enterprise size, the tangible and reputational benefits of conducting as ISA must exceed the actual monetary cost of doing so. This presentation will provide an overview of available ISA tools, categorising them in terms of their data requirements, methodology, outputs and applicability in various decisions contexts. Distinction will be drawn between situations where reasonable approximations of project impacts can be expected to provide an adequate amount of information and those for which more detailed analysis is essential. Finally, ISA strategies that have been successful and cost effective at different scales of business enterprise will be identified. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Ramsden AR, French DH

The limited contrast range of conventional black and white imaging does not enable full use to be made of the dynamic range of the video signal obtained from a scanning electron microscope or microprobe. The use of false colour substantially increases the information that can be derived from such images enabling relationships to be displayed that cannot be observed in black and white. This capability is now used extensively in combination with quantitative electron microprobe analysis as a research tool for ore characterization and host rocks studies related to minerals exploration in the CSIRO Division of Exploration Geoscience.

Jan 1, 1989

The mining industry continues to faces significant challenges due to increasing resource constraints (quality of ore bodies, water, energy, human resources) and increasing license to operate requirements (safety, health, environment, location) from society, employees and shareholders. Technology advancements and hence research are necessary to ensure that the industry remains viable in this changing environment. Collaborative research is an important part of a company's research portfolio and offers the opportunity for the industry to work on generic issues that it is facing. Obvious benefits include the reduced cost to individual companies by sharing the costs, the opportunity to leverage government funding and the opportunity to conduct longer term projects resulting in skills development (PhD and MSc). Limitations of collaborative research include the reduced focus on company specific issues and the loss of competitive advantage from owning the outcomes of the research. The challenge for researchers and research managers is for them to demonstrate the value derived from longer term, pre-competitive collaborative research. The competitive advantage is not necessarily derived only from the outcomes of the research but rather from the company's ability to direct the research, translate the generic research outcomes to address company specific issues and to implement improvements at its operations. Implementation remains the greatest challenge. In this paper, case studies of selected collaborative research projects are presented to demonstrate key success factors required for implementation of research outcomes. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010

Outline of situations when valuations required - from capital raisings and takeovers, stamp duty, rates and capital gains tax, to probate and litigation between joint venture parties. Definition of types of exploration and mining properties as background to discussion on what methodologies to use (from grass roots to operating mine). Discussion on nature of alluvial deposits in New Zealand and how their characteristics and tonnage/grade uncertainties affect choice of methodology. Assessment of risk factors in New Zealand û technical, financial and socio-political (legislation, access, Maori land rights, environmental). Discussion of appropriate methodologies.

Jan 1, 1992

The OK orebody comprises a steep dipping narrow quartz reef averaging 0.4 m in width hosted in basalt and gabbro with porphyry bars cross-cutting through it. The following paper tracks the mining of this orebody, challenges encountered, measures undertaken to address these challenges and changes in mining conditions and methods as the mine matured in both depth and age. The initial mining method was narrow vein hand held shrink stoping accessed by shaft, that over the period of the mines life was superseded by gallery stoping, shrink stoping and ultimately mechanised narrow vein long hole sublevel open stoping. The reasoning behind the change in mining methods is detailed, including safety and cost benefits. The transition presented many challenges that were overcome, resulting in the successful development of a narrow vein long hole stoping method. The lessons learnt during the transition period and the practices and principles developed for successful mining of narrow vein orebodies using long-hole open stoping methods are summarised in this paper. The final section of the paper takes a retrospective view of how the knowledge gained through the mining of the OK orebody would be applied to a new mine containing an orebody of this type, with consideration given to the initial excavation design, equipment selection, mining sequence, geotechnical investigations and mining method used.

Jan 1, 1998

In 1987 the control strategies at the then ZC Mines' New Broken Hill Consolidated concentrator were a miscellaneous mixture of computer hardware and technology for ISA, grinding and residue thickener control. Field instrumentation was based on current-to-air technology of approximately the 1960s. Decisions were made to rationalise computer and field instrumentation technologies; the object being to consolidate control loops into one system to enable expansion of the system to include all facets of plant operation. The first stage was to install a DEC Micro PDP 11/23 computer and serial line communication as recommended by AMDEL Ltd, for the ISA system, as discussed by Walsh and Freeman (1988). The second stage was to select and install a distributed control system for the centralisation of the control loops into one system, and to replace field instrumentation with state-of-the-art technology. This paper deals with the second stage of the rationalisation, in an attempt to give an insight into what is required when personnel are faced with such a decision, details of costs involved in keeping a system functioning and utilised; and the requirement to train personnel for acceptance of further control strategies.

Jan 1, 1991

By Kametani H

Since pyrite is a semiconductor, the relationship between the leaching rate and the semiconducting properties is of interest. In order to investigate this relationship, a pyrite concentrate (95% FeS2) was oxidized at 90¦C (363 K) in an acid solution containing 100 g/dm3 H2SO4 and 1.0 to 25.1 g/dm3 total Fe. The suspension potential (Pt vs. SCE) was maintained at the desired values, within the range 0.40 to 0.70 V, by controlled additions of a KMn04 solution during leaching. The results were analyzed using a simplified kinetic expression. The rate constant was independent of the Fe concentration, while it increased with suspension potential. Partly oxidized samples were then prepared at varying fractions of reaction. After removing the elemental sulphur formed, they underwent thermoelectric power measurements using a packed bed lying in a temperature gradient. The value of thermo- electric power increased from about 0 to 30 pV/K in the early stages of oxidation. The results obtained are compared with those for chalco- pyrite reported in a previous paper.

Jan 1, 1987

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

Since gold was first discovered, mining development in the West Australian goldfields has been heavily dependent on the location of groundwater both for potable and mineral processing supplies . The location of adequate and economic sources of water has been a constant challenge to both explorers and developers throughout the history of the goldfields. The provision of a piped supply from Mundaring in 1903 greatly alleviated pressure on scarce resources, lowered mining costs and permitted the orderly development of infrastructure. However, increases in the demand for water resulting from new mineral discoveries over the past three decades has led to renewed pressures for more local supplies to be established. Wide-ranging groundwater exploration took place in the late 1960's and early 1970's, also, more recently, in support of intensified gold exploration. The collation and interpretation of the hydrogeological data from the whole goldfields region indicates that despite a low mean annual rainfall of between 180 and 350 mm, quite marked differences exist between the rates of groundwater recharge in different parts of the area, In general, these can be shown to diminish in a southerly direction contrary to a trend towards increases in annual rainfall. Recharge rates are related mainly to differences in rock weathering pattern, geological structure and physiography. The same differences have controlled the pattern of groundwater salinity and the magnitude of groundwater storages associated with the palaeodrainages. In the vicinity of the northern and western watersheds with the Gascoyne, the superficial sediments tend to be thin, may have calcrete in the section and contain moderate storages of brackish or even fresh water. This contrasts with the lower regions of the palaeodrainages where calcrete is absent and deeper erosion has permitted the accumulation of relatively large thicknesses of fine-grained sediments which are saturated with hypersaline water and constitute substantial storages. Account must be taken of these characteristics if water supply sources are to be optimised to meet the growing demands for groundwater in the region.

Jan 1, 1988

By Booth S. A, Milton D. W

Stratabound/stratiform and remobilised mineralisation have been recognised as the two dominant styles of mineralisation which constitute the Broken Hill ore deposit. Recognition of prospective sites for accumulation of ore depends on understanding the heterogeneity of the ore environment and the distribution of the two styles of mineralisation. The internal stratigraphy of the Broken Hill ore deposit and its enveloping rocks, is described, and a generalised stratigraphic setting of the stratiform mineralisation is outlined. Fhiphasis is placed on the existence of closely-spaced sub-basins as potential sites for ore accumulation close to the Broken Hill ore deposit. Further from the immediate ore environment, recognition of the same diagnostic stratigraphic sequence

Jan 1, 1983

By Kane, M O&apos

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan will total approximately 3.3 billion tonnes. Approximately 15 per cent of waste materials contain zones with varying amounts of sulfides and carbon and are referred to as æreactive shaleÆ. Reactive shale has the potential to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulfide rich zones also have the potential to generate acid rock drainage (ARD). Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments. Safe storage of reactive shale is the focus of ongoing research. Since the mid-1990s, a number of trials have been undertaken at Mt Whaleback in order to further the understanding of the physical and chemical properties of reactive shale. This paper summarises some of these trials, and discusses key learnings arising from interpretation of results. Ultimately, the learnings from this research will provide the guidelines for successful storage of reactive shale.

Jan 1, 2003

The Kwademen Au deposit was discovered in 1977- 1978 following a regional geochemical survey carried out as part of a UNDP (United Nations Development Programme) and BUMIGEB (Bureau des Mines et de la Geologie du Burkina) mineral exploration programme. The climate in Burkina Faso is rather dry, with markedly seasonal rainfall averaging 800 mm pa in the Kwademen project area. The relief is low and the drainage poorly developed, so that soil sampling was preferred to stream sediment sampling. Rocks have been subjected to deep lateritic weathering, so that they are transformed into a mixture of Fe-oxides and kaolinite over depths varying between 30 and 40 m. At the regional stage, soil samples (30-40 cm depth) were collected a a 300 x 500 m grid. The Kwademen deposit was indicated by Cu, Zn, Mo and Au anomalies. Subsequently, an area of 9.2 km2 was covered by a detailed geochemical survey by soil (100 x 50 m) and auger sampling. The regional anomaly was fully confirmed, and subsequent drilling intersected mineralized ore shoots, justifying the establishment of an evaluation project led by the U.N.R.F. (United Nations Revolving Fund) in 1983- 1985.

Jan 1, 1988

By Hale Y. M

Multielement reconnaissance geochemistry coupled with ground scintillation gamma ray measurements has been used to investigate the dispersion patterns of uranium and other major and trace elements in the arid Palmyrides region of central Syria. This region occupies an interplatform depression in the northern part of the Arabia Plate, upon which sediments up to 10 km thick have accumulated. Outcrops of strongly fractured Mesozoic and Cenozoic rocks form two major mountain belts, the northern and southern Palmyrides, between which is located the closed Ad-Daww basin, with a thick Neogene and Quaternary clastic cover. Among the various lithologies, phosphorites are well represented. Uranium and associated elements have been incorporated into the Upper Cretaceous and Lower Palaeogene sediments, especially the phosphorites, which are well represented in the region. These elements are derived from three possible sources, namely, sea water, Lower Cretaceous volcanism and metalliferous fluids leaking along taphrogenic lineaments. In and around the phosphorites, numerous traces of secondary uranium mineralization occur. Over 500 geochemical samples of outcropping rock, wadi and playa sediments, overburden and groundwaters were taken over an area of approximately 9000 sq km. Most samples were analyzed for 25 major and trace elements by nebulization ICPAES; for As, Sb, Bi and Se by hydride generation and ICPAES; and for U, Th and La and other REE by neutron activation analysis.

Jan 1, 1988