Search Documents

By Saghafi A

Spoil piles are produced routinely in open cut coal mines. Spoil piles may contain waste coal and other carbonaceous horizons. Coal and carbonaceous materials react with oxygen in the atmosphere, producing heat. If the rate at which heat is generated is greater than the rate at which heat can be dissipated, the temperature of the spoil pile rises. If the heating remains unchecked, spontaneous combustion can occur. Spontaneous combustion poses significant safety, environmental and economic problems if it should become established in spoil piles. Using the basic features of self heating in spoil, the use of model is directed toward developing quantitative prediction of spontaneous combustion in open cut coal mine spoil Piles.

Jan 1, 1998

The Sto Tomas II orebody of Philex Mining Corporation is a porphyry copper deposit located at Padcal, Tuba, Benguet, Philippines. It was mined through open pit method for the first two years starting 1958 and subsequently through underground method using the Block Cave System. The slusher type of draw was employed at the upper levels of the orebody from mid-year of 1959 up to 1994 and then shifted to LHD as the ore became more competent at the lower levels. Application of rock mechanics played a vital role during the conceptualisation of the LHD method of draw, the first of its kind in the Philippines. Rock mechanics is a combined responsibility of the geology and the mine engineering staffs, with the geology providing the vital information to the mine engineering to include in the mine planning the following:the general geology of the orebody; the ground characterisation through rockmass classification; determination of the cavability of the ore column (this includes our experience on airblasts which occurred during the early stage of our last slusher blocks); undercutting sequence; fragmentation of the rockmass in the ore column; drawzone spacing; proper draw control procedure; lay-out of openings; and the design of ground supports based on the rockmass condition. For the proper interpretation of the rockmass that would cater to the diverse mining situations, Philex adopted the modified geomechanics rockmass classification (Mining Rockmass Rating, MRMR) as this system is recognised and used by most of the block cave mine worldwide. This paper aims to discuss and present the role of rock mechanics in the analysis and determination of geomechanical issues encountered in Philex mechanised block cave operation.

Jan 1, 2000

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992

By Arit I, Adisoma G

General Limit Equilibrium Method (GLE) and Janbu's Generalised Procedure of Slices (GPS) are two limit equilibrium methods in slope stability analysis which satisfy all equilibrium conditions. Numerical difficulties associated with these metho

Jan 1, 1998

Rajor intrusion-related Cu and Au dep- osits along the Cordilleran-type central Andean margin and in the western Pacific island arcs constitute a series of discrete, linear belts which correspond to limited (414 m.y.) metall- ogenic epochs. The most important metallogenic belts, all of Cenozoic age, are inferred to have been generated during relatively shallow subduction of oceanic lithosphere beneath con- vergent margins. Geological and isotopic evid- ence suggests that magmatic rocks and associated Cu and Au mineralization were derived from asthenospheric mantle sources, which were enriched in a variety of elements (metals, alkalis, S) by dehydration of subducting oceanic crust. Where exceptionally rapid, low-angle 3ubduction took place beneath very thick (>50 km) continental crust, as in the central Andean Altiplano in the Miocene and southwestern North America during the Laramide, ore-related magmas underwent wholesale crustal contamination. However, the associated Cu-Au mineralization is the same as that developed in primitive island- arc crust. In particular, the by-product Au and So contents of porphyry Cu deposits are inde- pendent of crustal thickness and the degree of crustal contamination as determined isotopic- Ally.

Jan 1, 1987

THE millng methods employed in the Mount Lyell Mining and Railway Company's mines are, perhaps, less known to the milling world than those of other important districts, due to the geographical remoteness and isolation of the Mount Lyell field,but they present many features which are unusual, and should be of interest to the mining engineer. Typical mining is carried out on an open-stope system, details of which are the result of local experience and evolution, and of which the outstanding feature is that the ground is so worked as to be largely self-supporting by virtue of domical form given to the stope roofs. It is locally termed "rill" stoping,' but differs widely from what is generally understood by that designation, chiefly in that the "rill" or slope is developed in every direction from a central focus, and not merely in directions followllig the strike of a lode or ore-body whose longitudinal dimensions are very much greater than its width. Such terms as "donie stoping" or "arched-back stoping" would be more appropriate and descriptive.The company's active operations' at the present time extend to the Mount Lyell and North Lyell mines, and, though the fundamental principles of stoping methods are the same in each, the dissimilarity of the ore-bodies, both in nature and mode ofoccurrence, necessitates considerable variation as to details to meet the respective conditions. The Mount Lyell pyritic body lends itself to the adoption of the .system in its simplest and almost ideal form, and a description of stoping in this mine willserve best to illustrate it, while later reference to details of practice in the North Lyell mine will indicate how it may be varied to meet more difficult circumstances.

Jan 1, 1915

By M Titley, E Maidens

Many gold deposits were mineralised by fluids and processes that also altered the host rocks. This alteration may often be a useful visual aid that distinguishes barren, low-grade from high-grade regions in a rock mass. Alteration intensity is commonly used in gold deposits as a visual tool, along with face sampling or grade control support, to define oreblocks and guide excavation in underground and open pit mining. However, alteration is not often used at the resource estimation stage. Mineralised lodes are usually defined by geologists using a ægeo-grade envelopeÆ, where a number of constraints are considered, including an (arbitrary) cut-off grade; the ænaturalÆ grade break between high- and low-grades; and geological features including structural, lithological or alteration continuity. The geo-grade envelope is usually thought to satisfy the requirements of stationarity for grade estimation, and is considered a single domain. This paper examines a modelling technique combining gold grade and alteration, applied to the Wallaby deposit in Western Australia, to imbue a greater level of detail to the grade estimation in a region tested by relatively sparse drilling. This was achieved by utilising the correlation of gold grade and alteration, along with the spatial characteristics of the alteration, when estimating grades within a number of lodes. The alteration-driven estimation was utilised in conjunction with an unfolding approach, and the use of probability estimates, to overcome geometric data constraints. This technique allows greater control and most likely provides a more reliable estimate of the mineable resources than a global grade cut-off when visual control is to be a major vector in grade control.

Jan 1, 2003

The Gj0vik Olympic Mountain Hall is the world's largest underground cavern for public use and was created primarily to facilitate the ice hockey tournaments for the 1994 winter Olympics in Norway. The cavern has a span of 61 m, is 91 m long and is 25 m high. Ordinarily, rock caverns have a span width of 15 to 25 m, however, temporary mining caverns of up to 60 m have been excavated and natural caves with even greater dimensions occur. The Gj0vik Olympic Mountain Hall is unique as it is for public use with a capacity for 5800 spectators. Blasting was conducted with a high production rate at normal costs due to detailed planning and strict supervision of each round. The initiation system and vibration monitors were the main tools to control vibration levels and to facilitate a high production rate. It was of utmost importance that the rock remaining in the roofs and walls was of high quality after blasting to avoid rock fall, rock slides and excessive maintenance work.

Jan 1, 1995

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

By Yates M. G, Rowlands A. T

Most geostatistical techniques applied to the estimation of ore reserves assume relatively unifonn grade and thickness within an ore deposit environment. In shear-hosted mineralisation this rarely occurs. The distribution of mineralisation is controlled by the kinematic and geometric variation within the shear zone. Although the kinematic variation is dependent primarily on the temperature (and consequently the depth) of formation of the deposit, the geometric variation appears to be relatively insensitive to this parameter. Shoot mineralisation is controlled either by the intersection of secoodary shear planes (brittle deformation) or the stretching lineation of the mylonitic fabric (ductile defonnation).Once the shear geometry is clearly identified, it is critical to review the distribution of grade and thickness of mineralisation. The practice of cutting high-grade intersections without reference to the shear model leads to underestimation of the amount of gold in the deposit. High-grade shoots may occur as pipe-shaped bodies within the system; their identification is essential for both resource estimation and mine planning purposes.

Jan 1, 1991

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

Strip mining offers the advantages of high productivity from both human and capital resources as well as high rates of production. Experience suggests that it will be advantageous to extend strip mining to the maximum pos- sible depth in order to minimize costs and maximize the recovery of the in situ coal reserves. Highwall and spoilheap stability pose significant problems. Deep working in strip mines is likely to produce a change from methods which are based upon the elevation of material followed by dumping, to methods involving elevation and horizontal transport. There is considerable scope for optimizing the types of machines and minimizing the amount of double handling.

Jan 1, 1975

By L J. Reynolds

Gold mineralisation at the Globe Progress deposit is hosted by a geologically complex zone of shearing and brecciation, within a package of deformed metasediments. Mineralisation styles range from quartz breccias and lodes to sheared clay pug zones and disseminated sulfides. A review of the diamond drill core intersections through the deposit indicates that critical hanging wall and footwall contacts can be a combination of sharp or gradational; visual or non-visual boundaries. Approximately 60 per cent of mineralised contacts can be confidently identified visually, particularly where associated with veining, distinct brecciation or shearing, and high sulfide content. However, the gold grade and distribution of disseminated mineralisation can be extremely difficult to estimate visually, with implications for resource estimation and grade control when mining. Using observed drill hole geology and assays, a new geologically based model for the gold mineralisation has been constructed for the deposit to reflect the expected variability of the mineralisation contacts. This new model will constrain resource estimation and also serve to act as a predictive model when open pit mining commences. Nevertheless, careful grade control practices such as drilling, trenching and supervised extraction of ore will be required to maximise ore recovery and minimise dilution during open cut mining.

Jan 1, 2006

By Bothe C

Froth flotation processes use different surface properties of the minerals to be sorted. In an aqueous environment the hydrophobic mineral attaches selectively to air bubbles and is lifted to the surface of a separation vessel, while the tailings settle towards its bottom. Besides the surface properties, the hydrodynamic conditions play an important role. With respect to the hydrodynamics the flotation process can be divided, for simplicity, in two sub-processes. The attachment of hydrophobic particles to air bubbles, the so-called mineralisation, demands a large number of collisions and therefore high turbulences. The phase separation however needs a deterministic movement of both the particle-bubbles-aggregates and the tailings particles and therefore a quiescent flow field. The optimisation of the overall process requires a separation of both sub-processes, especially when fine particles have to be sorted. In conventional mechanically agitated flotation cells both sub-processes take place in the same turbulent volume. For this reason they suffer from a decreasing selectivity with decreasing particle size. In flotation columns the mineralisation of air bubbles and the phase separation are performed in a quiescent environment. This results in high concentrate grades and at the same time in a very slow attachment kinetics, which must, especially for fine particles, be counterbalanced by a long residence time of the slurry.

Jan 1, 1993

By A S. Venkatesh, A Das

The Precambrian iron ore of Singhbhum-North Orissa region of eastern India occurs as part of the horseshoe-shaped broad synclinorium known as the Iron Ore Group (IOG) of rocks, which hosts the most important iron ore deposits in India. The Jilling-Langalota iron ore deposits are part of the IOG. Detailed mineralogical characterisation of different ore types has been carried out using transmitted and reflected light microscopy. Scanning electron microscope-energy dispersive spectroscopy (SEM- EDS), X-ray diffraction (XRD) and X-ray fluorescence (XRF) have also been used with a view to test the amenability of these ore types for beneficiation requirements. It has been observed that haematite, martite and goethite are the main iron-bearing minerals. Kaolinite and quartz are the major gangue mineral phases. Considerable mineralogical, textural and compositional variations have been observed among the different ore types. Characterisation data reveals that the massive and hard-laminated ores are of higher grade with very few interlocking textures having haematite and martite as major mineral constitutents. The soft-laminated lateritic and friable ores are relatively low-grade varieties containing various proportions of impurities with complex interlocking textures. The soft-laminated and lateritic ores are porous in nature and contain friable oxide and hydroxides of iron along with kaolinite, gibbsite and quartz. The occurrence of kaolinite, gibbsite and hydrated oxides along the cavities and weaker mineral planes of haematite and martite has been observed. The friable nature and high alumina content of these ores are attributed to these secondary phases. The nature of these ores is responsible for producing large amounts of alumina-rich slime during mining and handling operations. Suitable beneficiation schemes have been recommended for each type based on detailed characterisation investigations on these ores.

Jan 1, 2007

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.

Jan 1, 1995

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

This paper first describes the essentials of the slurry shield method and its achievements, then problems encountered during driving tunnels and their countermeasures, and finally shows problems to be solved in the future. The author works at Tekken Construction Co., Ltd. as a director. All the data cited are based on material gained from the slurry shield tunneling works undertaken by the said company. The mark, viz*, indicates that Tekken Construction Co., Ltd. has obtained or is applying for a patent in the U.S., Europe and Japan. 1. CONSTRUCTION RECORDS BY SLURRY SHIELD METHOD AND ITS PROBLEMS (1) Shield machines in the future should have the following characteristics; a. to be able to drive less cohesive soil b. to make no change to the ground water table level c. to make it possible to let people work in normal air pressure d. to cause less settlement at the surface To meet the above conditions various kinds of mechanical shields have been are tried, viz. limited air pressure type, rotary cutter with slit regulator, screw-discharge type, blind shield, etc. As far as the author knows, however, they are not 100% successful. Tunnels need their own accuracy in accordance to the usage. Both ease of driving

Jan 1, 1976