Search Documents

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

By Yongjin S

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including Modelling.

Jan 1, 1992

There are still vast areas of Australia in which either the hydrocarbon potential has already been indicated but from which no hydrocarbons have been produced or else are completely untested. Despite the lack of recent new oil discoveries, it is anticipated that initial gas discoveries in these areas will be followed by oil discoveries as has happened historically. General exploration activities are continually providing new information that is being input to update previous hydrocarbon assessments for Australia, and all indications are that future exploration efforts will discover a lot of gas, some small oil pools and there is a chance to prove a major new oil province. Because of this, it is anticipated that reserves growth will continue at the average historical rate of about 200 MMB/year until the year 2000. The most frequent scenario will be costly exploration resulting in small oil discoveries and high development costs. This, in the past, has resulted in low profitability for Australian oil exploration, but windfalls for the Australian government.

Jan 1, 1981

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

By Nickelsen J, Theisen KG, Hansen PH

The use of stationary calciners in the processing of aluminium hydroxide has emphas- ized the importance of Bayer hydrate properties with respect to particle breakdown during calcination and subsequent treatment. Test results from calcination of several Bayer hydrates to sandy alumina in the FLS Gas Suspension Calciner (GSC) were obtained in a 250 kg/h pilot plant unit. Particle breakdown during calcination was influenced by content of solid sodium oxalate, trapped in the hydrate particles and operating gas velocities. Owing to the design and operational principles of the GSC it is possible to reduce particle breakdown to at least the same as what is found in long rotary kilns. Other major advantages reviewed are obtained through simplifications in plant design and operation, pointing to low specific power and heat consumption, and generally low production costs, thereby providing an attractive alternative to fluid-bed calciners.

Jan 1, 1981

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

By Waters JC

Pseudoclastic hydrothermal alteration textures occur within quenched coherent dykes forming part of a subaqueous dome complex (-4 Ma) on Ponza Island, Italy. These textures are similar to those observed in considerably older (-500 Ma) subaqueous volcanic rocks at a number of localities throughout the Mount Read Volcanics in Tasmania and elsewhere in ancient volcanic sequences of this type in Australia. This is significant because the processes of formation, hydrothermal alteration and secondary mineralisation of ancient volcanic sequences may be better understood if we can make comparisons with modern analogues. Observations at Ponza imply that these pseudoclastic alteration features form synvolcanically or immediately after dyke emplacement and lava extrusion. This is compatible with scenarios presented for their formation in ancient sequences in the Mount Read Volcanics, Tasmania.

Jan 1, 1995

By Russell F. M

Following the accident in the Peterson section of Mufulira mine in September, 1970, a method had to be found of extracting up to 300 000 tonnes of ore per month from this area without inducing caving. Sandfill mining methods were chosen, necessitating a plant capable of producing both cemented and uncemented fill on a large scale. The paper covers the design and construction of this sandplant which is thought to be unique for its size, as it incorporates three 3 000 tonne capacity settled storage silos, a 500 tonne capacity cement silo, mixing tanks and a control room situated underground. The plant is designed to handle an aver- age of 440 tonnes per hour with a maximum of 660 tonnes per hour for limited periods, delivering either uncemented fill or cemented fill in proportions varying from 1:6 to 1:30. The instrumentation and equipment necessary to give one man operation of the plant is described and the fill mining methods now in use at Mufulira are briefly outlined.

Jan 1, 1973

By Purvis A. H, Greenwood-Smith R, Sowerby B. D

A nuclear technique for the determination of copper and nickel in bulk samples and drill core has been developed at Lucas Heights andfield-tested at Mount Isa. The technique, which is highly specific to the element being measured, utilises the gamma-ray resonance scallering process.A bulk mineral analyser was installed in mid-1976 for the routine assay of copper in bulk samples and drill cores, and remained in operation until late 1981. The operation of the analyser over this five-year period is reviewed with particular emphasis on reliability, accuracy and principal usage.The main application of this analyser was in stope planning and design whereby several thousand drill-core and Wall-chip samples were analysed. It was also used as an aid to underground grade control of stopes where ore dilution by supporting barren backfill was a problem.

Jan 1, 1984

By Thiel D. V

It is quite well known, although not so well documented, that radio noise is generated during rock fracture. Radio noise has also been observed during severe earthquakes. The source has been thought to be the fracturing of the rock, although the mechanism has never been unequivocably proven. A study of these radio emissions may provide insight into rock dynamics prior to seismic events, and after blasting. A programme of electric-field recordings has been undertaken at Brisbane quarries during multi-hole blasting. Preliminary analysis has shown that three types of signal may be distinguished. They are hole detonation, rock fall and post blast relaxation signals. It is thought that information about the blast, and the fracture of the rock, may be ascertained from these Signals.

Jan 1, 1990

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

The Tick Hill Gold Mine is situated approximately 110 kilometres south of Mount Isa, and 14 kilometres north of the township of The Monument. It was discovered in October 1989 by Mount Isa Mines Exploration in an area which had been targeted as high in potential for copper-gold mineralization.A mining lease application was made in March 1990. Mining, and the construction of the plant and infrastructure, began'in early August 1991 after the lease was granted on 20 June of that year. Commissioning of the plant began in December 1991, and the first gold was poured on site on 31 December 1991.The development of the underground mining operation commenced in January 1992 with the drilling of the ventilation shaft. The access decline was started in March of the same year, with the first ore produced from underground in August.

Jan 1, 1993

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By J Vann

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and û importantly û metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These ægeometallurgical variablesÆ drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many ætraditionalÆ (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007

Gunpowder Copper Limited processes 1,000 tonne/day of Mammoth ore in a conventional flot- ation concentrator. Run of mine ore is prepared for flotation by three stages of crushing and two stages of ball milling. The concentrate, in which the primary copper mineral is chalcocite, is solar dried and exported to Japan. The history of operation is summarised, and plant practice and metallurgical problems are discussed.

Jan 1, 1974

By Farrelly C. T

The Wiluna mining operations are centred near the township of Wiluna 750 kilometres north-east of Perth and 600 kilometres east of Geraldton.The Wiluna gold mines produced over two million ounces of gold, predominantly by roasting the refractory sulphide ores, before closing in 1947. In the period 1984 to 1992, 668 000 ounces of gold has been produced from free milling oxide ores and the retreatment of tailing. A plant capable of treating the refractory sulphide ores using the bacterial oxidation, Biox technique was commissioned in March, 1993.The Wiluna lode deposits are hosted by a sequence of very low grade metamorphosed mafic flows at the northern end of the Norseman-Wiluna greenstone belt. A strike slip fault system provided conduits for fluid migration; ore deposition occurred at favourable sites along the faults. Satellite mines at Gourdis and Wiluna South provide laterite and lode style oxide ores.The different styles of deposit and ore types at the Wiluna mining operations require a flexible approach to resource estimation and grade control practices.

Jan 1, 1993

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995