Search Documents

The increasing introduction of high capacity mechanical equipment into the coal mines of New South Wales following. tforld War II brought with it problems of roof support. Rapidly advancing headings in difficult country could not be supported with heavy, close,timbering due to the time involved in installation and the reduction of available' space for the movement of machines. _ The installation of low cost, space saving, rapidly installed roof supports became a necessity if the new mechanical equipment wa-s to be allowed to operate at maximum efficiency. As, a result of experience in the United States of America, the system of roof support using steel reinforcing bolts began to find increasing, popularity in the mechanised mines in this State. From the somewhat'crude methods of in- stallation adopted in some of the, early trials, the practice of roof bolting has advanced into a-highly technical operation, requiring care and skill to ensure optimum results.

Jan 1, 1971

By G Swayn, J Harpley

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluoride along with traces of cyanide. The disposal of SPL has been primarily in landfill because of difficulties in the development of a successful techno-economic SPL treatment process. Increasing concern about SPL landfilling practices is resulting in regulations in some countries to ban this form of disposal. As a consequence stock piling of SPL is occurring in an increasing number of countries pending the development of a successful treatment process. In 1992 Portland Aluminium investigated a SPL treatment process based on pyrometallurgical technology and approached a company called Ausmelt in Dandenong, Victoria, Australia, to ascertain if their submerged lance technology furnace process would be suitable to treat SPL. This approach resulted in Portland Aluminium, Alcoa and Ausmelt personnel working together on trials during 1992 - 1994 in Ausmelt's demonstration furnace to produce a slag and off gases containing hydrogen and sodium fluoride. The trials also evaluated the effect of oxygen enrichment to increase the concentration of hydrogen fluoride and the ability to recycle sodium fluoride particulate produced as the furnace off gases cooled. Other separate developmental work by Portland Aluminium, using CSIRO, resulted in the production of aluminium fluoride from the offgases from the pyrometallurgical process. The results of these projects influenced Portland Aluminium and Alcoa to authorise up to $A26 400 000 in December 1995 to construct a Research and Development processing facility to treat SPL at Portland. The Portland Aluminium unique gas treatment process converts hydrogen fluoride in the furnace offgases to aluminium fluoride in a multistage fluidised bed reactor, designed by Portland Aluminium. The aluminium fluoride produced in the reactor has been trialed successfully in Alcoa's aluminium smelting process as a replacement for imported aluminium fluoride. The installation in mid-2001 of a slag granulation system has enabled the production of a granulated vitreous slag having leachability qualities that conform to Victorian EPA criteria for the unrestricted use of the granulated vitreous slag from 'The Alcoa Portland SPL Process'. The unrestricted use of the granulated slag successfully completes 'The Alcoa Portland SPL Process' which treats the hazardous waste material SPL and converts it into non hazardous useful products.

Jan 1, 2002

By Morland R

Recent influence of backfill stability on stope production in the Copper Mine at Mount Isa Mines Limited is described. Changes to the mining process to improve fill stability are described, including increased focus on fill performance, modifications to extraction techniques, increased fill quality, changes to drill and blast practice, and research into backfill stability. Several case studies are described.

Jan 1, 1995

By McKee DJ

Future mineral processing developments will be of two types. There will be a continuation of the advances of the last 20 years including major increases in equipment capacities, the development of reliable on-line instrumenta- tion, the use of digital computers for automatic control, and the greatly expanded use of in-situ leaching techniques. However, there will also be a need for innovations as the industry faces a different set of problems to those involved in cost and extraction efficiency considerations. These new problems include those relating to energy usage, environmental pressures, and the further development of large low grade deposits and small, high grade metallurgic- ally complex deposits. Present technology does not appear adequate to solve many of these new demands. New treat- ment concepts will be required, and the immediate outlook in this regard is not encouraging. A major research and development task in mineral processing over the next 20 years will be to seek out new ideas and develop them, and this must be pursued with imagination and determination. Both the continuation of the present research pro- grammes and the development of new methods will require a steady supply of highly qualified technical personnel. These people are not being produced in the numbers required, and this situation must be urgently rectified.

Jan 1, 1981

The Matakan Unit of New Ireland, Papua New Guinea is a highly fossiliferous lagoonal deposit containing numerous coal pods and lenses. The unit is strati graphically part of the massive reefal Lelet Limestone of Miocence age. These organic-rich sediments have a high hydrocarbon potential as evident from microscopical observations as well as Rock- Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbo as Rock-Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbonaceous sedimentary rocks associated with the coal are rich in pyrite expressed in the sulphur content (19.7 - 22.8%). A high primary productivity and anoxic sediment pore waters or just above sediment - water interface have given rise to sufficient organic matter accumulations to yield a potential hydrocarbon source rock. Atomic H/C ratios of the coals are between kerogen type III and type II mainly, expressing the mixed nature of the coal and that of the associated sediments is type II. Early generated hydrocarbons (exsudatinite) have formed from pollen exines filling the pollen cavities and in places filling micro- fissures in the surrounding vitrinite.

Jan 1, 1987

The 250 metric tonnes of gold and 360 000 metric tonnes of copper recovered from the Mt Morgan Mine in Central Queensland justify its fame. The mine ceased operation before the advent of three-dimensional computer graphical modelling of orebodies became common practice in mine planning. The Mount Morgan Mine records however remain and are the database for this study. The Mount Morgan project takes ore deposit modelling one step further by examining the relationship between grade distribution within the orebody and key geological features, as a tool for exploration and development.The Mount Morgan gold and copper mineralisation is shown to be strongly lognormally distributed. The deposit has been split into three areas, using geological boundaries, each with different geostatistical characteristics. Important features include: the spatial relationship of near-vertical, high grade shoots with a ring dyke thought to be related to the North Dyke; separation of the high grade eastern stopes from the others along the Andesite Dyke; and lack of concentrated mineralisation along the Slide Fault.Recognition of these features is useful to those currently exploring the Mount Morgan district for similar style deposits, by stressing the importance, or lack thereof, of the geological features.

Jan 1, 1993

The coal basins that formed near the margin of Permian Australia were comparable in size with the Appalachian coalfields and with the European fields between Wales and Poland. They formed on the foreland side of a growing orogen in a system of linked transform basins formed by transtension on strike-slip faults. They were terminated and compressed when the Gympie volcanic arc was accreted to the orogen. Another huge system of Permian coal basins extending far inland from the Permian coast was also terminated when the Gympie Terrane was Accreted.

Jan 1, 1987

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By A B. Bell

The health and in some cases survival of mineral exploration and mining companies is, in today's markets, more dependant than ever on the effective use of information technology. The need for speedy collection, organisation, maintenance and distribution of corporate and project information is a phenomenon that will continue to strengthen with market thirst.Geographic Information Systems (GIS) provide a medium for storage, maintenance and retrieval of data, and Internet Mapping adds a technology for effective distribution of that data. Combining these technologies can return benefits both fiscally and technically by reducing costs of ownership in IT infrastructure and increasing the efficiency and effectiveness of both internal and external information delivery.GIS and Internet Mapping technologies have reached a practical stanza in their evolution and will continue to develop as a key business tool in the natural resources sector.

Jan 1, 2002

By M Devia, J Rapkoch

This paper is intended to help design engineers, operating staff and plant managers understand the principles of metallurgical gas handling systems design. It also explains operating, safety and energy savings issues that the designer should take into consideration in the design of process off-gas systems for sulfide smelters. Primary smelting reactors, converters, and other off-gas sources impose challenging duty requirements on the various components of the gas handling systems. This paper reviews the design of common system components including the hood for gas capture at the system inlet, gas conditioning, gas cleaning, ductwork, dampers, hot gas fans, and the appropriate use of instrumentation and controls. The engineer must also be aware of how ductwork system effects and heat losses influence system performance. Also, the analysis of a recently-designed gas handling system will be reviewed, which includes high-strength SO2 gas from a smelting reactor, asymmetrically located Peirce-Smith converters, and a gas mixing chamber to mix the gases before they are sent to two acid plants of different sizes.

Jan 1, 2005

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

By Croggon R

Passing a direct current through a jointed fine grained soft rock mass auses the movement of water by the process of electric-osmosis. There are other processes such as electrolysis which transport ions that interact with associated ions and can, in turn, be oxidised. This results in the dissolution products being transported towards the cathode electrode. In the cathode region the ferrous hydroxide is oxidised to ferric hydroxide %%ith consequent precipitation. The cracks and joints are current pathways, along which the ferric hydroxide is deposited. This deposition reinforces the joints and increases the shear strength. By adding calcium chloride to the anode, the rate of corrosion is increased with the concomitant increase of deposited ferric hydroxide along the joints. This, in turn, significantly increases the joint shear strength. The process is pervasive in that the current via the water paths travels through the crack and joint systems The result is that not only specific joints are reinforced but the cracks and mtciconnected voids are also reinforced.

Jan 1, 1997

By Pollard D. M

In the batch phase disengagement test, an organic and an aqueous phase are mixed together for a known period to produce a dispersion which may be either organic continuous (aqueous phase droplets) or aqueous continuous (organic phase droplets). The continuity of the dis- persion will depend upon the method of init- iating the dispersion, the conditions under which the system is operating, such as temper- ature and impeller speed, and the properties of the liquids, such as viscosity, inter- facial tension and solute content. Once the dispersion has been agitated for the required period, the agitator is turned off and the position of the coalescence interface and the sedimentation interface recorded as a function of time. This will produce a plot similar to Figure 1, where the overall dir- ection of travel of the droplets of dispersed phase is away from the sedimentation inter- face and towards the coalescence interface where the droplets coalesce with the homophase.

Jan 1, 1987

By McDonald K. J, Flann R. C

A liquid phase sintering (LPS) process for preparing basket anodes from nickel powder has been scaled-up and the innuence of compact green density and sulphur content, as well as sintering conditions (period and syngas now.rate) on the perfonnance of anodes has been evaluated. The product anodes have been tested in an industrial electroplating tank. It is concluded that if anode residues are to be minimised, then with a sintering temperature of 960"C, compact green density needs to be as high as economically achievable (85 - 87 per cent density of solid nickel) and the sintering period approximately 40 minutes. With these constraints, if residual sulphur contents of anodes are to be kept as low as those of commercial anodes, then the sulphur content of the green compacts would need to be less than 1670 ppm. At the same time, it is also found that residual sulphur concentrations as high as 2000 ppm are beneficial to anode pcrfonnancc and not detrimental to the quality of the electroplate. The ability of the LPS process to produce marketable nickel anodes for the electroplating industry is clearly demonstrated.

Jan 1, 1993

By Lee M. F

The Lady Loretta lead-zinc-silver mineral isation of north-west Queensland was discovered first by Placer geologists in 1968 as a result of a geochemical soil survey. The stratigraphic position, mineralisation and rock associations of the deposit are very similar to those of the Mount Isa lead-zinc-silver orebodies. Aspects of the exploration history, geo- chemistry and structural geology of the Lady Loretta deposit, are discussed. A geometric model of the Ore Horizon is given.

Jan 1, 1974

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By B Sulistianto, D Carrugan a, R K. Wattimena

Geological structure at PT Karimun Granite Quarry, in Karimun Island û Indonesia, has three primary joint sets that cross between them. These primary joint sets are the principal factor influencing the geotechnical safety of this quarry. In order to get stable geometry of the quarry in terms of height, width, and slope for single and overall bench, we need an appropriate stability analysis method to prevent failure and maintain stability. The Universal Distinct Element Code (UDEC) is used for this rock mass system. The geometries resulting from this analysis have been implemented and have given a stable quarry until now.

Jan 1, 2003

By M Manefield, G Bournival, S Ata

Asteroids contain an abundance of valuable resources such as: nickel, cobalt, gold, platinum and rhodium. Whilst the consumption of mineral resources on Earth continues to deplete, meteoroids have the potential to become a significant source of minerals. Even though the minerals content of asteroids may be relatively high, the valuable minerals are more likely to be only a small portion of the total ore present in the main body. The ores must, therefore, be processed to extract the metals of interest from the waste. Existing terrestrial technologies rely on manipulating the physical and chemical properties of minerals. The application of these techniques to asteroids processing, however, is not straightforward due to the presence of different conditions such as zero gravity and lack of water in space. This paper discusses potential separation and extraction techniques that can be used for processing of asteroids.CITATION:Ata, S, Bournival, G and Manefield, M, 2015. Resource recovery in space, in Proceedings Third International Future Mining Conference, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

For many years the mining industry at Broken Hill, New South Wales, Australia, was carried on with just sufficient attention to underground ventilation and hygiene conditions as to keep pace with necessity. However, the campaign against industrial diseases in other mining centres (notably South Africa) some years ago, brought the subject more prominently before local mining engineers.Throughout a period of several years, gradual improvement has been effected, and at the present time industrial hygiene is considered an essential part of the production operations of the various companies.In June, 1918, a move was first made by the Board of Trade advising an inquiry respecting the health of employees engaged in the metalliferous mining industry in the State of New South Wales. At the end of that year, a recommendation was made to the State Government by the Board of Trade that a Techni.cal Commission of Inquiry be appointed to examine and report upon the dust conditions of the metalliferous mines at Broken Hill. Following this a second report presented in 1919 made specific recommendations in respect to the scope of such a Commission. A Technical Commission of Inquiry was accordingly appointed and arrived in Broken Hill to inquire into the prevalence of miner's phthisis and pneumonoconiosis in the mines. Early in March, 1920, the examination of all mine employees commenced, and the work was completed in June, 1920. The full report of the activities of the Commission and the conclusions arrived at was officially published at a later date. Based on the recommendations...

Jan 1, 1940

A company tax rate based on profitability return, or as more commonly expressed, a resource rent taxation scheme has been intro- duced at various stages in the past by both Australian state and commonwealth governments. At present a number of overseas countries are applying this form of legislation to the taxing of sections of their mining industries. Within this study, ways in which this type of tax has been used are examined. The form in which the tax can be applied varies. 1. It can be selectively or universally applied. 2. The base on which economic return is calculated can be selected in a number of ways. 3. It can start operating only when high profit levels exist, or alternatively be the basis of a total taxation scheme. The implication for the Australian mining industry of the introduction of different types of resource rent taxation schemes is assessed within the context of previously enacted systems.

Jan 1, 1978