Search Documents

It is commonly accepted that govern ments have a role in the financing of mineral development. The reasons for government involve- ment are examined in general and in the light of the current situation in Aust- ralia, particularly having regard to the ownership of resources. A brief introduction is given to the new Australian Government bodies, the Petroleum and Minerals Authority and the Australian Industry Development Cor- poration, designed to fill a new role in mineral development, and to the basic changes brought about by the Australian Government's decision to become involved in the future development of the country's mineral resources. It is generally accepted that governments do have a role in financing mineral development. This acceptance does not seem to be confined to Aust- ralia alone but is more a worldwide phenomenon. Mineral development has traditionally been regarded as the pre- serve of private enterprise and there- fore is presumed-to be profitable, and so it is instructive to ask why there is this special role for governments.

Jan 1, 1974

Three main divisions of the. Proterozoic are recognised in the North- West of Western Australia. These are referred to, in order of decreasing age as the Mt. Bruce Supergroup, the Bresnahan Group and the Bangemall Group. The stratigraphy and distribution of each is described, their relative ages discussed and a brief geological history of the whole area is Presented.

Jan 1, 1964

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Tzung-mow Yao, S Ki, J Word, J Vinson

Properly designed evapotranspirative (ET) cover systems can greatly reduce the amount of infiltration and groundwater recharge (deep percolation) into potential acid generating mine waste. In arid and semi-arid environments, infrequent precipitation, low measurable subsurface fluxes, spatial variability within mine waste and cover material, and evapotranspiration from below the cover system create challenges to monitoring moisture flux in these systems. Sloped ET single-layer (monolayer) cover depths and a variety of reclamation treatments are being studied at a copper tailing impoundment in Arizona, USA. To monitor the performance of different ET cover systems in response to precipitation patterns, four different test plots consisting of two different cover depths and two different vegetation densities were instrumented with heat dissipation sensor nests. The sensors measure the soil water pressure potential and allow hydraulic gradients to be determined within and below the cover systems to depths of 180 cm. Three replicate sensor nests were installed in each test plot to account for variability in materials and test plot treatments. Data collection occurs twice daily and is ongoing. Weather during the 26-month monitoring period was characterised by two months of greater than normal precipitation followed by nine months of normal precipitation and 15 months of abnormally dry conditions. Monitoring data indicate that deep percolation occurs in response to periods of extended precipitation, however, drying was observed to depths of six feet below the surface in all test plots. Using conservative assumptions regarding tailing hydraulic properties, one-dimensional downward flux predictions based on the monitoring data indicate very low (Additional long-term monitoring and installation of deeper and replicate monitoring sensors into tailings without cover systems are recommended to evaluate the long-term ET cover system performance and develop a better understanding of deep percolation rates at the sites.

Jan 1, 2003

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

Stope control information at the C.S.A. mine is obtained by diamond drilling inclined holes from within the stapes. Practical mining outlines are determined from complicated ore contours by a joint mining engineering and geological study. Production holes to achieve this outline are individually marked up and checked. Stope control also extends to selective mucking of ore mixtures for metallurgical reasons and to marginal ore and waste mixtures for economic reasons.

Jan 1, 1969

By Heidecker A

Several types of drainage structure providecost-effective environmental controls for water supply to Charters Towers and its mining industry. Drainage groves maintain bank-levee, channel, pool, and spring structures. Failure of drainage structures leads to anoxic fermentation of channel fill releasing residues, such as arsenic, which would otherwise pass harmlesly by fixed on sedimentary particles.Experiments along drainage structures indicate that productive agroforestry could be integrated with expeditious development of groves to cope with environmental change.

Jan 1, 1990

By Gillies A. D S

A device has been developed for modelling the behaviour of coal under conditions which may lead to spontaneous combustion. It is designed to model the behaviour of a stockpile of large mass. The apparatus can test coal samples taken from the flow stream from mine through washing, stockpiling and transportation to the point of utilisation. It tests samples in an as received' condition and so takes into account the effect of aspects such as particle size and moisture content on propensity for spontaneous combustion to occur. Results of the preliminary tests undertaken are given and future applications of the apparatus are Discussed.

Jan 1, 1995

By Weller KR

Computer programs are described which help the metallurgist to process sample data from a plant survey; to carry out simple mass balance calculations; to present the results of circuit and equipment performance in convenient form; and to simulate the circuit response to changing operating conditions. The uses and limitations of these programs are explained by following through a case study of the sulphide flotation circuit at Cleveland Tin Ltd. The circuit was sampled, the data analysed, and some process inefficiencies established. Simulation calculations were then made to provide information on which to base decisions regarding possible circuit changes aimed at improving performance.

Jan 1, 1983

By L Keeney

Cu-Au porphyry deposits are large tonnage low-grade resources dependent on processing large volumes of material. The ability to understand and predict comminution performance is critical, as it is frequently the rate-limiting step during processing. Parameters required from geometallurgical mapping and modelling of comminution performance are: A×b processing domains based on impact breakage variability, and BMWi processing domains showing grind response variability which lead to Mine throughput domains for a specific comminution circuit configuration. Due to the cost and/or large sample requirements of traditional comminution tests, insufficient data density and distribution of comminution indices commonly exist, making it difficult to model and map deposit scale variability. One method routinely applied to three dimensional domaining is to have an a priori zoning based on geological features (lithology, alteration, mineralogy, textures), and then apply to all material within a given domain the metallurgical values measured on a single sample or average of samples from that domain. The problem with this approach is that commonly the geological domains do not reflect comminution response, therefore compromising the quality of the average domain estimate. To resolve this problem an alternate integrated geometallurgical mapping and modelling method is applied to model and map comminution performance at Cadia East. This paper uses a data set of ~32 000 assay measurements and geological logging information, integrated with ~150 comminution measurements to analyse and develop proxy support models for comminution indices (ie A×b, BMWi, and throughput) based on inherent geological variability. Discrete downhole comminution processing domains are created, mapping orebody response while maintaining inherent variability.

Sep 5, 2011

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

People in the work environment (and often elsewhere) are seen as a commodity (we use them for our purposes).The general accepted view of a Company is that shareholders are "The Company" and that they employ people to utilise their money in a particular field to generate more money to give a return on investment. To achieve this, capital equipment is purchased to fulfil a task and people are employed to use this equipment. Equipment and people are commodities purchased with money.The focus of this approach is MONEY. The equipment and people, and the use of them, determines the amount of money that can be generated. In this approach people are motivated by financial concerns. The harder the times the more money becomes the focus.

Jan 1, 1998

By Rintoul AH

Studies of many types and purposes are being carried out constantly by mining, minerals processing and other operating companies. Frequently, the staff requirements and special skills lie outside the resources of the operating companies, and needs arise for external consult- ing services. We examine the natures of a range of studies, the factors that influence whether they be carried out in-house or externally and then discuss the manner of execution. Aspects of both good and bad practice are highlighted in order to arrive at the basic principles that give the most benefit from study work. While the bulk of the discussion relates specifically to the execution of external studies of process plant projects, many of the observations can be applied equally to the execution of studies by one department of a large organisation for another, and also to studies of capital projects other than those involving process plant facilities.

Jan 1, 1975

Two ends of a longwall face are not only concentrated locations of equipment, but also provide ventilation and access. The roof strata stability here has an important influence on mining coal and safety. Based on field obser- vations in the gateways at Zaozhuang Colliery (Shandong Province) and model tests, the author developed a structural model of the overlying strata at the ends of the longwall face - the arc triangular cantilever plate - to which the elastic theory of plates can be applied. Factors influencing the stability of the cantilever plate and its breaking character- istics are discussed. Requirements and design parameters for supports at face ends are pro- posed, based on these factors.

Jan 1, 1986

Epithermal gold mineralisation was discovered at the Muyup prospect during regional reconnaissance exploration in 1986. Further exploration utilising routine techniques of stream sediment, panconcentrate, rockchip sampling and geological mapping resulted in the discovery of five auriferous vein systems located along northwest-trending fault zones. Scout diamond drilling was conducted on two of the vein systems. Mineralisation is hosted by a poorly exposed, mid-Tertiary volcanic inlier composed of intermediate and minor felsic volcanic rocks intruded by intermediate hypabyssal por- phyries. Gold is wholly contained in narrow steep-dipping hydrothermal breccias and quartz vein stockworks in which chalcedonic silica and fine grained quartz is the predominant gangue with minor adularia, carbonate, and sulphides. Alteration zoning is manifested as intense fracture-controlled silicification mantled by narrow clay-rich envelopes which in tam grade outward and downward into propylitic alteration or unaltered host rocks. Late advanced argillic alteration is superimposed on the vein-related altera- tion assemblages. Alteration assemblages and fluid inclusion data suggest that gold mineralisation occurred in response to episodic hydraulic fractur- ing and boiling of low to moderate temperature, dilute alkali-chloride fluids. The Muyup prospect represents the shallow eroded remnants of an epither- mal gold deposit enriched in Au, Ag, As, Sb and Hg. Low sulphur fugacities reflected by vein and alteration assemblages support an adularia-sericite classification (Heald et al, 1987) for this epithennal gold deposit.

Jan 1, 1991

Recognition is the most important aspect in the use of breccias as an exploration tool. Ore-hosting breccias occur in a wide variety of environ-ments, shapes, compositions and characteristics, but generally present favorable loci for the deposition of ore mineralization in epithermal, porphyry copper-gold-molybdenum, massive sulfide, carbonate-hosted, sedimentary lead-zinc deposits and others.

Jan 1, 1990

A computer programming language known as GPSS is described and possible applications for the mining engineer are presented. The language is continually being upgraded with improved versions appearing about every three years. The tremendous power of the language is considered by comparing it with standard engineering programming languages, such as Fortran or Basic. Sample problems that can be solved using the language are indicated. The advantages and disadvantages of the languages are also discussed.

Jan 1, 1987

A brief introduction is given of the scale and of some special features of South African gold mining; it is noted that great depth of mining and narrowness of the reefs, and hardness and abrasiveness of the rock are the main sources of the problems of the industry. The most inhibiting problems are: Excessive rock pressure occcurring in conjunction with rockbursts, hot and humid working places due to high virgin rock temperature and auto-compression of the air, and low level of productivity. Conventional solutions applied ordinarily in mining do not promise to eliminate, or even alleviate, these difficulties.

Jan 1, 1985

By Shrivastava P, Humphreys M, Guibal D, Deraisme J

Customer requirements concerning the final products of iron mines are extremely stringent. Because of this, there is an ever-increasing need for mine operators to monitor and strictly control the quality of their product. This quality, as measured by the stockpile grade variability, is the result of a very complex process, where natural characteristics (the orebody and its geology) are transformed through the mining technique (open pit, shovel and truck fleet, blending into stockpile). The only way to reproduce and hence to control the variability of such a system, which is composed of several interactive sub-processes, is by simulation. A complete simulation of a Hamersley Iron Pty Ltd (HI) ore deposit has been undertaken to forecast the impact and cost of various mining methods, mining schedules and product stockpile sizes on variability of chemical and physical characteristics of the products. The mining simulation was made on a conditionally simulated orebody. On a range of criteria, the simulation was considered to fulfil the objectives set and was a valuable aid to analysis of product grade variability, operating and capital costs, selection of equipment, mine scheduling and setting of product grade targets.

Jan 1, 1994

Almost all industrial products, such as buildings, cars, plastics, railways, radio and television sets, computers, and others are made from materials extracted from the Earth. Earth is main resource of energy and up to now; the energy has been derived mainly from natural resources. Mining industry has significant influence to the nature, sometimes evokes a devastation of nature. On the other hand we have got a lot of nice examples that good preparation, sensitive mining practice and consistent reclamation can minimise the negative effects. All the mentioned problems calls for effective tools for mine design, mine operation and mine reclamation. Third millennium brings next challenge given by advances in information and communication technology. The development of very sophisticated software tools provides to technical systems some features of autonomous æthinkingÆ and intelligent behaviour. We can find large effort and a lot of scientific papers reflecting last advancement in science and technology and providing inspiration for new mining technology of third millennium called Intelligent Mine. Some aspects related to creation and utilisation of æIntelligent ModelsÆ as a background of æIntelligent MineÆ are presented and discussed in this paper.

Jan 1, 2003