Search Documents

New Zealand Steel Limited is nearing completion of the environmental reporting and planning procedures for its proposed fivefold expansion to steelmaking at Glenbrook, and supporting mining operations at Waikato North Head. A report on the proposal to transport concentrate from the mining operations to Glenbrook has also been prepared and is awaiting release. This paper draws from these events, and by discussing some of the problems encountered, gives some guidelines for the preparation of an Environmental Impact Report.

Jan 1, 1981

By J Zhou, T D. McGrath, K P. Galvin, C P. Lowes, J J. Eksteen

Pre-concentration of low grade ores can improve the economic and environmental sustainability of an operation significantly, with opportunities for implementation ranging from run-of-mine to mill discharge depending on ore specific characteristics. For a gravity separation, where the performance is fundamentally constrained by mineral liberation, these feeds often represent a very difficult separation given the dominance of the relatively coarse gangue and fine liberation sizes. Thus, building knowledge of the feed through characterisation of the density distribution is critical to assessing amenability before progressing towards lab/pilot-scale test work and full-scale operation. The traditional approach to determining the density distribution typically involved sink/float testing, however, recent developments in hydrodynamic fractionation using inclined channels now offers a more cost-effective alternative with minimal health and environmental risk. A non-hazardous dense liquid, namely an aqueous solution of lithium heteropolytungstates (LST), is supplied as fluidisation to a REFLUXTM Classifier, consisting of a vertical section below a system of inclined channels, operating in semi-batch configuration. Fractionation is achieved by increasing the flow rate incrementally and collecting the particles to form a series of flow fractions. The purpose of this paper is to present this new method in the form of a case study, aimed at assessing the amenability of a low grade gold-bearing sulfide ore to pre-concentration. The robustness in the method is demonstrated through comparison with sink/float data, examining the density distribution and the liberation-limited product grade and recovery achievable. These data are then used as a benchmark to assess water-based continuous gravity separations conducted on the feed using a laboratory-scale REFLUXTM Classifier. This data set is used as the basis for process modelling and empirical validation for the recently established partition surface of the separator.

Nov 10, 2020

Investigations into the flotation behaviour of single minerals, mineral mixtures and ores at the CSIRO Division of Mineral and Process Engineering have led to the development of sophisticated laboratory flotation testing equipment. Both routine and complicated flotation investigations can be conducted in a precise and reproducible manner using procedures and equipment that have been refined over many years of conducting careful batch flotation testwork. Several important advances in flotation research can be attributed to changes in testing procedure developed as a consequence of the availability of this equipment. The flotation cell and ancillary equipment is described and associated developments and techniques discussed.

Jan 1, 1992

By D Smith, D Reid, D Bradshaw, C Brough

The Merensky Reef at Northam Platinum Mine in South Africa is characterised by a high degree of variability with respect to reef elevation (difficult to mine), as well as mineralogy and texture (difficult to process). Development along strike and down dip of multiple reef types has led to unpredictable run-of-mine characteristics that pose problems for the mineral processing circuit at Northam. Following mining terminology, Normal, Transitional (NP2) and Pothole (P2) Merensky reef types can be defined, and this geometallurgical study aims to characterise and understand the relationship between their mineralogical characteristics and laboratory scale batch flotation performance. The plagioclase-rich NP2 reef ore is the easiest ore to process in terms of capacity for high mill throughput as well as flotation performance. The lack of very fine-grained disseminated sulfide textures in the NP2 reef ore results in better liberation characteristics relative to the Normal and P2 reef types. Consequently, chalcopyrite, pentlandite and sulfide recoveries are highest for the NP2 reef ore. The lack of ferromagnesian minerals in the NP2 reef ore also results in the recovery of the least amount of floatable gangue during flotation tests. The Normal and P2 reef ores are similar to each other, with an orthopyroxene-rich mineralogy with associated alteration minerals. The P2 reef is also characterised by the highest sulfide content and degree of pentlandite liberation. Chalcopyrite, pentlandite and pyrrhotite liberation is only significantly increased by a change in grind for the Normal reef ore. The change in grind, however, only significantly affects pentlandite flotation performance and overall froth stability for the Normal reef ore. However, for all three ores, a small change in grind has a detrimental effect on pentlandite flotation performance.

Jan 1, 2008

By J Vann, C Seymour

Geology is generally treated as a æfront endÆ step in mine development. After infill drilling, the majority of resource estimation, mine-planning, development, mineral processing strategies and operational procedures are planned and implemented with little geological input, particularly in open pit operations. However, significant benefits in overall costs, cash flow, and technical risk reduction can be realised when sound geology is utilised more rigorously throughout the mining process. This under-utilisation of geology in the mining process has arisen due to a combination of factors:A lack of interest in, or knowledge of the full mining process by geologists. Few geologists fully understand where their inputs make critical impacts on downstream users. As a result of this, geologists generally do not focus their inputs towards areas of greatest value added, ie addressing issues critical for other members of the mining team. Most importantly, few geologists effectively communicate their results to the downstream users of their geology models. The results are that the potential benefits of geology, and the appropriate status of geology in the mining industry, are not fully realised. It is fundamental to realise exactly what geologists do. Geologists constrain geological processes and geometry. All geoscientific tools at the geologistsÆ disposal are geared towards one of these goals. An emphasis on geological processes is present throughout the exploration process, whereas in the resource estimation and mine development process an emphasis on geometry is required. The mining process is a web of disciplines that are attempting to optimise development of a resource to provide value to shareholders. Yet few people within these disciplines have a full appreciation of this web, and where sound geology inputs can add value through various feedback loops. Geology inputs do not end at the resource estimation stage, nor are they relegated to grade control implementation. If geologists have an appreciation of the mining process and close liaison with the other disciplines such as geostatistics, geotechnical engineering, hydrogeology, and mining engineering, they can significantly benefit project costs, timelines, and constrain technical risk by addressing their issues at the earliest possible stage. Furthermore, the mining process is not a single pass timeline, but an iterative process where the exploration, resource definition, mine planning and mining loop is continually repeated over the life of a project. Therefore, the potential inputs of geology are critical throughout the mining process. Effective communication of the impacts of geology inputs on downstream users is often lacking on mining projects. The most effective way to communicate geological results is through where it impacts most û project risk. Focussing all geology inputs and communication in terms of potential material risk allows the geologist to be more effective in contributing value to the mining process, and allows the downstream users of geology inputs to better constrain the risks associated with their aspects of the mining project. Through a program of geologists:taking an interest in the entire mining process and identifying critical areas for geology inputs to downstream users (the geologistsÆ clients); focussing geology inputs to address the potentially material issues on mining projects; and communicating their inputs to the æclientsÆ in terms of technical risk, geology will be much better integrated into the mining process. As a result, the potential benefits of geology throughout the mining process will be realised, and the status of geologists within the mining process will be elevated to a more pivotal position.

Jan 1, 2000

By K Hines

Anglo Platinum is the worldÆs largest producer of platinum group metals, and also produces large quantities of nickel, copper and cobalt at its Refining complex in Rustenburg, South Africa. In 1995 Anglo Platinum embarked on a smelter modernisation project, primarily to reduce site emissions to below the guideline limit of 20 tonnes per day SO2, but also to increase the converting capacity in line with future projected production profiles. To achieve these requirements the existing Pierce Smith converters were replaced with a single large Ausmelt converter and a new acid plant. This was the first time that an Ausmelt furnace had been used for converting, but it had the advantages of being a very robust furnace and was fully enclosed, giving good gas capture. It was thus considered the most appropriate technology from both a process and an environmental perspective. It also enabled the smelting and converting furnaces to be decoupled. The plant was commissioned from late 2001 and the first tap was in June 2002. Despite being a new technology, ramp-up has been similar to other large scale pyrometallurgical operations. Numerous process improvements have been made since start-up, most notably a change from two-stage batch to fully continuous, resulting in the plant now operating above design in terms of throughput. Optimisation of freeboard accretion control was also a major component of the ramp-up activity. This paper discusses the commissioning and ramp-up issues of the new Ausmelt converting furnace, concentrating on the design and process changes, and summarises current operating performance against the original design objectives.

Jan 1, 2005

By Clark IH

Numerical modelling is an effective aid for the planning and design of underground coal mines. With funding from the National Energy Research Development and Demonstration Program, CSIRO Division of Geomechanics has produced a workstation environment which will allow the Australian Coal Mining Industry access to a wide range of numerical design models. The emphasis is on usability and simplicity and the long-term aim is that the techniques should be used routinely at the mine site, so that, in the future, design of a new underground mine will routinely involve modelling of each proposed layout.Each of the five numerical analysis programs, FESOFt, FLAC, MNLAY, FEBLK and UDEC has both strengths and weaknesses. Some analyses with each program demonstrate areas when; observed in situ behaviour in underground coal mines has been successfully modelled, and the results of site monitoring provide a basis for comparison with the predictions of numerical models.

Jan 1, 1991

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

By Woodcock JT

Successful chemical control of flotation requires practical solutions to many problems. A brief discussion is first given of those para- meters which can be controlled and those which it would be desirable to control. Suitable analytical methods for application to flowing pulp and to clear solution from pulp are out- lined in relation to on-line and off-line control. Practical problems of deciding where a measurement is to be made or a sample is to be taken and how the sample is to be prepared and presented to the measuring device are then considered. Equipment calibration and maintenance are considered in relation to the above factors.

Jan 1, 1978

By Colquhoun L

Flooding velocities were measured in a laboratory column (96 mm 4) provided with both bottom and side air entry Packings used were 6 mm glass rings and spheres and -16 +8 mm coke. Results showed that when air was introduced through side nozzles flooding velocities were much higher than those obtained when air was introduced at the bottom of the column. Significance of the results and application to blast furnace flooding is discussed from the viewpoint of assymmetric gas flow.

Jan 1, 1975

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

The three systems of mining in use in the Southern Coalfield of New South Wales are bord and pillar with or without subsequent extrac- tion, longwall and shortwall. Bord and pillar with extraction is regarded as the conventional system. The application of continuous miners and powered roof supports (Shortwall) to coal min- ing has, grown in recent years from something of an oddity among extraction systems to an acceptable and viable approach in certain min- ing environments. The method can be applied in a high proportion of situations where normal pillar extraction is practised with advantages over the conventional approach. These advantages extend to both safety and efficiency aspects and also include better utilization of coal reserves. It holds hope for further gain in efficiency because its simplicity of layout lends itself to achieving the goal of contin- uous haulage towards which operators are always striving.

Jan 1, 1976

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By M Scamardella

The CSA Mine is located at Cobar, New South Wales, where it was in continuous operation from 1966 to the time it went into receivership on 29 January 1998. When it closed it was under the ownership of Golden Shamrock. Glencore International, in conjunction with Mt Lyell Mining, undertook a due diligence study to determine the feasibility to re-open the mine. This envisaged operating CSA Mine as a low-cost, copper concentrate producer under the direction of Cobar Management Pty Ltd (CMPL). The new workforce would consist of contractor trades people in operating functions under the co-ordination of CMPL staff, both on the surface and underground. This was the key to establishing the new culture in the workforce. The orebodies at CSA Mine are steeply dipping with copper-lead-zinc mineralisation in zones of strong alterations in a fine-grained siltstone host sequence. The predominant economic minerals are chalcopyrite, sphalerite and galena. The major gauge minerals are pyrrhotite, pyrite, chlorite, sericite and quartz. Ore for the project is being developed and mined from two high grade copper lenses within the QTS North system. Chalcopyrite occurs in two forms. The first consists of coarse chalcopyrite grains in association with pyrrhotite or pyrite. The second form consists of chalcopyrite grains intergrown with pyrrhotite grains. This form of chalcopyrite is quite rare. It allows electrochemical interactions between grains, resulting in rapid oxidation of the chalcopyrite surface. Physically this ore looks like, and has been mistaken for æpeacock oreÆ, ie bornite, but is infact oxidised chalcopyrite.

Jan 1, 2000

By I Kolomaznik

Each technological process can be reduced on the transport networks, and namely on the parametric networks and the non-parametric ones. The parametric networks are created by the piping, electrical cables or channels. The non-parametric network is created by the ways, suspended grooves, trackages and also by the belt conveyors or other conveyors for continuous material transport. If we reduce the technological process on transport networks, then, by the creation of these networks models and their mutual interconnection we obtain the model of the whole technological process. The model can be understood as the universal one, without exaggeration, because it is valid for any technological process. However, for us the mining production process is important what represents the mining and transport of raw materials under the support of the ensuring system. In this contribution one of the first attempt is described, and namely how to connect the parametric network which has been already worked out very properly with the non-parametric network what is presented in this contribution by the transport line of belt conveyors.

Jan 1, 2003

The effect of temperature, time and SO2 concentration in the atmosphate have been studied for a complex Pb-Zn concentrate, which contained four sulphides and some organic material, in order to determine optimum roasting conditions. Under static roasting conditions virtually complete sulphation was achieved after roasting at 650¦C.2 hours in 10% SO2 in air. Both zinc ferrite and zinc silicate were observed to form early in the roasting, but continued exposure to SO2 -containing gases caused decomposition of these as the roasting time increased. Water and acid solubilities of iron, silica, calcium, magnesium and aluminium in the calcine were determined, as a function of roasting time, temperature and atmosphere composition.

Jan 1, 1970

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977