Search Documents

By J-P Franzidis

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMCÆs (now BHP BillitonÆs) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

Optimisation of capital in the development process is critical to the profitability of any new mining venture. The process of optimisation should apply to all aspects, that is the financing, management, revenue, reporting and, of course, the development of the project. Unfortunately, too much emphasis has been placed on the optimisation of the financing or reporting aspects and too little on the project itself. This paper addresses the latter.

Jan 1, 1991

By C Smith, D Lilly

The Lafarge Marblehead Plant in Marblehead, Ohio, USA produces 4.2 million tonnes of sized aggregate yearly. In 1997, a program was instituted to maximise primary crusher productivity through the optimisation of blasting variables and procedures. A proprietary blasting shot report database and the Lafarge production database was statistically analysed to provide guidance in the program. Blasting powder factor (kg/m3) was the main control variable utilised to increase crusher throughput. In 2005, the program was refined to increase the production of certain high margin aggregate sizes and the reduction of fines. The principal blasting component affecting the percentage of high margin size production appears to be pattern area (burden and spacing area). This can be coupled with powder factor to optimise the production rate of high margin aggregate sizes. The size optimisation program incorporates the blasting shot report database, Lafarge production database, statistical analysis and aggregate sampling. A preliminary indication is that the production of high margin sizes (12.7 mm X 4.8 mm, 24.4 mm X 12.7 mm, and 50 mm X 25.4 mm) has been increased seven to 12 per cent utilising these techniques. As an added benefit, blasting costs have been reduced linearly as burden û spacing pattern areas have increased and powder factors have decreased. The program is ongoing and will investigate other blasting procedures and variables including electronic blasting caps to further increase the production of high margin products. The statistical methods involved in the analysis are described in this article for use in other mines and situations. The methods described can be used to optimise crusher throughput, digging rates and product size.

Jan 1, 2007

Development of the Greenvale orebody, containing 40,000,000 tonnes of nickel ore, began in 1971 and production commenced in 1974. Annual capacity is 2,800,000 wet tonnes. The variations in ore grade and physical characteristics which occur throughout the ore- body had a major influence on the selection of mining methods, grade control procedures, and equipment. After removal of overburden by scrapers, ore is excavated by draglines sidecasting into windrows. Feed to the crushing plant is .reclaimed by front end loaders into rear dump trucks according to a grade selection pro- gramme. After crushing, ore is stockpiled into blended units of ore of required quality. Ore is stacked and reclaimed for train loading using techniques designed to give maximum mixing of ore characteristics through Bach unit. These procedures are repeated on discharge at the plant site at Yabulu. The railway, constructed by Queensland Nickel Pty. Ltd. to Q.G.R. standard, and operated by the Q.G.R., is 216 km long and includes eight major bridges and three tunnels. Two trains per day, one of four locomotives and 92 waggons, and one of three locomotives and 69 waggons, haul crushed ore to Yabulu. Train loading is semi-automatic. A small township and associated services have been constructed for employees at Green- Vale.

Jan 1, 1974

By M Pizey

After 60 years of operation, coal extraction at Solid Energy New ZealandÆs (SENZ) Strongman Mine, near Rapahoe is scheduled to end in early 2005. Up until 2003 the closure bond for Strongman Mine was only $930, and both SENZ and the West Coast Regional Council (WCRC) agreed that a more realistic level of bonding was required.   A conceptual closure plan has been developed by Golder Associates, and the cost of the work estimated. Closure includes decommissioning of equipment and facilities, rehabilitation and replanting of all disturbed areas and a period of maintenance and monitoring to verify that closure objectives have been met. Significant maintenance allowances are included to cover management of underground fire, subsidence and slope instability. These make up much of the potential ongoing environmental liability at the Strongman. All costs incurred beyond year 1 of closure are discounted to present value. Uncertainty in costs is addressed by Monte Carlo simulation, with an 80 % confidence level adopted.   A bond quantum of $3.0 million has been calculated for the first year of closure at Strongman. A three-year ærollingÆ bond is proposed. Progress will be reviewed annually, with the bond adjusted up or down accordingly. It is then renewed for a further three years. This allows for progressive return of the bond as rehabilitation objectives are met and verified. Similarly, if there are delays in meeting objectives, a proportion of the bond may need to be kept in place for a longer period than assumed. The level of bonding in place for the Strongman operation at any time in the future will therefore reflect the cost to complete the closure work programme.

Jan 1, 2004

The methods used by the Anglo American Corporation for analysis of long-term metal markets and prices are described. The principal factors affecting the relationships between production costs and metal prices are analysed. These are firstly the type of market, - speculative or consumer commodity, free market or subject to price control; and secondly the rate of growth of demand for the metal. It is shown that virtually all metals will have relatively low rates of demand growth for the foreseeable future, due to market saturation, increased economisation, substitution and product obsolescence. Metal prices have a clear dependance on production costs, however forecasting future costs is by no means simple; amongst other things, account must be taken of changing exchange rates, inflation rates, and the potential for operating more efficiently. The paper concludes by giving brief assessments of the long-term future for aluminium, copper, zinc, nickel and tin.

Jan 1, 1986

By Keele R. A

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

By Brant BA, Lewandowski R, Trendle M, Haughton D

There is a vast amount of geotechnical data, which can be obtained during exploration programs at new and existing mine sites. Additional information on the performance of the in-situ rock mass can be obtained from bore cores, which are usually only geologically logged and then stored. A computer based data management system for storage and retrieval of geotechnical data has been developed to access and manipulate such data.

Jan 1, 1983

By Staude W, Rosser A

Due primarily to the publication of the Fitzgerald Report the impact of taxation on the mining industry and the amount of taxes actual- ly paid by the industry have become items of intense debate. However, the discussion has been governed more by impassioned rhetoric than considered logic. It is equally as wasteful to the economy for the mining industry as a low cost efficient export earner to be punitively taxed, as it is for the industry to be given excessive taxation assistance. A comparison of the effect of five tax- ation policies on the cash flow of a capital intensive mining project is presented. The policies considered are Liberal 1969, Liberal 1976 with and without the coal levy, Labor 1975 and Labor 1976. The mining project used in the analysis is modelled on published estimates for the proposed Nebo coal project. The analysis is equally applicable to any large mining or petroleum development.

Jan 1, 1977

In this paper presented are the criteria used when assessing the harmfulness of shocks affecting the buildings. Those criteria are based on the value of speed or accelerations of building vibrations. Presented is the scale of harmfulness of vibrations of Langefors and Kihlstrom, Bureau of Mines, and SWD contained in the Polish Norm PN-85/B-02170. The parameters of the mining shocks measured by the Lubin coal mine station were compared with the parameters calculated as per the correlations (regression curves). The average acceleration calculated from the correlations for eight measurements is only two per cent higher than the actual one. But the average frequency of vibrations calculated from the correlations for eight measurements is as much as 2.22 times lower than the actual one. In order to analyse whether that takes place in the whole range of the energy of shocks compared were the results of calculations from the correlations for various magnitudes of shocks and various distances from their epicentre with the results of the measurements. From that it follows that only for the shocks of the highest energies the lowering of the frequency of vibrations by two times causes movement from the higher zone of harmfulness to the lower one (for example from the IV to III). In the one-family houses in Lubin there were the damages that are characteristic for not only for the III but also for the IV sphere of harmfulness as per the SWD scale. That should be explained via further research and maybe it would be feasible to draw out a new correlation to determine the frequencies only for high values of energy of shocks and determine the preciseness of the acceleration and frequency correlations used presently.

Jan 1, 2003

By C G. Ferguson, S L. Makin

The Cawse nickel project is a new generation pressure acid leach (PAL), solvent extraction and electrowinning process used to produce LME grade nickel metal and cobalt sulphide concentrate containing 40 per cent cobalt by treating nickel and cobalt oxide ores from a lateritic ultramafic profile. The project is located 50 kilometres NW of Kalgoorlie in Western Australia. The commercial success of the Cawse nickel operation is dependent in part upon the ability of the principal ore type to be beneficiated. A simple process of rejecting lower grade material on the basis of particle size achieves this. The process is called upgrading and allows subgrade material to become commercial ore grade and also allows higher ore grades to be processed in the early parts of the operation. The success of the upgrade process is dependent upon the physical and chemical properties of the ore being processed and the nickel grade of the ore. The upgrade ore type represents >80 per cent of the Cawse nickel resource and is hosted mostly within a limonite unit, represented by goethitic clays in the upper saprolite zone. In the upgrade processing circuit the ore is crushed and slurried. It is then passed over a series of screens that remove all material over 0.5 mm. This ensures that coarse material is removed from the main ore stream. Upgrade is reliant on selectively rejecting lower grade or barren material, which can include silica, magnesite and relict saprock. To predict leach feedgrade, the grade control estimates the head grade and upgrade percentage for all ore delivered to the run of mine ore pad. To do this reverse circulation (RC) drill holes are logged for ore type, assayed for a range of elements and undergo simulated upgrade testwork. The percentage and grade of material rejected through the upgrade circuit has the most influence on upgrade per cent. This reject is determined by the physical properties of the rock mass and drum scrubber parameters. The correlation between nickel upgrade and reject can be established to predict upgrade from the known mass reject. Parcels of upgrade ore milled to date closely follow projected correlation trends. Upgrade circuit results have been excellent, with average nickel grades upgrading by 34 per cent, cobalt by 23 per cent, with 55 per cent mass passing.

Jan 1, 2000

By Peck RC

The ore body at Elura contains fine grained galena and sphalerite in a matrix which is mostly pyrite. A differential flotation circuit concentrates lead and silver in the first section and zinc in the second. The lead section, shown in figure 1, was sampled in detail previously and the metallurgical performance assessed on a size by size basis. That assessment took no account of liberation and given the fine grained nature of the ore body, this could lead to an incomplete picture of the flotation performance. Liberation measurements were made using the QEM*SEM system on four size fractions of samples taken from seven different streams in the lead section. Using the mineral flows obtained from the mass balance around the lead section an excellent liberation balance was obtained which enabled the effect of liberation on the flotation performance to be assessed. The measurements indicated that only 17 per cent of the galena and 28 per cent of the sphalerite in the flotation feed was liberated. On the other hand 31 per cent of the gangue iron sulphides were liberated. The final concentrate was largely composed of locked galena and locked iron sulphides with 85 per cent of the product being locked. There was a small but significant fraction of liberated pyrite.

Jan 1, 1991

In 1939 at the annual meeting of the Australasian Association for the Advancement of Science, held at Canberra, a paper was contributed by E. de C: Clarke and H. A. Ellist in which a plea was made for more "facts" concerning metasomatism near ore-bodies in Western Australia. From time to time writers here, and in other parts of the world, have discussed the alterations in wall rocks of various reefs and lodes, but little has yet been attempted in the matter of accumulation of quantitative data, both chemical and mineralogical, and in the correlation and comparative study of this data. Such a detailed comparative study is needed to determine the economic value of a practical application of our accumulated knowledge of the phenomena of metasomatism.When in 1939 the opportunity offered for an examination of the core from 4 bores recently put down by the Big Bell Mines Ltd., to explore the ore-body of the Corinthian G.M. 10 miles N.W. of Southern Cross, Western Australia it was hoped that some small beginnings might be made of an accumulation of comparative and quantitative data regarding the metasomatism of the wall rock immediately adjacent to this ore-body.By the courtesy of the Big Bell Mines Ltd., the core from the 4 bores was delivered to Survey Headquarters, Perth;in the middle of June, 1939 and copies of assay plans of part of the underground workings at Corinthian, and of the results of assays of the bore cores, were also supplied by the management of the above company.It was not, however, until March, 1940, that it was 'found possible to investigate the core. At that time the writer's colleague, Mr. R. S. Matheson, conducted a: megascopic examination of all the bores and selected material from two of these for possible future chemical analyses. Late in 1940 the writer commenced a microscopic petrological examination of this material.AIM OF THE INVESTIGATIONThe object of the petrological part of this investigation was to determine whether from a megascopic and microscopic examination of the core, any evidence could be obtained indicating changes, in mineralogical composition...

Jan 1, 1942

By Selby DW, Hamill J, Cauley ID, Thomas I, Thornton AJ

The main objective of sulphide flotation in a cassiterite concentrator is to remove sulphide minerals (pyrite, pyrrhotite and sometimes chalcopyrite) from the ore prior to gravity concentration. Tin losses in the sulphide flotation stage account for a significant proportion of the total tin loss. separate studies of the sulphide flotation circuits of Renison Ltd and Cleveland Tin Ltd were conducted to investigate reasons for the tin losses. Sampling surveys were conducted in the rougher-scavenger and also the regrind-cleaner sections of both plants. In both plants, the rougher circuits recover excessive quantities of liberated cassiterite, while recovery of the desired composite cassiterite-sulphide fraction is low. The regrind mills are successful in liberating the composite cassiterite in the rougher concentrate, but at the expense of increasing the proportion of very fine tin mineral. The cleaner circuits recover between 40 and 60% of the cassiterite received, and this is all lost.

Jan 1, 1978

By M Rankin, F Medina, R Verburg

We conducted a preliminary assessment of an extensive deposit of historic tailings discharged over a period of 40 years to the shoreline along a Southern Peruvian coastline. The tailings formed an extensive beach approximately 2.4 km long and 300 m wide. The tailings consist principally of pyrite (37 to 59 per cent), hematite (nine to 20 per cent), magnetite (three to 13 per cent) and quartz (11 to 36 per cent). The present operating company was required to evaluate the feasibility of capping the ocean side tailings deposit, however, given the size of the undertaking and the potential to reclaim residual minerals from the tailings, it was prudent to first evaluate whether capping would in fact reduce the impacts to the marine environment. Therefore this preliminary assessment examined: 1. metals contamination in tailings, shoreline porewater and marine sediments; 2. reactivity of tailings and acid generation potential; and 3. the potential for biological effects from metal contamination in the uplands tailings (solid phase) and beach porewater. Based on mineralogy, column leach studies and chemical results, the upland tailings have a high geochemical potential to acidify and release metals, especially copper, nickel and zinc, should they be subject to oxygenated and aqueous conditions. But, the extreme arid climate results in very low potential for precipitation and virtually precludes the transport of acid drainage reaction products from the upland tailings towards ocean. Wind erosion caused by offshore winds is likely a small source of tailing transport to the ocean. Since some potential exists to reprocess the tailings in the future, capping does not seem justified at present.

Jan 1, 2003

An enormous capital outlay is required to bring a new deep level (¦ 4 000 m deep) Witwatersrand gold mine into production. In addition, future mining methods must cater for rapidly rising working costs of which labour costs make up the largest portion. South African mining engineers are therefore being forced to challenge accepted design and valuation principles when planning these high risk ventures. New mining methods must be sought to satisfy the ever increasing need for productivity improvement. The technological problems posed by such changes cover a wide range of disciplines. Aspects of shaft design and configuration, besides being examined in the light of productivity, must also consider the rock mechanics implications at depth. Mining methods must anticipate and prepare for extremely hostile conditions due to seis- micity and virgin rock temperatures.

Jan 1, 1986

By Filmer AO

In contrast to the '50s and '60s, the period of the '80s and '90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world's R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

By Brown K, Francis D

The Yallourn Open Cut Mine has recently commenced mining operations in the new East Field which will supply the 1450MW Yallourn W Power Station for the rest of its 30 year design life. The authors describe the design and implementation process followed during the rehabilitation of the areas disturbed by works associated with mining in the East Field. One area of the East Field, the old external overburden dump, has been of particular interest and is discussed in detail. A discussion on the fire protection considerations is included as these are critical and often misunderstood as being contrary to good rehabilitation design practice. Finally, the development of a master plan for the rehabilitation of the Yallourn Open Cut in general, incorporating the East Field work, is discussed.

Jan 1, 1992

A comprehensive understanding of the rocks associated with coal seams, and also of the coal itself, is essential in assessing the likely behaviour of the materials before, during and after the mining process. The nature of the rock materials involved in coal mining can give rise to risks from adverse geomechanical properties, create problems in coal quality control and produce difficulties with environmental impacts, all of which may affect the profitability, impact and safety of the operation. Examples of issues associated with rock composition include slaking and degradation leading to roof, floor, pit wall or spoil pile instability, ignition of methane in mine atmospheres by frictional processes, liberation of quartz-rich dusts into ventilation systems, production of coal with unfavourable preparation or marketing characteristics, and escape of suspended solids or potentially toxic leachates from spoil piles and other types of emplacements. Methods for evaluating rock composition include microscopic examination, chemical analysis and X-ray diffraction, with the latter being especially useful for fine-grained rocks or for clay-bearing materials. Other techniques, such as geomechanical testing and down-hole geophysical logging, are also useful, but give less direct information about the actual composition of the materials involved. Indeed, understanding of rock composition, through microscope or quantitative X-ray diffraction studies, provides a basis for checking information from other sources, explaining different aspects of rock behaviour, and an essential link in relating geophysical or geotechnical data to broader-based geological models as part of the risk assessment process.

Jan 1, 2003

The present geology of the northwest quadrant of the Circum-Pacific is the product of the interact-ions between plates or paleo-plates which have oc-curred since the earliest part of the earth's hist-ory. Almost every possible geologic structures are observable there; stable continents, collision belts, and subduction arcs as well as extensional basins. This suggests that almost all the possible tectonic processes occurred through geologic time and the present overall structure of the Quadrant is no more than a time section of the long lasting tectonic history which the region experienced.

Jan 1, 1990