Search Documents

By Harris HR

This paper documents the selection, installation and performance of six, seventeen cubic metre, Dorr-Oliver flotation cells for primary zinc flotation at the North Mine in Broken Hill. The cells were installed to replace fifty, small cells, and despite initial design problems, have per- formed satisfactorily.

Jan 1, 1988

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

The safety in pillar extraction is closely allied to the design features of the pillar extraction system. Considering the conventional supported systems of pillar extraction there are problems associated with complying with the design system outlined. The accident causing agencies and the legislative action to overcome them are im- portant aspects. There is merit in the regularity of support and the limiting of the effects that human error can cause. But new problems and hazards are introduced by this powered support equipment. The comparison of accident experience is difficult due to lack of records and lack of uniformity of approach, but it is clear that powered supports provide a safer system. Every progress in research and practice provides further data to employ in accident prevention.

Jan 1, 1974

By M Brooks, M Nelson

A fundamental study was carried out on super pit sulphidic gold ore to establish the most influential flotation characteristics which were subsequently used in the development of an optimum flowsheet to achieve best economical recovery of gold. In developing the flowsheet, consideration was given to existing operational constraints in the treatment of the Super Pit ore. The fundamental study also included an innovative diagnostic investigation to establish the location and value of gold in the major mineral assembly of the super pit ore from a metallurgical rather than a mineralogical perspective. This study mapped a metallurgical fingerprint of the major types of super pit ore in relation to the location and association of gold.

Jan 1, 2000

The sudden. explosion of relatively inexpensive digital process control computers has accelerated interest in the possibilities of economic savings by their use. In particular the metalliferous industries have shown that they are willing and capable 6f grasping this new technology and putting it to good use. These industries have a number of problems which need special attention. In many cases the process is difficult to measure and a reaction is often controlled by measuring a secondary effect, computing its relationship to the reaction and then applying the necessary corrective action. This creates problems in building the process model, designing the computer to process interface and in the subsequent system development. Environmentally the metalliferous industries create conditions which severely test sophisticated electronic equipment. Care taken in locating and housing this equipment is a major factor in ensuring reliability in Operation.

Jan 1, 1977

The basic methods to remove material from underground mines are to: convey continuously, batch in trucks, or batch in a shaft hoisting system. A critical aspect in shaft hoisting is accurately batch loading the conveyance or skip. During the 20th century, the almost universally accepted method of loading was via a measuring flask. A measured quantity of material was filled into the flask as the conveyance traveled through the shaft and then, when the conveyance arrived at the loading position, it was ædumpedÆ into the skip for hoisting. Two skip loading conveyor systems have been developed in Australia: BHP BillitonÆs Cannington Hoisting System, installed in 1996, is believed to be the first conveyor loading system designed for two skips. Two parallel conveyors were installed with a two-way gate controlling feed onto each belt. Cannington was ideally suited to conveyor loading as the very high ore density and relatively low production rate required a relatively small volumetric storage capacity on the weighed belt. Newcrest MiningÆs Telfer Hoisting System, which is to be commissioned in 2005, consists of a single slewing conveyor loading each skip with 32 tonnes of ore. The development of this system eliminates the two-way transfer, improves the accessibility and minimises the excavation required. While every hoisting system must be considered on its merits, conveyor loading offers significant advantages to the Mining Industry in the 21st century.

Jan 1, 2005

By M McCarthy

Attraction, recruitment and retention of quality mining engineers is becoming increasingly difficult for many mining companies. Part of the problem is attracting young professionals, especially given the decline in graduating engineer numbers, and the other is balancing the new engineerÆs development with business needs. The evolution of the graduate program at Olympic Dam over the last five years has resulted in substantial benefits for both the engineer and the company. The program has developed to provide structured exposure to key areas of the mine enabling new engineers to step into vacated roles as the need arises. The pool of quality engineers generated by the graduate program is a buffer against high industry turnover and helps reduce future recruitment expenditure. Olympic DamÆs program goes beyond conventional recruitment of graduate engineers. Innovations designed to improve intake include the employment of graduate engineers as well as final year students, retraining of existing personnel from other backgrounds and fast track recruitment for previous vacation students. By employing a cross-section of professionals to complement the generic university graduate, the company takes full advantage of the relevant lifestyle experience belonging to the individual, which is a substantial factor in turnover. Study assistance and a salary paid for final year students and mature age students often creates a loyalty that lasts beyond graduation. Careful selection of vacation students increases the ease of recruitment at a later stage and ensures that full advantage is taken of the relationship developed previously between the company and young professional. The evolution of recruitment at Olympic Dam has seen a decline in the turnover statistics of young mining professionals.

Jan 1, 2005

By S M. C Verryn

The amount of raw material used in the production of cement can be reduced by partially supplementing it by pozzolanic waste material without changing its properties negatively. This paper discusses results of an investigation using slag from the Pt industry, from the production of steel using Midrex processes as well as fly ashes from different coal power plants in South Africa. These are blended in a 20 per cent slag or fly ash to 80 per cent cement ratio. The properties of the mixtures depend on the phase composition, chemistry, grain size and the sources of the materials. The results are promising, but show variable behaviour depending on slag and cement composition. Compressive strength tests as well have heat flow curves showing the hydration behaviour, indicating that 20 per cent addition of slag or fly ash to ordinary Portland cement is viable. There is a large potential to use slag in cement mixtures and this study can be used to develop cements that will positively influence CO2 emissions and help to reduce large slag and fly ash stockpiles.

Jan 1, 2008

By Ho-Tun E, Stewart PSB

The definition and recognition of silver minerals is very difficult. In general such minerals occur at low concentration and can be hard to identify and measure using conventional optical mineralogy. The present paper describes the use of the QEM*SEM system to tackle this problem and provide information of use to the metallurgist. Three aspects of QEM*SEM are used to special advantage in this application. Firstly the automated mode of operation is used to make a rapid search for the sparse phases. Secondly the X-ray capability is used to identify the mineral phases. Finally the image analysis programs quantify the distributions of the minerals which are found. The paper deals with the identification stage of the process and with the use of the data which can be derived. Silver minerals which covered a range of ore types and composition were collected and studied in detail. On the basis of these measurements and information received from a number of mining companies regarding the important minerals, a classification table was prepared. This table listed about 40 different silver mineral types which could be identified by QEM*SEM and which were of interest in silver recovery processes. Where the silver occurs in solid solution in concentrations greater than about one per cent, the silver content in the species was subdivided into ranges based on statistical intervals. The QEM*SEM system was programmed to recognise these as separate species. Examples are presented of the use of the system in defining the type and morphology of the silver mineralisation to assist in the assessment of batch flotation test Samples.

Jan 1, 1993

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

By Roderick W. F

The equipment and procedures used for green pellet production on a laboratory scale are given, together with a description of the straight grate pellet strand analogue which has been developed to examine the response of various ore types to heat hardening. The capabilities of the analogue are illustrated with data obtained from the balling and drying studies using a manganese ore. Differences in inter-batch pellet quality are discussed, and method of minimising the experimental error that can arise from these differences is Presented.

Jan 1, 1974

By Basillo CI

The adsorption mechanisms of various thiol collectors can be subdivided into four classes: chemisorption, EC-mechanism, catalytic oxidation and metathetical substitution. The chemisorption mechanism occurs at potentials below the thermodynamic potentials for the metal-thiol compound formation and is reversible. The EC-mechanism occurs when the mineral is sufficiently oxidised to liberate metal ions to form metal-xanthates; therefore, it is observed with more easily oxidisable minerals and/or with collectors having large pK values. Thionocarbamates adsorb on sulphide minerals via the EC-mechanism due to their large pK values. Although the adsorption occurs at very low potentials as compared to xanthates, it is irreversible with large overpotentials. On the other hand, the adsorption of modified thiophosphates and thiophosphinates occurs near the thermodynamic potentials because of the low pK values. The metathetical substitution is believed to occur only when a mineral is highly oxidised. These classifications are useful for studying the effects of electrochemical potentials and the molecular structure on the collector adsorption Mechanisms.

Jan 1, 1993

Conveyor belt haulage offers the advan tages of continuity of operation, minimum labour requirements, and the ability to handle large volumes of material over extended periods. However, breakdown of critical con- veyors in the system can cause undue and substantial losses in production output at the working faces, unless adequate surge bin capacity is incorporated in the haulage system. A conveyor belt simulation programme, code name 'Beltsim' was developed by Bucklen et al (1968) at the Virginia Polytechnic Institute in the U.S.A. and provides a quantitative measure of the performance of a conveyor belt network design. A limitation still exists with the computer programme and involves the inability of the programme to predict the necessary surge bin capacity to overcome conveyor belt downtime. The computer programme was modified to overcome this limitation, to simulate a con- veyor belt breakdown, and to provide a quantitative prediction of the surge bin capacity necessary to permit a modern mining system to operate effectively and continuously.

Jan 1, 1977

In a coal mine there are many substances capable of ignition under certain circumstances, which can be placed in the following groups: ordinary combustible solids, dusts, liquids and vapours, gases, metals and plastics. There are many factors influencing ignition, including temperature, minimum ignition energy, particle size, explosion pressure level, rate of pressure rise, specific energy content and also explosive limit. Not all are applicable in every case. Frictional ignition of methane is an accident statistic of increasing concern and is considered in some detail. Practical measures that can be taken to reduce the incidence of frictional ignitions are considered, and also possible ways of ignition suppression.

Jan 1, 1981

Seven papers included in Session 8 of the Third International Mine Water Congress under the heading "Achievements in Mine Water Management & Research" have been reviewed. Only one paper, a case study by Masters on biological treatment of inorganically polluted effluent, has any connection with research in the sense of seeking new, generally applicable knowledge which would advance the frontiers of mine water management. The remainder deal with various aspects of the management of mine water ranging from investigation of the geology of a specific aquifer system through operating dewatering systems to the management of specific effluent disposal problems.

Jan 1, 1988

By Hunsaker R. D

The description, characteristics, advantages and application of a new bulk explosive for medium to large diameter dry blasthole conditions is described. A brief outline of the delivery system for the product is also included. This explosive has been designed to provide an alternative to ANFO, currently the most common bulk dry hole product available to the mining and quarrying industry. The selection of the optimum explosive for any blasting operation is of prime importance. It is a major factor contributing to the production of the desired results in terms of muckpile fragmentation, shape and diggability. The optimum explosive can be defined as the most cost-effective in producing satisfactory breakage and displacement of the material. ANFO satisfies this prerequisite for a significant proportion of dry hole applications. This unique, low density and low velocity of detonation explosive has been developed to provide the industry with a cost competitive alternative to ANFO. Typical loading or average inhole densities nominally range between 0.40 g/cc to 0.70 g/cc, depending on the application. Characteristics of this explosive allow for specific and common applications in open cut coal and metalliferous operations. These include ore/waste control operations, prestripping and presplitting applications, sites confronting cap rock problems, and large hole diameter quarries.

Jan 1, 1995

Modern minerals projects face serious challenges in earning and maintaining acceptance by their key stakeholders. Factors which underpin effective response to managing these challenges include consideration of public affairs issues from the earliest planning stages, building robust alliances with a range of influential partners, developing a level of transparency in all operations and decision-making and integrating activities towards resolving key strategic issues. Effective community relations is vital and there are a number of elements common to the best approaches. These include senior management support and involvement, appropriate involvement in project decisions and activities by community members and company responsiveness to community expectations. The project's operations manager and executive team must fully commit to developing the capability and processes to meet these challenges. They require a whole of project response and it is not an option to manage them peripherally.

Jan 1, 1997

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000