Search Documents

The Mt Sinivit gold project is located approximately 50km SSW of Rabaul in the Baining Mountains of the Gazelle Peninsula, East New Britain Province. The deposits were discovered in mid- 1983 and form part of a larger 26km long zone of variably aurif- erous quartz veining. There are no surface indications or previ- ous records of any prospecting activity or production from the region. The Mt Sinivit deposits consist of a series of oxide and sulphide reserves and resources contained in the Wild Dog (South- ern, Central and Northern oxide zones; Northern sulphide zone) and Kavursuki veins. The proposed exploitation of the oxide reserves by a series of small-medium sized open pits has been fostered by the PNG Department of Mining & Petroleum (DMP) as part of a government policy to encourage the development of a small-medium sized mining industry in the country. The aim of this paper is to document the steps and procedures involved in obtaining the grant of a Mining Lease emphasising the time and the expenditures required during each step of the approvals process for the Mt Sinivit project.

Jan 1, 1997

By B J. van Loggerenberg

The capital cost of major items of mining equipment is very high. The operating cost of such equipment is also high. It is therefore important that such expensive equipment is used productively. To this end mine management uses production data systems and management accounting systems to monitor events and provide data for analysis to enable management to make operating and business optimisation decisions. This could be done better if there was an understanding of productivity in terms of its utilisation and efficiency components. What has been missing has been a methodology to properly account for the productivity of equipment in terms of its contribution in dollars to the costs and profit of the mine. An explanation of the Productivity Accounting methodology will be given. It will then be shown that productivity has two components, that of capacity utilisation and efficiency. These are defined and the dollar contribution of each to costs and profit shown. The efficiency component tracks the effect of proportional changes in input cost quantities used in the mining process as mining production changes. The capacity utilisation component tracks the effect of step changes in the input cost quantities used in the mining process as mining production changes.

Jan 1, 2003

By T Nixon

A common problem for many mines is insufficient total primary airflow or insufficient airflow in the correct places as the mine changes over its life. This has a number of impacts on the business operation and may result in the need for a major and unexpected capital upgrade of the system, cancellation of a planned production increase, reduction in production targets, increased operating costs, failure to provide contracted metals to customers or acceptance of substandard conditions in the workplace. In some cases, it can even result in premature closure of the mine. In recent times, higher metal prices have given an expected economic boost to many mines, potentially prolonging their life but simultaneously requiring the mine to develop to deeper depths or requiring assets such as shafts and fans to have their service life extended. Insufficient primary airflow is a particular problem in deeper mines as the ventilation circuits become longer, more convoluted, have higher shock losses and the actual airflow requirements increase due to a combination of leakage, dispersion of the workings and the problems of managing the additional heat loads due to higher virgin rock temperatures and autocompression. This paper discusses the reasons why mines experience unexpected shortfalls in primary ventilation capacity with its associated impacts on metal targets, profits and frequently on the health, safety and morale of the workforce, as well as its productivity.

Jan 1, 2008

The gold industry has been revolutionized in the last decade by market forces and technological changes. The latter are discussed in this paper, with particular emphasis on carbon-in-pulp (CIP) and heap leaching. The nature and scope of the process development aspects of a gold project are considered, and factors which determine process decisions are outlined, including the choice of CIP versus carbon-in-leach (CIL), agitated leaching versus heap leaching and treatment of ores containing copper and silver. Likely directions for development of gold processing in general are discussed, and metallurgical process options for treatment of ores of platinum group metals (PGM) are outlined.Metallurgical process development for gold and platinum group metals proceeds through a number of well defined stages, with input from various disciplines and information sources. The orientation phase will include preparation of a general project overview; careful consideration of the issue of sampling and sample preparation; characterisation of the resource in terms of ore types, mineralogy, chemical composition; development of appropriate methodology; and development of an understanding of the potential metallurgical unit operations.The process definition phase will be-'directed to development and definition of a notional process flowsheet, and will include identification and appraisal of process options; development of, notional process flowsheets; testing of flowsheets against ore types; ranking of flowsheets; initial engineering, including preliminary mass balances, equipment selection and plant layout; and broad-brush economic appraisal.

Jan 1, 1986

Alaska Native corporations, as representatives of the aboriginal inhabitants of Alaska, control the mineral rights to 18 million hectares of Alaska, approximately 12% of the state. These corporations were established through legislation passed by the United States Congress in 1971 designed to settle the land claims of the Native peoples of Alaska. Twelve corporations, each representative of a specific geographic and cultural region, were established and granted the mineral rights to most Native lands in their respective regions. Since that time the Native corporations have taken an active role in mineral development in the state. Generally through agreements with established mining companies, Native corporations encourage balanced exploration and development of their lands. Substantial mineral potential has been recognized on Native corporation land, which includes holdings in many historic mining districts of Alaska. Several world class deposits have been discovered on Native corporation land, including the Red Dog zinc-lead deposit, which began production in late 1989. The experience of Alaska Native corporations demonstrates that aboriginal peoples can be very positive forces in resource development.Alaska, although remotely located in the Northeast corner of the Pacific Basin, is playing an increasing role as a supplier of natural resources to the region and the world. Most of Alaska's privately held natural resources are owned by the aboriginal inhabitants of the state. These aboriginal inhabitants, now collectively referred to as Alaska Natives, have emerged in the last two decades as having a major international impact in mineral resource exploration, development, and production.

Jan 1, 1990

By Nettle W. H V

THE past few years have seen a considerable expansion of the roasting of blende in Australia. The bulk of this blende is Zinciferous concentrate from Broken Hill and now forms a very considerable source of sulphur for the acid manufacture. It will bereadily conceded that Australian sentiment is in favour of utilising all known potential wealth, especially that won from below ground, as this once disposed of is gone forever. If Australia does not make sulphuric acid from her sulphide ores we may be sure that the purchaser of these ores will do so if in any way possible. It must not be assumed, then, that the difficulties met are mentioned with the idea of undue criticism, but rather to show that, although most of the intial troubles have been overcome, there are still a few to be encountered; and with the hope that comment brought forth will aid in the solution of the problems facing an industry at present little more than in its childhood as far as Australia is concerned.Blende roasting is done in mechanical furnaces of various makes, and mostly without the aid of other fuel than the sulphur in the ore. It will be our aim to touch on the various difficulties in the order in which they occur in the train from furnace to acid plant.

Jan 1, 1926

BHP Billiton Mitsubishi Alliance, or BMA, is AustraliaÆs largest coal miner and exporter, and is currently responsible for around a quarter of AustraliaÆs total annual coal exports. BMA and its predecessors have been part of the Queensland mining scene for around 40 years, developing world-class mines, a port, overseas markets, and an international reputation for quality and reliability. From its production base in QueenslandÆs Bowen Basin, BMA produces a broad suite of coals which are supplied to 73 customers in 24 countries. BMA was formed in June 2001 as a partnership between BHP Billiton and Mitsubishi Development Pty Ltd, under which the two companies share equal ownership and management of eight Central Queensland coal mines û Goonyella Riverside, Broadmeadow, Peak Downs, Saraji, Norwich Park, Gregory, Crinum and Blackwater û and the Hay Point coal export terminal near Mackay. This case study focuses on Peak Downs Mine, which was the second largest open cut mining operation to be developed in the northern Bowen Basin for the original CQCA Joint Venture. The first coal was mined in April 1972 and today, Peak Downs has a production capacity of over nine million tonnes of coking coal per annum. The mine is located 30 km south of Moranbah and 195 km south west of the Hay Point port facilities. Coal is mined by open cut mining methods using six draglines and two truck/shovel stripping fleets for overburden removal. Coal seams are mined using excavators and front-end loaders and 210 tonne capacity coal haulers.

Jan 1, 2007

By B Snook, G Rollinson, R Fairhurst, R Herrington

Nickel laterites constitute a significant proportion of the worldÆs Ni reserves and are considered environmentally friendly alternatives to traditional sulfide resources. Subsequently they are of increasing significance for exploration and production. To be successfully exploited, however, they require an understanding of the relations between mineralogy, texture, grade and recovery. The development of automated quantitative mineralogy can aid in the characterisation of the ores to help improve extraction and processing methods. Recent developments in hydrometallurgy have resulted in relatively straightforward recovery of Ni in silicate (saprolite and smectite) ores. However, the extraction of Ni from limonitic ores is more complex. It requires a detailed understanding of the iron-hydroxide species and other, potentially interfering, oxide and hydroxide compounds. Particularly the relations between the Ni-bearing goethite and Mn, Al and Cr may adversely affect the economic prospects of an ore. Manganese can adversely affect the selective recovery of Ni and Co from solutions but has also been highlighted as a significant potential by-product (cf, Zhang and Cheng, 2007). Aluminium hydroxides can be significant acid consumers leading to an increased expense of extraction (Johnson, Cashmore and Hockridge, 2005). Chromite is resistant to acid attack, but chromium in goethite may adversely affect the dissolution leading to a retention of Ni (McDonald and Whittington, 2008). This study presents an investigation of oxide and hydroxide species in laterites using QEMSCAN« EDS/SEM-based automated quantitative mineralogy. Samples were collected from Turkey (¦aldag), Albania and the Philippines. Particular emphasis has been placed on the development of a quantification for Ni-poor and Ni-rich goethite.

Jan 1, 2008

It is generally known that Charters Towers was discovered by Mosman, Clarke and Fraser in 1871. However, the time was ripe, and these three were barely in front of others. There is one account that prospectors from Ravenswood visited the area months before but decided it was too far from water, and that one of them had told Mosman and party of the find. There is another account that Joe Larkins found the discoverers before they had registered any ground - this may explain Mosman's quick departure for Ravenswood.When the news spread, the rush was rapid, and there was soon a sizeable population: probably too many, as within twelve months the infant settlement was under considerable stress. First, the presiding Gold Commissioners had adopted "unusual and arbitary" interpretations of the Regulations, and many of the miners were aggrieved; Charters, the senior Commissioner, was accused of favouring moneyed interests, and of retiring ill whenever a brawl or confrontation occured. As a result, the law of the field soon became "the survival of the strong". Second, the settlers were, divided on where the main town should be: Millchester, near the water, or Charters Towers near the mines. Third, the discovery of gold at the Millchester Deep Lead in August, 1872 was followed by highly exaggerated accoants in_' the southern papers, apparently fabricated by local business speculators. The resulting rush resulted in hundreds of unlucky prospectors having to return or seek other fields. In that period two men were killed in squabbles over ground. To make matters worse, by October 1872 a drought had set in, water cost three pence a bucket, fodder was scarce, cartage expensive, and the price of crushing ore rose to thirty shillings per ton.

Jan 1, 1986

The paper deals with the taking of soundings in connection with coal mining operations under part of the Pacific Ocean adjoining John Darling Colliery.INTRODUCTIONIn the early days of mining in the Newcastle District there did not appear to be any definite law specifying the limits to which mine workings, other than certain borings, could extend under tidal waters.As time went on, a figure of 120 ft. was fixed as the minimum thickness of strata between the roof of the seam and the sea bottom; beyond this mining operations are disallowed. The laws relating to working coal under tidal waters are as follow:-The minimum width of pillars to be left shall be eight (8) yards and the maximum width of bords or other excavations shall be six (6) yards, but the lessee may at his discretion increase the minimum width of the pillars or decrease the maximum width of the bordsor other excavations so as to increase the general safety.The eight (8) yard pillars shall be left unwrought.In on-road of every pair of Winning-off or leading headings, a bore shall be kept going ten (10) feet in advance for the purpose of foretelling the presence of any fissure, wash-out, open joint, fault, dyke, or otherwise, and all winning-off headings shall be driven atleast one hundred (100) yards in advance of the working bords.The most accurate and trustworthy information shall be obtained by the lessee not only' of the depth and character of the ocean bed, river, lake, or estuary deposit, but also of the strata overlying the coal seam.When working under the ocean, strata shall be bored through and proved a minimum thickness of thirty (30) feet at the face of the leading headings or levels immediately such headings or levels are under the ocean, and...

Jan 1, 1947

By W J. Bruckard

In Australia, ilmenite is produced from beach sand deposits. These deposits contain varying quantities of the valuable minerals zircon, rutile and ilmenite, along with a variety of other minerals. The valuable minerals are upgraded using combinations of gravity, magnetic and electrostatic processing techniques to yield high-grade products. One of the penalty elements present in ilmenite concentrates is chromium, present mostly as chrome spinels. This mineral is particularly difficult to separate from ilmenite, as the properties of the two minerals are very similar in relation to the traditional separation processes. While the deposits which have been treated in Australia in the past have had only low levels of chromium present, many of the newer deposits contain much higher levels of contamination and, thus, there is an increasing need to develop robust processes to separate chrome spinel from the ilmenite. Flotation, which is a unit process with the potential to solve this problem, has surprisingly received little attention for this application. The literature suggests the research effort to characterise the general flotation properties of chromite (chrome spinel with high chromium content) has been extensive and a substantial amount of data is available. However, the problem of separating a small amount of chrome spinel from a large amount of ilmenite requires a different approach to that from separating chromite from siliceous gangue, which has been the main commercial focus of chromite flotation in the past. Much of the work done has been fundamental in nature and the results obtained are fairly inconsistent, as is the testwork completed at batch and pilot plant scale. While these inconsistencies have been attributed to the variable composition of the mineral, there is little evidence supporting this premise. Just as chrome spinel and ilmenite have similar physical characteristics, the flotation response of both minerals is also similar. This paper reviews the literature relating to the flotation of chrome spinel and presents a considered approach to the development of a robust flotation method to separate chrome spinel from ilmenite.

Jan 1, 2001

By B N. Morrison

In all metallurgical plants metallurgists require analyses of the various intermediate products, eg flotation feeds, flotation concentrates, tailings, mattes, slags, etc to monitor the efficiency of the plant processes and for plant control purposes. Traditionally these samples have gone to off-site laboratories and there can be some considerable delay before analytical data are received. On-line monitors have to be used for plant control purposes and these are difficult to maintain and can give poor quality data. Recent technological advances in automation in analytical laboratories now allow a far quicker turn-around time for analytical data so they can be of more use to the metallurgist. Automation, which involves the use of robots and fewer people in laboratories, has the added benefit of providing higher quality data as the possibility of human error and bias is minimised. Differences between conventional manual laboratories and automated laboratories are described. Automated analytical laboratories are now becoming the laboratories of choice for mining companies which require large numbers of samples to be analysed on a 24/7 basis on similar sample types using the same sample preparation methods and analytical procedures. Automated laboratories have now been installed in platinum, iron ore, copper and aluminium producing mining companies. A further advantage to metallurgical plants is now the possibility of siting automated analytical laboratories in-plant and designing the plant around the laboratory. Concentrator streams, slags, etc can be sampled by automated samplers, the samples transferred by automation to the in-plant laboratories and all sample preparation and analyses carried out by automated processes. These laboratories require a minimum of staff. Such automated in-plant laboratories have been installed on a platinum mine flotation plant, a platinum mine smelter and steel plants. One is in process of being installed on an iron-ore mine with the sampling being carried out by an automated sampling tower. The procedures followed in planning an automated analytical laboratory for a metallurgical plant are described in detail in the paper. The platinum plant smelter automated system which includes rapid transport of samples by air-tube to the laboratory for the analysis of the samples by XRFS is also described in the paper. It is concluded that automated analytical laboratories can be retro-fitted to most metallurgical plants but they are best suited to greenfield sites.

Jan 1, 2008

The first steps towards the use of artificial intelligence to manage ground conditions have been made. Millar and Hudson (1993) outline the theory behind the use of neural networks in monitoring rock engineering performance.

Jan 1, 1994

By Murdaugh W

The application of photogeological techniques and analysis of more advanced remote sensor images can be a cost and time effective tool in the search for desert placer gold deposits. Examples are given of regional analysis using standard false color composit Landsat images and conventional black and white aerial photography. The examples include identification of sites to sample to evaluate the pathways of .alluvial gold migration and identification of potential sites of concentration. The results of these studies developed an increased number of target areas and exploration in proceeding with promising results. In addition to the development of additional target concepts and identification of specific target areas data useful to evaluation of mineability can also be obtained from photogeological investigation. Some indication at least can be obtained of the existence of duricrusts and salines that may hamper mining. Identification of possible sources of water is another important task in the desert environment. In addition indications of the clay content of the material to be worked is very important because of its economic impact on operational costs and overall recovery. The application of photogeology to these questions is discussed.

Jan 1, 1988

By AUIMM AUIMM

Continuous Improvement The Council of the AusIMM should expedite the introduction of a continuous professional education policy along the lines of that to be proposed to you by David Pollard today. The Education and Accreditation Committee must continually review the training needs of the next generations of mining industry professionals. It should continue to demand and encourage the creation of the schools for the training of such people. The AusIMM could even put greater onus upon university researchers to accredit university post graduate degrees.

Jan 1, 1994

The Mt. Sisa Orebody on Misima Island, P.N.G., consists of gold-silver mineralization associated with massive carbonate and amor- phous iron-manganese oxides in fractures and breccia matrix. The orebody forms the north- ern extension of the Umuna deposit. The mineralization lies within the three kilometre strike length of a northwest trending, 300 metre wide, high angle fault zone. The fault zone structure is deeply oxidi- sed, with the manganiferous oxide material resulting from oxidation of carbonate. The wallrocks are metamorphosed basement psammopelites and basic volcanic rocks, exten- sively intruded by microgranodiorite. These are dominantly epidotized and sericitized. The precious metals are associated with anomalous Cu, Zn, Pb, Mn, As, Ba, Ga, Sb, and. Mo. Many of the features of the Mt.Sisa mineralization are characteristic of volcanic- hosted epithermal deposits of western North' America. Lithologic and textural gradation is ob- served between the carbonate hydrothermal breccia-fill at Mt. Sisa, and the quartz domi- nated dilational fracture-fill mineralization which forms most of the Umuna deposit to the south. This gradational relationship is ana- logous to that within the Amethyst-OH vein system at Creede, Colorado, where it is shown to be indicative of deposition from laterally migrating fluids.

Jan 1, 1987

On account of the increased work required from the assay office, owing to the large additions which have been made to the smelting and superphosphate plants during the last few years, it was found necessary to build a more extensive and up-to-date assay office than the one that had been in use since the starting of the works some twenty years back.A site was chosen adjacent to the main office, so as to be free from smoke and dust.. The building is constructed of red brick, the over-all dimensions being 109 ft. x 37 ft. The roof is of fibrous-cement slates, 31 ft. high, with a two-to-one rise, and overlaps the walls to the extent of 4 ft. 6 in. on all sides.Special care was taken to give light to all working benches, fume cupboards, and balance rooms. The main chemical room occupies the entire western end of the building, and the fire room the entire eastem end. Between these two rooms are the superphosphate, refinery, and gold-parting rooms on one side of the central passage, and three balance rooms, general office, and cloak room on the other side. The height of the roof affords ample space above these central rooms for storage purposes, and also maintains a fairly even temperature. The ceiling of the main chemical and fire rooms is carried immediately under the slates, which gives a total height in the centre of about 25 ft.

Jan 1, 1918

By L Abrahamsson

The aim with this paper is to discuss experiences from the ongoing research project ‘Attract: A roadmap to attractive, inclusive, and safe mining workplaces’. The project’s aim is to analyse possibilities, effects, and consequences of the green and digital transformation in the Swedish mining industry from workplace, socio-technical and gender equality perspectives. The research project (2022–2025) at Human Work Science at Luleå University of Technology is financed by the strategic innovation program Swedish Mining Innovation (a joint venture by the national research funds Vinnova, Formas and the Swedish Energy Agency). The project includes a multidisciplinary research group of five senior researchers and five PhDstudents and a broad repertoire of methods, eg literature reviews, qualitative interviews with both managers and workers, workplace observations, workshops, surveys, and project seminars where the researchers and the company representatives together analyse the results. One important part of the project is the applied approach where the researchers work together with two mining companies and one subcontractor company. The project has two parallel main subprojects.

Sep 1, 2024

By Abdulhadi H. M, Soliman S. A

The Western Desert of Egypt is a part of the arid Great Sahara of Africa which extends from the Nile Valley in the east to the Atlantic Ocean in the west. It is covered by a sedimentary sequence of Mezozoic and Teriary rocks. Recently this part of the country (about 65% of its surface area) has attracted an increasing attention in the plan of finding new agricultural and industrial communities outside the crowded Nile Valley. The plan aims to reduce the high population density in the narrow Nile Valley and to cover a considerable part of the increasing food demands in the country of Egypt. Accordingly, the groundwater exploration work in the Western Desert has been remarkably increased in the last decade, however it is still limited compared with the vast area of the Desert. The present work is a part of the groundwater exploration in the 6th October City, a new community located at 40kms west of Cairo. The rock exposures belong to a sedimentary stratigraphic section starting from the Cretaceous in the east to the Pliocene in the west. The Cretaceous outcrops due east are attributed to an almost N-S uplift and forms a thick massive limestone plateau which separates the present area from the Nile Valley. The Teriary section in the west have alternations of different porous formations such as the sands and sandstones which may acquire a good potentiality of groundwater resources. The previous groundwater exploration work included combined geological and geophysical investigations followed by exploration drilling. Although the area lies directly to the west of the Nile Valley, the discovered groundwater is saline and located at deeper reserviores compared with the groundwater in the Nile Valley. This groundwater was described as marine fossile water by the oil companies working in the Western Desert. From the geological point of view, it is believed that the Cretacious massive limestone plateau, in the east, roots to a depth which far exceeds the groundwater levels in the Nile Valley and acts as an impervious barrier between the aquifers in the Nile Valley and the area under investigations.

Jan 1, 1988

By Majorkiewicz A

Engineering of gold treatment facilities complete with infrastruc- ture in a remote location such as Papua NewòGuinea present unique problems to the design team. Site location, topography, ground conditions and infrastructure are some of the major hurdles to overcome when setting out on the design of such plants. This paper discusses two such plants, located in two distinctly different areas of Papua New Guinea and the solutions evolved in order to design successful operating facilities.

Jan 1, 1991