Search Documents

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

By J. Warner, K. A. Hughes, P. E. R. Blanchard, J. Esslifie-Dughan, J. W. Reid

Tailings management plays an important role in reducing the environmental impact of Orano Canada’s uranium mining operations in Northern Saskatchewan. Uranium ores mined from Northern Saskatchewan are often associated with large amounts (10-20 wt%) of other harmful elements, such as arsenic and nickel. The JEB Tailings Management Facility (TMF) located at McClean Lake, Saskatchewan is designed to prevent potentially harmful water-soluble elements, particularly arsenic, from contaminating the surrounding environment by promoting the formation of water-insoluble minerals. It is therefore important to determine which arsenic-containing mineral species are present in the TMF and how they evolve over time. Researchers at the Canadian Light Source (Saskatoon, Saskatchewan) were successful in identifying the arsenic mineral species present in tailings samples collected from the TMF in 2013 using X-ray absorption near-edge structure (XANES) spectroscopy. XANES analysis verified that the majority of arsenic species in the TMF existed as amorphous and crystalline ferric arsenates with minor amounts of arsenite and arsenide species. Herein, XANES is again used to analyze a new set of tailings samples collected from the TMF in 2018, specifically focusing on the difference in the distribution of arsenic species in old and new tailings.

Jan 1, 2020

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By H. R. Butler, R. N. Browne

"The International Nickel Company of Canada Limited consumes some 33 ½ millions of gallons of fresh water and reuses more than 100 millions of gallons of water daily. The continuing search for suitable recycle methodology has enabled the Company to put one 25,000 TPD mill on line utilizing recycled water entirely and a second 35,000 TPD mill is under construction which will likewise employ the concept of recycled water. Future milling plans are aimed at the replacement of all fresh water with recycled water, including sewage effluent and mine waste water.WATER REUSE AT INCO’s SUDBURY MILLSAs man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive -- W A T E R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the United States was over 300 billion GPD (l) or more than 1,700 GPD per person(5) The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the United States by the year 2000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then can we continue to wreak such havoc on that life-sustaining substance - WATER?"

Jan 1, 1970

By H. Lundberg

Introduction The world has been suffering from an excessive production of all kinds of raw materials, and the metals and petroleum are no exception. As a consequence, at the moment, the urge to find new mineral deposits is almost non-existent and prospecting languishes. But from previous experience we know that sooner or later new supplies will be needed. Mineral deposits become exhausted, and to keep up the supplies of our metals and petroleum, new deposits must be found. Even now, a supply of petroleum of domestic production would not be unwelcome in Canada. It is not, therefore, so entirely malapropos to discuss means of finding ores and oil as it would seem. Almost any physical property connected in definite manner with minerals and rocks may be made the basis of geophysical exploration. This is particularly true of electrical resistivity, and its utilization in electrical prospecting has been the deciding factor in the discovery of such big ore-bodies as Buchans mine, Newfoundland, and the large copper ore-bodies in northern Sweden, etc., as well as in the solution of many foundation and structural problems. The importance of electrical prospecting has been growing steadily, and already there exists hardly any exploration project involving geological problems which may not profit by its application. Electrical prospecting is marching on, and neither temporary failures, nor incompetence, nor over-optimism, nor ill-will and pessimism, nor bad times and business depression, will be able to halt its progress.

Jan 1, 1931

By Axel Doelcken

?? Liebherr excavators in standard configuration are generally designed to operate in an ambient temperature range between -12°C and +55°C (10.4 °F and 131°F). ?? To operate effectively and efficiently in very low temperatures special consideration needs to be given to the design ??An inappropriately designed hydraulic system unable to withstand extreme changes in temperatures or varying working conditions will lead to: - premature wear and more frequent replacement of components - increased maintenance & unplanned downtime This will affect productivity & operating costs.

May 1, 2008

By The Staff

FOR forty years cyanide men have been intensively engaged on the treatment of sulpho-telluride ores. So far as we know, the processes used today were-with the important exception of the concentration plus high-lime process at the Victor mill (1915)-in use, or had been tried, in the earl y years of the century. Roasting, bromocyanide, ordinary cyanide, table and vanner concentration, floating and treating the concentrate, roasting con-centrates prior to treatment, etc., all were used at Kalgoorlie in 1904 or earlier. Flotation, followed by shipment of the concentrate to the Golden Cycle mill, was the practice at the Vindicator mine, Cripple Creek, for some years prior to 1917. Similar practice was employed in the Portland Independence mill at Victor, Colorado, and was lacer superseded by the table concentration, high-lime cyanide treatment of rails of the older Portland Victor mill. During all this time, an immense amount of research was being clone on these ores by the staffs of numberless companies. Conclusions were drawn and mills built. But if the results of one per cent of this research were ever published in sufficient detail for intelligent use by others, the Lake Shore staff has been unable to discover them, or does not recall having clone so. Government laboratories-as for instance chose of the Mines Branch, Ottawa, in or about 1927-have touched upon certain methods in their publications, but they simply have not had the time to finish the job. The paper by W. E. Johnston, Tellurides-Problem or Alibi? (E. & M.]., Aug., 1933), aroused wide interest and comment. It published conclusions, some right and some wrong, and gave the evidence adduced by the author i:n support thereof. Conclusions published without supporting evidence are to most of us worse than no conclusions at all. We suggest chat, if even one-tenth of the operators had published full, detailed results of their laboratory work, ad vance in the treatment of sulpho-telluride ores would have been very much accelerated. Therefore, we venture to inflict upon the Institute a compendium of the results of laboratory work performed during the past few years at the Lake Shore mill. It is really a summary of the more interesting results to date, prepared by the mill staff for their own use and benefit. But we hope chat the discussion under any heading is so detailed chat it will be intelligible to anyone interested in that phase of the subject.

Jan 1, 1936

By F. P. Morawski, J. E. Schelske, J. R. Geddes, B. R. Eberts, D. M. Wilson, J. D. Jeffries

"The Griffith Mine is located 200 miles northeast of Winnipeg and is 30 miles south of Red Lake, Ontario. Owned by The Steel Company of Canada Limited and managed by Pickands Mather & Co., it has an annual rated capacity of 1.5 million tons of high-grade iron ore pellets with an analysis of 66.3 per cent iron and 4.5 per cent silica.Development of the mine and construction of the plant got underway in January of 1966 and operations began in February of 1968. The orebodies outcrop on the shore of Bruce lake and run under the lake. The ore in its crude form is a metasedimentary low-grade magnetite and occurs in a highly folded banded formation. The average iron analysis of the crude is 29 per cent and the over-all weight recovery is 32 per cent.In order to mine the portion of the orebody under the lake, the soft varved clay on the lake bottom was hydraulically dredged and a dyke constructed of rock, with till used to provide an impervious seal on the lake side of the dyke, prior to dewatering.Mining is carried out by conventional open-pit tech-niques. Ore dressing is achieved by combining one crushing stage and a two-stage grinding system, with beneficiation by magnetic separation, hydroseparation and flotation. Agglomerating is done with conventional balling drums and pelletizing is carried out in shaft furnaces.Of interest and discussed in detail are the 32-foot autogenous cascade mills ."

Jan 1, 1970

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By Fidelis T. Suorineni

The Ashanti mine, located in Obusai, Ghana, West Africa, has been in production for over 100 years, and is currently the second largest single gold producer in Africa. The mine covers a concession area of 434 square kilometers with four main ore types: the quartz vein type, disseminated sulphide type, supergene sulphides and transition ore, and granitoids stock works (visible gold and quartz veinlets). Various mining strategies and methods have been employed for the mining of the narrow-vein ore at Ashanti. In recent years, the mine owner: Ashanti Goldfields Company Ltd. has embarked on a mine-wide expansion program to boost production to a target of one million ounces per annum. With the rapid depletion of its high-grade ore, a suitable mining method was required to produce a high tonnage at low cost to meet production objectives. This paper discusses how the Ashanti mine applied Canada experiences in mining technology to boost production, and the impact that the differing geological settings between the two countries had on the stope performance at the Ashanti operations. Experience developed at the Ashanti mine led to innovative modifications for stope layout and design methods in relatively poor ground conditions.

Oct 1, 2001

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By Gyan S. Rajhans

"The strategy of fibrous dust sampling is discussed, various sampiing methods are critically reviewed .and their application to coal dust is demonstrated. Fibre counting is described in detail. An attempt is made to explain the basis of determining the threshold limit value of asbestos and other dusts. The paper also discusses such dust control methods as enclosure of the process, effective local exhaust ventilation, segregation, substitution, wet processing and continuous monitoring of the return air for recirculation."

Jan 1, 1970

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM's structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By Yihan Liu, Jintao Zhang, Chen Xiao, Xiaomeng Zhao, Guanglei Song

To estimate the performance of the inert anode materials based on NiFe2O4 spinel ceramic during it used for aluminum electrolysis, we investigated the wetting process of cryolite molten salt which is in composition of industrial aluminum electrolysis with carbon anode and NiFe2O4 based cermet materials, by means of determination the interface wetting angle between the molten cryolite electrolyte and the solid anodes interface. The results show that the wetting angle between the electrolyte and carbon anode is larger than 90 angulation, this means that they basically can not wetting; however the nickel ferrate spinel ceramics behaves much better. In regard to the NiFe2O4 matrix materials, their initial wetting angles is 76.9. The initial wetting angles for 1.0wt%MnO2, 2.5wt%TiO2 and 0.5wt%V2O5-doped samples are respectively 56.86°, 52.98° and 51.93°. However, after 50s later, all the wetting angles came down below 15°.

Jan 1, 2015

By Ian R. Morrison

"Abstract - The Izok Zn-Cu-Pb-Ag volcanogenic massive sulfide deposit is located 265 km south of Kugluktuk (Coppermine), Nunavut Territory, Canada, in the west-central Slave structural province. The Izok deposit is owned 100% by Inmet Mining Corporation and represents one of the largest undeveloped zinc-copper resources in North America. The Izok deposit is hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks of late Archean age. The hanging-wall stratigraphy includes additional felsic volcaniclastic rocks, andesitic and basaltic flows, thin sulfide-rich iron formations, and turbiditic sedimentary rocks. The felsic volcanic rocks are intruded by intermediate dikes and sills, followed by gabbroic dikes and sills. Both intrusive suites are interpreted to be volcanic feeders to the overlying flows. All lithologies are subsequently cut by younger, irregular, granitic pegmatite and diabase dikes. The volcanic and sedimentary rocks are regionally metamorphosed to pyroxene hornfels grade. The massive sulfides occur within a large (kilometer-scale) Na-depleted sericitic alteration zone. The immediate footwall and hanging-wall rocks to the deposit are characterized by zones of muscovite- biotite-sillimanite, lesser chlorite-biotite-cordierite, and locally intense silicification and sodium metasomatism. All lithologies have been affected by younger Ca-metasomatism. As currently defined, the Izok deposit comprises a cluster of five complexly zoned composite lenses: the Northwest, North, Central West, Central East, and Inukshuk lenses. The first four lenses are amenable to open-pit mining, whereas the Inukshuk lens will require underground development. The total indicated mineral resource presently stands at 16.5 million tonnes with a grade of 2.2% Cu, 11.4% Zn, 1.1% Pb, and 60 g/t Ag. Inmet Mining Corporation is presently reviewing the economic feasibility of developing the property."

Jan 1, 2004

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964