Search Documents

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By Ronald L. Bruening

IBC has developed a cost effective MRT process for the selective extraction and recovery of gold, copper, and a mixture of other base metals from mine leach cyanide solutions. This is a two-stage system in which the gold is first recovered selectively as a high purity salt. The copper is then recovered separately as a sulfate salt. The other base metals are then collected as a cyano anion concentrate. Three different SuperLig® materials are used. The first stage can be used alone on gold leach solutions where copper and other base metals are not a problem. The two or three stage system is used when the base metals build up in the leach solution, resulting in increased costs. The cyanide or cyanide/cyano anion concentrate can be recycled back to the leach solution until the build-up of other salts, etc. becomes too high, or this too can be controlled with a percentage bleed stream.

Oct 1, 2003

By E. M. Watkin

"Land directly disturbed by hard rock mining activities in Ontario and Quebec was surveyed in 1974 as part of a country-wide assessment, (Murray 1977). Some 15, 000 hectares, or 5 7 square miles, are listed as having been disturbed by overburden removal, waste rock and tailings deposition (Table 1) in the region. That area represents sixty-eight per cent of the total area which ha1; been disturbed by mining in central and Atlantic Canada. Assessment of disturbed areas was undertaken using LANDSAT-1 and LANDSAT-2 satellite imagery. Certain limitations of the technique were recognized but the data obtained were considered a relatively acceptable assessment of the extent of disturbed areas larger than ten hectares.Approximately ten per cent of the land disturbed by mining in the two provinces has been reclaimed to varying degrees. Indeed, this proportion is correct for the country as a whole. As pointed out by Ripley, Redmann and Maxwell (1978), some of the land was disturbed long before environmental concern 01· reclamation were ever considered. In numerous instances reclamation will remain impossible until presently active operations are closed. Nevertheless, these authors feel such figures make it clear that reclamation has not been a high priority in Canada in the past. Canada is a vast country, and there has been little pressure toward efficient use of all land space. Most mining operations occur in areas distant from the country's population centres. Under these circumstances, therefore, the pressure to reduce the environmental impact of mining is much less than in the more densely populated areas of Europe and the eastern United States, where such activity can occur in or adjacent to large metropolitan areas."

Jan 1, 1980

By J. A. Meech, R. J. Tucker

"A dynamic computer model has been developed to simulate the operation of ore crushing plants. The model was created in a general form to allow imitation of a wide variety of secondary crushing circuits with only minor program modifications. The system can be run on either a microcomputer or a large time-sharing main frame computer as required.The size reduction and separation characteristics of crushers and screens are based on standard manufacturers' design and performance data. These calculations are isolated within various subroutines to facilitate tailoring of the model to emulate any particular plant of interest. Input and output data are presented in a variety of formats. Crusher, screen and conveyor amperages and surge bin levels can be presented in a tabular form along with appropriate alarms arising from improper circuit operation or process interruptions. Graphical representation of the circuit together with strip chart data output are features of the system when operated in a microcomputer environment.The program is currently being used at Queen's University as a teaching aid to demonstrate plant operating characteristics, control strategies and design concepts. The acceptance of, and reaction to the program at this level indicates a good potential for it to provide a valuable tool for operator training."

Jan 1, 1985

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By N. A. Duke, R. L. Carpenter

Abstract - The West Meliadine area is underlain by structurally interleaved panels of mafic and minor ultramafic metavolcanic rocks and metasedimentary rocks that occur along the northern margin of the Neoarchean Rankin Inlet greenstone belt. Three structural and metamorphic domains are recognized: (1) the easterly Wesmeg domain; (2) the central Barracuda-Ridge domain; and (3) the westerly Peter Lake domain. The Wesmeg domain is characterized by a series of southeast-trending, north-dipping, foliation-parallel panels of greenschist facies mafic metavolcanic and metasedimentary rocks. The Barracuda-Ridge domain is comprised of greenschist to amphibolite facies mafic metavolcanic rocks that define an east-northeast-trending structural grain. The Peter Lake domain consists of amphibolite facies mafic metavolcanic rocks and minor metasedimentary rocks intruded by a monzonite pluton. West Meliadine hosts the economically significant Wesmeg gold deposits, as well as other important gold showings across the Barracuda-Ridge and Peter Lake domains. The geological setting of the Wesmeg gold deposits resembles that of a break or fault zone. The Pyke Break is a major geophysical discontinuity (>65-km strike length) and is the first-order structural control on gold mineralization at West Meliadine. It is several kilometers wide and characterized by polyphase deformation and shear zone development accompanied by lode-gold mineralization. In general, gold concentration is related to quartz and iron-carbonate veining, iron sulfides (mainly arsenopyrite and pyrrhotite), and accompanying silicate alteration minerals that overprint favorable chemical and structural traps late in the history of deformation.

Jan 1, 2004

By M. J. Fairweather

"The development of means to maximize the selectivity between galena and sphalerite in lead zinc ores is extremely important to the lead-zinc industry. Two challenging studies recently undertaken by Cominco will be reviewed. The first required an unusually fine grind to achieve liberation between galena and sphalerite. The second contained partially altered galena which resulted in unusual early activation of sphalerite under normal flotation conditions. Means by which lead and zinc separation were optimized in these two ores will be discussed.There are two important factors in the separation of minerals by froth flotation: particle size distribution (grind) and pulp chemistry. Pulp chemistry includes a number of factors including pH, Eh, collector type and concentration, inorganic depressants, organic depressants and activators.Grind is important for two reasons. A sufficiently fine grind is required to optimize liberation. However, if the mineral dissemination is too fine, mineral selectivity in the flotation process is impaired. Due to the hydrodynamic constraints of conventional mechanical flotation cells, flotation works best over the single decade size range between 10 and 100 microns. The majority of new ores treated by Cominco until relatively recently were comparatively simple. The major factor in their treatment was defining optimum grind size. Accordingly, the focus within mineral processing at Cominco was on grind and supporting liberation studies. The relationships between grind, liberation and flotation response are intuitively easy to understand. An idealized relationship is shown in the first figure."

Jan 1, 1991

This paper aims to increase our understanding about existing capacity-building approaches and their implications for obtaining a social license to operate in the mining industry. The notion of ?capacity building? is gaining increasing currency in the mining sector in developing countries due to a rapid rise in the globalisation of mining operations. Capacity-building is conceived here as a process that lasts after the mine-cycle, intended to provide local mining communities with tangible skills and knowledge to gain meaningful employment in mining or other industries relevant for the local economy. Building community capacity to understand and effectively respond to these transformations is vital for obtaining a social license to operate, as it promotes sustainable and locally relevant development. Accountability mechanisms such as global norms and international standards increasingly highlight the need to build capacity among stakeholders, particularly among local communities adjacent to mining operations. International frameworks and mining companies have embraced the notion of capacity-building as a driver to assist corporate social and operational performance. However, this narrow understanding of capacity-building through the prism of corporate social responsibility and ?best practice? is preventing the industry from meaningfully impacting communities and maintaining a social license to operate. This latter notion is being widely embedded across multiple industry sectors, as a social and economic reward from mining companies to compensate communities for natural resource extraction and gain social acceptance. Although both concepts are widely recognised in the minerals industry, insufficient attention has been paid to the implications of applying a top-down (mining-orientated) or a bottom-up (community-orientated) capacity-building approach for obtaining a social license to operate, or indeed how these two concepts are linked and applied in practice. At times, communities lack the necessary capacities in the form of education and skills to deal with mining-led livelihood transformations. This is preventing both mining companies and communities from forging sustainable livelihoods and responding to mining-led livelihood transformations, a situation that is creating discontent among communities and reducing the possibility of obtaining and renewing a social license to operate for the industry. Based on a review of current scholarly debates, accountability mechanisms in the mining industry and fieldwork findings in Colombia, this paper will contribute to an understanding of the implications of existing capacity-building approaches that support a social license to operate.

Aug 1, 2013

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By Claude Deveau

"Studies on the performance of Falcon batch type concentrators treating ultrafine tantalum at Tanco have revealed that very fine heavy minerals are concentrated within certain areas of the concentrate bed. This information led to the design of a bowl which would allow entrapped lighter low grade particles to escape while providing more space for heavier particles to be recovered in the bed.Numerous tests were then completed with a modified batch-type and non-fluidized Falcon bowl in which the diameter of the discharge lip was adjusted downward manually in steps. This allowed for the gradual building of a higher grade concentrate bed.This work ultimately led to the design of a new Falcon with an automated continuously variable lip. In April 2005, Tanco commissioned the first Falcon UF600.This paper will discuss laboratory scale results and also plant performance of the Falcon’s UF technology.INTRODUCTIONTantalum Mining Corporation of Canada, also known as Tanco, is a wholly owned subsidiary of Cabot Corporation based in Boston, Mass. Operating since 1969, the underground highly mechanized room and pillar operation produces tantalum, lithium and cesium minerals and is located a 2 hour drive east-northeast of Winnipeg Manitoba, Canada.At Tanco, tantalum is recovered using conventional gravity concentration, enhanced gravity concentration and flotation. This paper will discuss how the need for improved equipment to treat very fine tantalum particles was filled by a machine which was modified to the point of creating a completely new technology.In November 2003, Tanco began the investigation for the potential use of a high g-force smooth walled concentrator for treating ultra fine tantalum produced by its flotation circuit. Until then, the tantalum flotation concentrate had been treated by a circuit which consisted of a Mozley Multi-Gravity Separator 902 (MGS), a Mozley MGS 900 and a Bartles cross belt concentrator. Through QemScan analysis, it was found that the majority of the losses from this circuit were of an extremely fine nature which exceeded the recovery limits of equipment on hand. Mean particle size of the tantalum losses was less than 10 µm."

Jan 1, 2006

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By P. J. Deveaux, M. J. Kreczmer

The Tartan Lake deposit 12 km northeast of Flin Flon, Manitoba, was discovered in March of 1984 during the investigation of a VLF anomaly. The discovery hole intersected 16.83 metres averaging 21 gm Au/tonne. Since then, 99 holes, over 21,000 metres, have been drilled outlining 419,491 tonnes grading 11.79 gm Au/tonne in a di stinct group of mineralized lenses referred to as the Main Zone. Three other mineralized zones are known on the property but no reserves have been allowed for these, the South , East and Base Line zones. The Main Zone consists of seven parallel, east-west striking, quartz lenses. The lenses dip steeply to the north and plunge steeply west to northwest. Lens number l strikes for 160m and extends vertically to the 90m level. Within th is lens there is a 60m interval of low grade materi al. Lens number 2 is located about 5-l0m within the foo twall of Lens number I. Near surface this lens stri kes for 40m, at 200m level the strike length increases to 200 m. To date the deepest mineralization on Lens 2 has been intersected at a vert ical depth of 527m. Five smaller lenses are located in the foo twall of Lens 2 , containing gold va lues similar to the two main lenses but erratically distributed. The South Zone, located 100m south of the Main Zone, strikes east-west fo r l00m above the 100m level. The East Zone, found 230m east of the Main Zone, strikes fo r 80m and may possibly be an ex tension of the South Zone. The Base Line Zone is located 275m south of the Main Zone. Sporadic, but very significant gold intersections have been obta ined1n all three zones. Gold-bearing quartz-ca rbonate tourmaline veins are generally confined to a silicous crystal tu ff hori zon. The crystal tuff exhi bits fi ve distinct types of alteration: silicification, sericitization, ca rbonati zation, chlorit ization and pyritization. Silicification has resulted in a perasive addition of silica and the generation of multiple quartz veins. Sericiti zation is restricted to the crystal tuff. All rock units are pervasively carbonatized . Ankerite is abundant in the quartz veins and within the shear zones, particul arly those located along the chilled margin of a nearby gabbro-diorite intrusion. Chloritization is widely spread th roughout the rock units, while pyritization fo rms a broad alteration halo associated with the orebody. Sulphide accesso ry minerals associated with the gold , whi ch fo r the most part appears to be free, are chalcopyrite and pyrite. Generally, the higher grade gold values are related to an increased content of sulphides in the qua rtz veins. The average sulphide content in the deposit is less than 5 %.

Jan 1, 1986

By C. J. Hodgson

"IntroductionThe Kitsault molybdenum mine is located 600 m above sea level on Lime Creek at the head of the inlet of Alice Arm, 140 km northeast of Prince Rupert, British Columbia (Fig. 1). The area of the mine is characterized by rugged topography and deeply incised creeks which drain into the Portland Canal - Observatory Inlet fjord system. Access is by air service or boat from Prince Rupert, or by secondary road from Terrace.HistoryThe deposit was first staked in 1911, at which time the main feature of interest was a polymetallic vein with values in silver located southeast of the molybdenum deposit (Woodcock and Carter, 1976). Turnbull (1916) was the first to describe the extensive zone of crisscross quartz stringers with Mo~ on the banks of Lime Creek which, although it clearly had the potential to contain a major deposit, was not then believed to be of commercial value.Following sporadic work through the 1920s and early 1930s, the ground lay idle unti11959 when Kennco Explorations (Western) Ltd. commenced a program of systematic diamond drilling on the stockwork-type mineralization adjacent to Lime Creek. In late 1964, Kennco announced the presence of an orebody of 36 million tonnes averaging 0.230Jo Mo~ which was to be put into production at a rate of 5450 tonnes per day under a new subsidiary, British Columbia Molybdenum Ltd., at a forecasted capital cost of $20 million (revised to $30 million).Between January 1968 and April 1972, 10.4 million kg of molybdenum were produced from 9.3 million tonnes of ore, at an average mill recovery of 90%, and with an average mill head grade of 0.206% Mo~. The ore was mined in an open pit with a waste to ore stip ratio of 1.5 to 1. The. operation was terminated in 1972 due to weak molybdenum prices and escalating costs.In May 1973, the deposit was purchased by Climax Molybdenum Corporation of British Columbia, Limited and in 1979 transferred to affiliate Amax of Canada Limited. In early 1979, following completion of detailed feasibility studies, Arnax commenced construction of the 10 900 tonne per day Kitsault mine and mill complex based on a mineable open pit reserve of 95 million tonnes at an average grade of 0.192% Mo~, sufficient for a mine life of 25 years. The original capital cost estimate was $143 million; it subsequently escalated to approximately $200 million."

Jan 1, 1995

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By H. L. Cheng, C. H. B. Leitch, C. T. Hood, A. J. Sinclair

"Epithermal Zn-Pb-Cu-Ag-Au quartz-carbonate-barite veins at the Silver Queen mine near Owen Lake, west-central British Columbia, are hosted by Late Cretaceous Tip Top Hill andesitic volcanic rocks. The veins form a rectilinear northwest-northeast pattern that differs slightly from regional structural trends. The main northwest-trending veins are oriented very close to the trend of regional northwest faults, but the crossing veins tend to be more east-north-easterly (070 degrees)compared to a regional north-easterly trend (040 degrees). The character of the veins suggests they are extensional features formed by dextral slip related to Paleogene oblique subduction, or intrusion of magma at depth, or both.In detailed exploration at the mine, the veins cannot be modelled as simple tabular sheet-like bodies. Instead, they are complex structures that divide and rejoin, forming multiple veins or stringers, or are found in shear zones as replacement features with quartzsericite- clay-carbonate-pyrite alteration haloes of variable width that make definition of vein margins and correlation from hole to hole ambiguous. In addition, individual veins within each of the main structures have en echelon characterboth along strike and down dip.Geological and assay data must be carefully studied to define the margins of these complex veins before any estimation of ore reserves may be made. Where multiple veins occur in a section, ore/gangue mineralogy, assays, character of wallrock alteration, and thickness of vein and mineralized hangingwall, median and footwall zones must be used to evaluate continuity of mineralized structures. Well-defined sections are projected into areas of increasing complexity. Once the vein boundaries are defined, metal concentrations, important metal ratios(Au/Ag, Pb/Zn, Cu/Zn), and true thicknesses of the vein provide the basic data for reliable ore reserve estimation."

Jan 1, 1991

By J. F. McMahon

Introduction The greater portion of the information presented in this paper was obtained in the course of an investigation on clay gathering and its cost in the provinces of Quebec and Ontario (1). For assistance in the preparation of the paper, the writer wishes to record his thanks to Mr. Howells Fréchette, Chief of the Ceramics and Road Materials Division of the Mines Branch. Clays are mineral substances consisting essentially of hydrous aluminium silicate which become plastic when wet, fairly hard when dry, and stony masses when burned to a sufficiently high temperature and re-cooled. Shales are clays which have been indurated by the processes of nature. Millions of tons of clays and shales are won yearly for the production of brick, tile, sewer pipe, drain tile, roofing tile, fire-brick, china-ware, wall and floor tile, cement, and a host of other products. There are certain types of clay which, due to their particular qualities and limited distribution, are mined entirely or in part for sale to manufacturers, and are even exported from one country to another, as for example china-clays or kaolins, utilized in the manufacture of white-wares and in the paper industry, due to their consistent whiteness; ball-clays, utilized in the white-ware industry, due to their bonding power and whiteness; slip-clays, used in the stone-ware industry because of their glazing properties, and in the grinding-wheel industry for their burned bonding properties; and suspension-clays, such as are used in the enamelling industry. However, the great bulk of clays and shales won are used in the production of heavy clay products, and the manufacturer of these generally owns and operates his own deposit of raw material.

Jan 1, 1933

By Dogan Paktunc, Larry J. Hulbert, Robert C. Carne, D. Conrad Grégoire

Abstract -A thin layer of stratiform Ni-Zn-PGE sulfide mineralization of sedimentary-diagenetic origin was deposited during the Middle to Upper Devonian in the euxinic "Nick basin". The mineralized unit (2:3 cm thick), which seems to have been developed over the entire sedimentary basin of >80 km2, consists of pyrite, vaesite (NiSi), and sphalerite. The average grade of the mineralization is about 5.3% Ni, 0.73% Zn, ?770 ppb (PGE+Au), and up to 61 ppm Re. Anomalous Se, As, Mo, P, Ba and U are present. A minimum of 0.90 x 106 tonnes of Ni were deposited in the basin (based on a bed thickness of 3 cm) during the Devonian. The unique metal association, extensive lateral distribution, persistent metal grade, mineralogical makeup, and stratigraphic control demonstrate that this is a new deposit type and a new geological environment for Ni and PGE +Au. The sulfide layer occurs at the base of a Phosphatic Chert Member which is underlain by a distinctive marker unit consisting of concretionary limestone structures. The limestone spheroids may represent a vent-specific carbonate facies developed adjacent to faults that emanated nutrient­ rich hydrothermal discharges just prior to the main mineralizing event. The suite of elements associated with the Nick mineralization suggests that the ore-forming metals were originally bound to organic matter derived from decaying marine organisms. Discharge of hot brines bearing organic­ matter-bound metals took place along numerous conduits within basin faults that are now manifest as bitumen veins. Our syndiagenetic model proposes that these fluids were discharged laterally from the conduits into the unconsolidated bottom sediment (ooze). The introduction of this metalliferous fluid, rich in organic matter, stimulated biological activity and bacterial reduction of its contained S04 to sulfide. Hot, dense, laterally migrating hydrothermal fluid precipitated thin sulfide-rich 1arninae within bottom sediment. Published thermodynamic studies suggest that the diagnostic vaesite­ pyrite assemblage crystallized at approximately 138°C. The ?34:S values range from -14.7 o/oo to-10.0 o/oo and are up to 34 o/00 lighter than locally surrounding sulfides and age-equivalent mineralized strata elsewhere in the Selwyn Basin. The ?13:C values of calcite in the footwall of the mineralized unit ( -12 o/00 to -6 o/00) are isotopically much lighter than regional values. The lighter isotopic character is attributed to the hydrothermal discharge of fluids enriched in organic compounds. Although geochemical profiles of the lower Earn Group sediments that host the Nick mineralization reveal that these black shales are not distinctive, the unusual Ni, Zn, PGE, U, Ba, and P elemental associations and their anomalous concentrations in stream sediments can be used to explore for this deposit type.

Jan 1, 1992

By Arnold Blaisonneau, Théophile Guillon, Xavier Rachez, Sylvie Gentier

"L’étude présentée ici vise à étudier l’influence, lors de stimulation hydraulique de puits dans les réservoirs géothermiques de type Enhanced Geothermal System (EGS), du comportement mécanique des zones de failles recoupant le puits sur la réponse hydraulique du réseau de fractures 3D. Dans ce but, un modèle 3D, basé sur la méthode des éléments distincts et dans lequel les zones de failles recoupant le puits sont modélisées par des fractures numériques 2D, est mis en oeuvre. Les modélisations présentées ici visent à caractériser l’influence du comportement mécanique (type de comportement, hétérogénéité) sur la cinétique de la stimulation hydraulique, ainsi que sur son effet spatial autour du puits. INTRODUCTIONPour le développement de l’exploitation géothermique de type Enhanced Geothermal System (EGS), la phase de stimulation conditionne grandement le succés du projet ; en effet, elle a pour objectif d’augmenter l’injectivité et la productivité des puits et doit permettre d’assurer la connexion entre les puits d’injection et de production garantissant ainsi la viabilité technique et économique de l’échangeur. Pour le site EGS de Soultz-sous-Forêts (France), parmi différentes techniques de stimulation, la stimulation hydraulique a été utilisée à cette fin en provoquant une augmentation irréversible de la perméabilité autour des puits. Dans ce type de réservoirs fracturés, le but des stimulations hydrauliques est de réactiver, plus spécifiquement en cisaillement, des structures hydrauliques pré-existantes (fractures, zones de failles etc.) dans le socle cristallin. La compréhension des phénomènes physiques durant la stimulation hydraulique est cruciale pour optimiser cette technologie et pour contrôler/limiter les risques associés (viabilité technique et économique des puits, sismicité induite etc.). C’est notamment le cas pour la relation entre le comportement mécanique des structures stimulées et les conséquences sur le comportement hydraulique dans un contexte tectonique spécifique."

Jan 1, 2015

By Sylvie Brassard

Available information ?? InfoMine: mineral properties ?? Metals Economics Group: budgeted exploration expenses ?? MineScan: Canadian and American Mining Companies ?? Statistics Canada: Canadian Direct Investment Abroad, by Sector in the world OR all sectors by Country

May 1, 2008