Search Documents

By Pingyang Zhang, Caichu Xia, Shuwei Zhou, Yu Zhou, Yongsheng Hu

A lined rock cavern (LRC) is an alternative container for compressed air energy storage (CAES) to store high-pressure air that is later used to produce electricity. A critical requirement of CAES in LRCs is that the inner seal should provide adequate sealing capacity to prevent air leakage from LRCs. In many studies, rubber sheets are applied to build the inner seal. However, air leakage through rubber seals has not been given much attention and rubber seals are usually assumed to be absolutely airtight. Given that rubber is permeable especially under high air pressure, such as in CAES, air therefore leaks through rubber seals during CAES operations. In this study, a numerical analysis was conducted based on the permeation equation of polymers and the governing equations of thermodynamics of CAES caverns to analyze the characteristics of air leakage from CAES caverns through rubber seals. A planned CAES plant in China was considered as a case study. Results show that air leakage rate increases with increasing cavern temperature and pressure during air injection and decreases as cavern temperature and pressure decline during air withdrawal. However, in total, the daily air leakage percentage is in the order of magnitude of 10-3% in a typical operation cycle, which is much smaller than the critical value of 1%. Under a common range of realistic operations conditions, the daily air leakage percentage is still of the order of 10-3%. Therefore, rubber seals can be used to prevent air leakage in LRCs for CAES. However, the experience of Japanese pilot cavern indicates that the specifications for the on-site vulcanization jointing and installation methods of rubber seals still need improvement.

Jan 1, 2015

By E. Godfrey

The average man one meets on the street thinks of an explosive as a medium of death and destruction, something unstable which should be given a wide berth, because he knows little or nothing about its use or its stability. Briefly, explosives are compounds that develop very large quantities of heat and gas in an extremely short time and in a small space, thereby exerting enormous pressure upon surrounding bodies, and by the rapid expansion of this highly heated gas are able to perform a considerable amount of useful work. The amount of heat generated and the volume of gas produced by the decomposition of an explosive determines the amount of mechanical work it can do, and the time occupied by its change from solid or liquid condition to gaseous condition determines its shattering effect. Explosives manufactured by reputable people are not extremely dangerous, on the other hand they are quite safe if handled in a proper manner. Furthermore, before an explosive can be placed on the Canadian market a sample must be submitted to the Explosives Division of the Mines Department, who may condemn or permit its manufacture, according to their findings regarding its safety in handling and its stability during storage.

Jan 1, 1926

By D. R. Boyle

"The basal type uranium deposits in south central British Columbia occur within unconsolidated, late Miocene fluvial paleochannel sediments that overlie major fault zones within the Okanagan Highlands Intrusive Complex. Prior to the formation of mineralization, paleovalleys containing host sediments were flooded by Pliocene valley basalts of the Plateau Basalt Formation. Five uranium deposits have been outlined to date, of which the Blizzard (4020 tonnes U) and TYee (650 tonnes U) are the largest. The basement intrusive complex underlying the deposits varies in age from early Cretaceous to Eocene and is comprised of quartz monzonite, granodiorite, Coryell monzonite, porphyritic granite and pegmatite.The mineralized host sediments comprise a complex sequence of interfingering conglomerates, arkosic sandstones and mudstones. Organic material is abundant in many, but not all, mineralized beds. Uranium mineralization is present in the form of uranous (ningyoite) or uranyl (saleeite, autunite) phosphates coating clastic grains and filling voids. Because of very strong reducing conditions related to large concentrations of marcasite and organic material, ningyoite is the only uranium mineral in the Tyee deposit, whereas the Blizzard deposit contains a more complex assemblage of minerals (saleeite, autunite, ningyoite). The observed paragenetic sequence of mineral precipitation in the Blizzard deposit (autunite-saleeite-ningyoite) indicates that the uranyl minerals, saleeite and autunite, are primary. Small amounts of Zn, Ni, Co and Mo have been introduced into the Blizzard deposit whereas Mo is the only non ore-forming element enriched in the Tyee deposit. Mn is the only depleted element in both deposits."

Jan 1, 1986

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or 'breaks' as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By P. G. Claridge, G. P. Holmes, M. A. Redfearn

"IntroductionThe purpose of this chapter is to describe current practices in operation and maintenance of flotation circuits in Canadian mineral processing plants. The chapter consists of five sections covering description of equipment, typical flow diagrams, operating practice, instrumentation and maintenance. The approach to this subject matter is intended to be practical in nature, hence no deeply technical treatment of flotation theory will be included.Flotation is an extremely common method of beneficiation of ores. Reasons are the relatively low cost of flotation compared to many other processes, the wide range of minerals to which flotation may be applied and the high efficiency of separation which can usually be achieved. The flotation process as we know it today has been developed within this century and it has had a major impact on the mining industry. While flotation is commonly considered to be important because it provides a relatively simple method of separating minerals in complex ores, the availability of flotation has also made a multitude of mineral deposits in Canada into economically viable mining operations because it allowed production of a concentrate of valuable minerals from the ore. These concentrates could then be transported from geographically remote locations to centraHzed plants for further processing, although the existence of the remote and perhaps small ore body alone would not have justified installation of metallurgical processing plants on site and the grade of ore would not have justified direct shipment of ore.Some of the more common minerals concentrated by flotation are sulphides of copper, nickel, cobalt, iron, zinc, molybdenum, lead and arsenic, as well as non-sulphides such as sodium chloride, potassium chloride, phosphates, silicates, chromite, fluorite, limestone and coal. Precious metals are also recovered by flotation, generally in association with another sulphide mineral."

Jan 1, 1989

By M. A. Nagle

Various strategic projects were carried out in 2002 to increase the capacity of Teck Cominco's integrated zinc-lead smelter at the Trail operations site in British Columbia, Canada. The lead smelter treats the iron residue from the zinc plant and optimizes the overall zinc recovery. This paper summarizes two options that were considered to reduce the zinc content in the leaching iron residue. The first option involved increasing the capacity of an existing hot acid leach circuit up to the iron loading constraints of the circuit. The second sought to maximize the hot acid leach capability by separating the ferrite-rich solids, followed by aggressive hot acid leaching (>100°C) and subsequent iron precipitation. Different forms of iron precipitation were reviewed in order to determine the most effective and economical approach. Among these, was a novel high temperature ferrite conversion process. The technical results and selection criteria are presented together with possible ways to integrate the process concepts into the current sulphide leaching plant circuit. The first option was selected for implementation and is currently being operated successfully.

Jan 1, 2006

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By Jas. G. Ross

Introduction Asbestos, a mineral known and used in ancient times, has become an article of commerce only during the life of the older asbestos miners in Quebec. The diversified uses of this adaptable substance are now numbered by the hundreds. Wherever insulation or resistance to heat may be required, asbestos, either by itself or mixed with some other material, may be employed to advantage. Regarded as a curiosity for centuries, it is now in such common use that it is familiar to all. The demand for long fibre for use in the manufacture of textiles and brake-lining, and for shorter fibre for making shingles, paper, and insulation materials, serves to support the industry of mining asbestos-bearing rock and milling the fibre from it in Canada, South Africa, Russia, Cyprus, and the United States. The commercial use of asbestos dates only from 1876, in which year large deposits were discovered in the Province of Quebec, Canada. Prior to that year a small amount of long fibre amphibole asbestos was produced in Italy. Occurrence In Canada In the Eastern Townships of Quebec, along the line of the Quebec Central railway, is an area of serpentine rock. It extends westerly into Vermont and easterly to Gaspe. A part of it, the section from Danville to East Broughton, contains areas in which occur deposits of commercial asbestos fibre of the chrysotile variety. Pits have been opened on some of these deposits at Danville, Coleraine, Black Lake, Thetford Mines, Robertson, and East Broughton. Thetford is distant 68 miles from Quebec city, East Broughton lies 25 miles to the northeast of Thetford, while Danville is 45 miles to the southwest of Thetford.

Jan 1, 1927

By E. M. Stiles

THE Wellington Lake power plant of the Consolidated Mining and Smelting Company of Canada, Limited, about 25 miles from Goldfields, Saskatchewan, is the second hydro-electric project operating in that Province, the first being the Island Falls plant of the Churchill River Power Company which serves the operations of the Hudson Bay Mining and Smelting Company at Flin Flon, Manitoba. The Churchill River project develops 90,000 h.p. at 56-ft. head; the Wellington Lake plant 3,300 h.p. at 75-ft. with pro-vision for an additional 3,300 h.p. unit. Churchill River power is trans-mitted at 110,000 volts over a 58-mile line of steel towers to Flin Flon and an additional 45 miles over a wooden pole-line to Sherritt-Gordon. Our steel tower-line is 22 miles long, and the voltage is 60,000; this choice be-cause certain such equipment was available from Trail. The diversion of 15,000? second-feet at 56-ft. head for 90,000 h. p. at Churchill river dwarfs our 500 second-feet flow at 75-ft. head for 3,300 h.p. In both cases, the main obstacles to be overcome during plant construction were the lack of transport facilities and the short open season. Let it be noted here that this paper deals mainly with those phases of plant construction which were particularly interesting to the writer. With-out these variations from the ordinary routine, this is just another power project whose story is better told by the accompanying charts and pictures. To many members of the Institute it is still just that; but I am writing for those who, like myself, have been too seldom responsible for major under-rakings at an appreciable distance from a railway siding. When it was planned in early 1937 to erect a 1,000-ton mill at our Box mine, both hydro and Diesel power were discussed. With ten years' ore in sight, even an expensive hydro project, such as ours turned out to be, produces kilowatts materially below the 2-cent operating cost of a Diesel plant using fuel-oil at 14 cents a gallon.

Jan 1, 1940

By Lan Vu

"The Ferderber mine consists of a series of Archean gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz diorite Bourlamaque batholith. This zone has sharp contacts with the enclosing quartz diorite, and on average strikes N70E and dips 65SE. Along the contact with the shear zone, the quartz diorite is chloritized, sericitized and carbonatized. The chlorite schist within the zone is probably derived from mafic dykes.The geometry and distribution of structural features within the Ferderber shear zone suggest a long history of repeated movements. The majority of gold-bearing lenses were first emplaced during a probable early period of brittle shear which resulted from strike-slip movement. They were then folded and pulled into boudins by a later episode of reverse movement that accompanied ductile shear. New mineralized veins were emplaced in the shear zone and deformed at this time.Mineralized veins are dominated by quartz, carbonates, tourmaline and micas. Gold is more common within pyrite where chalcopyrite is abundant and is generally in contact with both pyrite and chalcopyrite at ""triple point"" grain junctions. This intimate association suggests that copper may have played an important role in gold deposition.Recent exploration has shown that the Bourlamaque batholith is cut by many parallel or en echelon shear zones. Study of ""Landsat"" and aerial photographs has indicated a number of linear structures striking ENE-WSW and ESE-WNW which form a conjugate system. The intersection of these two structural trends presents an interesting exploration target."

Jan 1, 1990

By W. S. Tremaine

When the Hedley Mascot mill was built in 1935, it was designed as a straight flotation plant. The ore to be treated at that time was a gold ore in which the gold was intimately associated with arsenopyrite and pyrrhotite in highly silicified and garnetized limestone gangue. This material was ground to 85 per cent minus 325 mesh in two-stage grinding and floated in standard flotation cells to produce about a 5-ounce concentrate, which was shipped to Tacoma smelter for refining. This arrangement gave us a recovery of about 89 per cent. Test work indicated that the best way to improve this recovery would be to build a cyanide plant to treat our flotation middling. Arrangements for the construction of this plant were finally approved and work on it was started in the spring of 1940. This plant was of the conventional type in which the flotation middlings were thickened, filtered, and then put through the usual cyanide process. Its capacity was 50 tons of middlings per day. This arrangement worked quite satisfactorily and gave us an increase in overall recovery of 4 per cent. Unfortunately, about the time the plant was completed, we developed, and started to ship to the mill, ore that differed entirely from that met with up to that time. Instead of being hard, it was very soft, the orebody from which- it came being much faulted and brecciated. In many sections, the sulphides were oxidized and the breccia was filled in with a very soft, hydrous iron silicate known as chloropal. When this new ore was mixed with the old ore and sent to the mill, the whole operation was disrupted. The chloropal slimed so badly that the classification, flotation circuits, and cyanide plant would not handle it. The difficulty in the cyanide plant was at the head end, where the 10 ft. by 20 ft. thickener and the 8 ft. by 8ft. drum filter would not handle the middlings containing a large percentage of primary slime and chloropal. This material would not thicken to more than 30 per cent solids in the thickener and, when pumped to the filter, would forma very thin, slimy cake. Overall recovery dropped to between 83 and 84 percent and it was quite apparent that some extensive changes would have to be made in our flow-sheet before this ore could be treated successfully.

Jan 1, 1947

By H. Thomasson

THE war, like all destructive agencies, has focused attention on salvage and conservation, and to such an extent that a decade of normal progress has been crowded into a few months. This is particularly true as regards the repair of cutting tools. As a consequence, there has arisen a wide demand for comparable data by those engaged in such work, and for basic information by others who wish to repair tools. These repairs may be grouped in three classes: (1) The repair of broken tools of relatively slender cross-section, such as broaches, reamers, drills, etc., of a type that could be returned to service if a means to join the broken surfaces were available, as fortunately it is in the low-temperature silver solder process; (2) the repair of tools that possess shanks, tangs, and other non-cutting portions that may be broken or damaged to the extent that only the addition of metal will permit their return to service; and (3) the repair of special rotating tools, such as end-mills and milling cutters, that may have portions broken from the cutting edges or have their edges so worn in service as to require building up.

Jan 1, 1943

By Kyeong Woo Chung, Ho-Sung Yoon, Jyothi Rajesh Kumar, Chul-Joo Kim, Sung-Don Kim

The aim of the present study is to investigate the extraction, separation and recovery of the indivisible metals of dysprosium and neodymium from permanent magnets scrap leach liquor solutions with meaningful recovery. The present experimental development focused on dysprosium separation from neodymium and recovery by suitable mineral acids. Fundamental studies of the effect of time, pH and extractant concentration on the metal separation were conducted followed by proposal of a mechanism for extraction. Process development included generation of McCabe-Thiele diagrams and counter current extraction (CCE) studies. After loaded organic generation from the CCE process, this was followed by scrubbing studies as well final recovery of dysprosium.

Jan 1, 2014

By A. J. MacEachen

"LIKE ALL OTHER NOVA SCOTIANS, I have been thrilled during the past few years with the growing evidence that substantial reserves of oil and gas are being discovered off the Atlantic coast of Canada. There are those in this province who believe that large-scale commercial production is just around the corner, and that when it starts Nova Scotia will begin to float on a sea of royalties. These overly optimistic people, of whom I am not one, are convinced that with the first barrel of oil shipped to market, Nova Scotia can forget its financial problems while its people take on the luxurious lifestyle of the shieks of Kuwait or Saudi Arabia. You and I know, however, that even though offshore oil and gas may turn out to be the greatest gift nature has ever bestowed on Eastern Canada, it may take some considerable time before the reserves can be accurately assessed, before the industry can become fully operational, and before the benefits of production can be translated into royalties and tax revenue, improved public services, new industrial facilities and more jobs. While it is premature for the ordinary Nova Scotian to take on the habit of buying expensive cigars and lighting them with ten-dollar bills, it is not too early for him to insist that governments and industry plan intensively and well for the beneficial exploitation of undersea resources."

Jan 1, 1973

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By T. C. Crosby

"Grinding has a marked effect on concentrator recovery and operating cost, and improved operation through automatic control can enhance plant performance. The correct application of automatic control can only be accomplished after the basic process variables and their effect on mill operation have been defined. This paper develops a control system for a closed circuit grinding system. Typical control systems, such as those for feed, water flow, level and circulating load, are discussed. A method of determining controllability, using the calculated reaction curve technique, is outlined. Various successful automatic grinding control applications are discussed and future possibilities are outlined. Although this paper primarily deals with closed wet grinding• circuits, the principles involved can be readily applied to other processes."

Jan 1, 1967