Search Documents

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

By G. Vibert Douglas

It often happens that the field geologist encounters a fault in ground where there is little to guide him with regard to the throw, or vertical displacement, and the heave, or horizontal displacement. The following construction gives both of these components of the fault, and the writers hope that it may prove a help to others. The construction is applicable to both normal and reversed faults. Briefly the procedure is as follows: Take a point which is common to the faulted geological feature and to the fault plane and on the downthrow side of the fault. Move this point in the horizontal plane in the direction indicated by the fault striæ. Rebat the point down to the plane of the fault and obtain its throw. Next consider the other side of the fault and truncate it down by the amount of the throw just determined. Then project the line of the geological feature through to the trace of the fault-plane at the lower horizon. The result is the relative positions of the two parts of the original geological feature as severed by the fault. In Figure r, let us consider a typical normal fault, that is, a fault in which the hanging-wall has gone down relative to the footwall. This characteristic, or its alternative, the reversed fault, is determined by observation on the ground. Let AB be the line of any geological feature such as the edge of a dyke, vein, or bedded sediment. The plane of which AB is the trace may have any dip; in the present case let us say 70° right. Let FF be the trace of a fault-plane which may have any dip; let us say 35° left in this case.

Jan 1, 1928

By R. R. Tatiya

"The ultimate aim of a mine design is to determine the development work involved and resources required by adopting one or more specific alternatives. A part of the process is the production of mining plans/designs, an outline of the amount of work and costs involved as well as a prediction of the revenues expected. The paper aims to examine these aspects of mine design using the computer models developed. These models are capable of designing and performing economic analysis for one or more stopes for a continuous orebody. IntroductionTatiya and Allen (1987) have described ’defining stope boundaries using a computer.’ Using the stope boundaries defined or even hypothetical ones, algorithms have been prepared to design the layouts of the following stoping methods: 1. sublevel stoping (longitudinal as well as transverse);2. DTH (Down-the-hole) stoping; and3. flat back cut and fill stoping with posts and pillars.Tatiya (1989) presented this work at the 21st symposium on the application of computers and operations research in the mineral industry (APCOM). Economic analysis of a stope is the additional feature incorporated with these algorithms.The system has been tested by an economic analysis of the three stoping methods modeled for a small portion of a deposit of a copper mining complex. The deposits at this mining complex form lenses of varying shapes and sizes, having low copper content. These chalcopyrite lenses are steeply inclined with a thickness in the range of 5 m to 60 m. The strata are competent and suitable for underground mining.In different sections of the mines different sets of equipment are used to perform the basic unit operations. Some of the ore handling levels in the mines are trackless, the rest are tracked."

Jan 1, 1998

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By B. Farabi Khoshmehr

In the present study the effect of Silicate Sodium oxidation agent concentration and Plasma Electrolytic Oxidation (PEO) treatment time were investigated on properties of oxide layer on Aluminum alloy. The phase composition and surface morphology of PEO films were evaluated through x-ray diffraction (XRD) and scanning electron microscopy (SEM). Pin on Plate abrasive machine were used to investigate of were resistance of coating. The results showed that oxide layer which formed on Aluminum surface consist of high temperature a- Al?O? and ?- Al?O? phases. The diffraction peak intensity and percentage of these phases were increased by increasing silicate sodium concentration. Microscopic studies revealed a porous surface for PEO coating. This was affected by silicate sodium concentration and oxidation time. The wear test results showed that the weight loss of PEO coating was reduced due to improvement of their wear resistance.

Oct 1, 2011

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By Philippe Henry

HYDROMETAL is using suitable technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy while keeping the environment cleaner. Hydrometal is treating on average 60000 t per year of complex materials through a unique hydrometallurgical recycling concept. Zn, Cu, Sn, and Pb are the most important in volume, but in the last 15 years, Hydrometal has also developed a few specific recycling treatments for the minor metals including Ge, In, Co, etc. In 2010, Hydrometal commenced the recycling of RE (Rare Earths) from wastes generated by the RE refining industry in Europe and has decided to initiate new recycling projects for the RE recovery from the magnet or glass industries. Two case studies of recycling of materials in our integrated hydrometallurgical facility (Hydrométal) in Belgium are discussed: recycling of cerium from polishing sludges; and recycling of Ni- Co from cement produced in the zinc industry.

Jan 1, 2014

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By C. Gaubert, G. Bourassa

"The construction or rebuild process in the anode baking furnaces has been modeled with the software Rockwell Arena, in order to minimize the process cost and risk. The case study was focused on the sectional rebuild (""on the fly"") that needs a high coordination of the material inventory, the on-site personnel and the construction/production schedule. Multiple entities and resources were allocated for the different part of the process (in-furnace process, prefabrication, materials transportation, etc.). Logic flow charts and VBA macros were used to simulate the space utilization (including cranes utilization) and interaction with production. MS-Excel output files can show user-friendly results."

Jan 1, 2006

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By C. I. Godwin

"The relative-value (R-value), discrimination-factor (D-factor), and vector-ratio (V-ratio) method (RDVM) provides a geological knowledge-based statistical and geological-genetic interpretation scheme for geochemical data that enhances discovery in geochemical exploration. The practical advantage of RDVM is that it synthesizes geochemical features geologically related to ore-deposit discovery in three steps: reclassifying element concentrations using log-probability plots into R-values; calculating geologically defined D-factors from R-values; and determining V-ratios. D-factors are the sum of R-values, divided by the number of R-values summed. Based on the analyses selected, D-factors mimic rock or mineral deposit signatures. V-ratios refine interpretations of rock type and vector to orebody locations.RÉSUMÉ La méthode de la valeur relative (valeur R), du facteur de discrimination (facteur D) et du rapport de vecteurs (rapport V) (RDVM), fournit un schéma d’interprétation des données géochimiques basé sur les statistiques et les connaissances géologiques et la génétique géologique; ce schéma contribue aux découvertes en exploration géochimique. L’avantage pratique de la RDVM est qu’elle fait la synthèse des caractéristiques géochimiques reliées géologiquement à des découvertes de gisements de minerais en trois étapes : une reclassification des concentrations des éléments au moyen de courbes de probabilité logarithmique en valeurs R; un calcul des facteurs D définis géologiquement à partir des valeurs R et la détermination des rapports V. Les facteurs D sont la somme des valeurs R divisés par le nombre de valeurs R additionnées. Selon les analyses choisies, les facteurs D imitent les signatures de la roche ou des gisements minéraux. Les rapports V peaufinent les interprétations des types de roches et dirigent vers des emplacements de gisements."

Jan 1, 2016

By M. L. Jeremic

Altered and unaltered coal from the Star-Key Mine near Edmonton, Alberta has been tested under compression and under tension. The test results showed that altered coal samples have an appreciably lower strength than unaltered coal. Altered coal samples do not give a linear load-displacement curve, peak strengths are poorly defined and yielding is observed over a range of loads, so the material can be regarded as relatively plastic. However, unaltered coal samples produce a linear loading curve with a high tangential modulus and an easily distinguished peak strength at which there is a sudden brittle failure. These findings lead to important differences in the theoretical design of ribs and pillars in underground mines in the two coal types. The substantial differences in the strength properties and behaviour of the two types of coal are governed by a higher intensity of cracks in the weathered coal. Two causes of the additional cracking can be suggested-subaerial weathering and subterranean weathering of the coal.

Jan 1, 1979

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By Mike Fontaine

The success of a project is defined by meeting the financial performance objectives of the business case within a stipulated timeframe. Early in design, little information is normally available; the uncertainty introduces risk to the project outcome. Using a range of risk management tools and techniques, a project can be developed from front end loading phases 1 through 3 (FEL1–FEL3), and project implementation (FEL4) and then into operations with an optimized probability of success. For every project element, the risk management framework embodies: establishing a context; assessing risk (identify, analyze, and evaluate); and treating risk. Embedded within design activities, this process mitigates or eliminates risks. Monitoring and control, as well as extensive communication and consultation with stakeholders, is integral to the risk management process.

Jan 1, 2015

By H. Westengen

The AE alloy family exhibits remarkable combinations of properties when utilized as high pressure die castings. This performance relies on the fact that the rapid cooling rate resulting from the direct contact between the molten alloy and the steel die walls effectively refines the structure through rapid solidification. Furthermore, the rare earth additions modify the solidification pattern, dramatically reducing the solidification interval. A solid shell forms at temperatures exceeding 500C, reducing the tendency for die sticking and inverse segregation. As a result, the die castability is excellent, giving parts with a smooth and shiny surface. Unlike other magnesium die casting alloys developed to improve elevated temperature creep properties, AE alloys do not suffer from the commonly observed tendency to introduce brittleness. This feature is attributed to the fact that the massive magnesium- aluminium intermetallic phase is substituted by a finely dispersed lamellar structure of Al-RE intermetallics. The resulting combination of excellent elevated temperature properties and good ductility, as well as excellent corrosion resistance, means superiority of these alloys for demanding automotive engine and chassis applications.

Jan 1, 2006

By J. L. Jambor, M. J. Baker, M. J. Logsdon

"Abstract - Prior to the development of the Diavik Diamonds Project, baseline studies were conducted to determine the geochemical characteristics of four kimberlite orebodies as an aid in the design of both the water-management system and the facilities for containment of processed kimberlite and ore stockpiles. Materials tested included field samples of volcaniclastic and pyroclastic kimberlite, processed kimberlite (i.e., kimberlite ore which had been screened and washed as part of the processing procedure), and sedimentary mudstone (a minor xenolithic unit which was assimilated during kimberlite emplacement). Approximately 200 samples of kimberlite materials were collected as part of the geochemistry program. Test-work included whole-rock chemical analyses, acidbase accounting, kinetic leach tests using columns, and mineralogical analyses. Diavik kimberlite has major oxide and trace-element concentrations consistent with global averages for kimberlite. The mean total-sulfur content of the kimberlite material is 0.22 wt% S, but with a significant range. The kimberlite has an excess of carbonate minerals over sulfide minerals (average CO2 = 4 wt%, present mainly as calcite), and has a mean neutralization potential of 311 kg CaCO3 equivalent/tonne. A reactive form of framboidal pyrite associated specifically with the mudstone xenoliths is the primary source of sulfide-sulfur. Long-term kinetic tests confirmed the preliminary interpretations that were made from the static-test results. Kimberlite and processed kimberlite are net acid-consuming materials that produce alkaline drainages and have low but detectable leaching rates for SO4 and specific trace metals such as Al, Co, Cu, Ni, and Zn. If segregated from the kimberlite, mudstone xenoliths are acid-generating (pH = 3) and produce an effluent with elevated concentrations of SO4, Fe, Al, Cu, Ni, and Zn. The study demonstrates that xenolithic units in Diavik kimberlites have an important effect on the environmental geochemistry of the ore rock. The mineralogy and aqueous geochemistry of the kimberlite materials are such that they may not be suitable for general earthworks or as an alkaline agent and should report to an engineered facility to protect site water quality."

Jan 1, 2001

By Tom Demorest

SMART is an association of mining companies that meet regularly to coordinate the technology development needed by the mining industry. Since 1995, the member companies and institutions have directed research and influenced the manufacturers and suppliers to improve surface mining technology and services. SMART actively supports learning seminars, collaborative research projects, and user groups. Members of SMART include some of the major surface mining companies in North America and Australia. These companies have recognized the value that collaboration can bring to the needs of individual organizations as well as the global mining industry.

May 1, 2009