Search Documents

By Jodi Wilding, Barry Lurnsden

The implementation of new technology to mineral separation operations requires rigorous testing to confirm the technology&apos;s technical and economic benefit. The Jaguar Mine owned by Jabiru Metals is located in Western Australia and sequentially separates a copper concentrate and then a zinc concentrate. Fine grinding (80% of zinc in tail is <25µm) is required to achieve efficient mineral separation. All mineral losses are therefore fine mineral losses, and so improvements in metal recovery must focus on this fine mineral. Magnetic aggregation technology has been shown to increase the recovery of fine paramagnetic minerals so it was an appropriate technology to evaluate at Jaguar. Testwork commenced in the copper circuit and it was found that there was a substantial reduction in copper in copper tail and an increase in zinc recovery to the zinc concentrate. The increase in zinc recovery in the latter zinc circuit was an interesting result and initiated the second stage of testwork that was to install and test a second magnetic conditioning unit in the zinc círcuit. This showed a further increase in zinc recovery. Magnetic conditioning technology has now been fully evaluated in the plant and is now part of the Jaguar flowsheet.

Jan 1, 2011

By Andrew Dobson, Cheryl Allen, Enrique Acuña

"Totten Mine return air raise was designed with two parallel fans equipped with silencers to reduce the noise emitted from the outlets into the environment. As development and production of the mine progressed through the past years, the silencer system needed to be upgraded, and additional maintenance strategies have been necessary to meet the regulatory noise limits enforced by the province of Ontario. The current mine plan will require the fans to reach the upper limit of their capacity by Q1 2019. To achieve this operational target, additional silencing capability has been required and Totten Mine has explored alternatives to further extend the noise silencing capacity available considering the current constraints at the mine site. The alternatives included a new silencer baffle design and a new layout that have allowed doubling the length of the silencer system. Using acoustic measurement data collected on several occasions, this paper presents and discusses the performance of the various silencing systems which have been installed on the return air fans at Totten Mine.INTRODUCTION Vale Canada Limited’s Totten Mine is a base metal, underground mine extracting nickel and copper, situated in the Sudbury Basin of Ontario. The mine initiated operations at the end of 2013, and is equipped with two main return air fans and two main fresh air fans located on surface. Both fresh air and return air fans are set in a parallel arrangement to operate as integrated units and are equipped with variable frequency drives (VFDs) to allow for the remote modification of their operating set point, usually between 600 to 880 rpm, depending on the mine’s requirements. The main return air raise (RAR) fans are also equipped with dissipative baffle silencers to attenuate the noise emitted to the environment. Approximately four years ago, acoustical measurements conducted to verify compliance with the applicable regulatory criteria, and respond to noise concerns from neighboring residents, concluded that the sound emissions of the main return air raise exceeded the noise design parameters. The acoustic tones of the fans were audible offsite, at a residential location, approximately 9 km northeast of the mine site. The elevated sound levels and offsite audibility was due to degradation of the original discharge silencers from moisture and particulate being drawn from underground workings and passing through the silencer baffles. The audibility was also due to an outlet directivity pattern which directed noise towards the residential location."

Jan 1, 2019

By F. Liu, S. Rezaei, M. Muinonen, M. Barati, V. L. Lakshmanan, S. Marcuson

Canadian nickel-copper ore deposits have been a major source of nickel, copper, cobalt and precious metals for more than 100 years. The two main minerals of interest, pentlandite (Pn, (Ni,Fe)9S8) and chalcopyrite (Cp, CuFeS2), are usually accompanied by large quantities of pyrrhotite (Po, Fe1-xS). Until the 1950s, Po containing small amounts of nickel was routinely smelted as part of the valuable Ni concentrate. The rapid growth in Ni demand following the Second World War created impetus to treat the Po separately. This action would liberate a valuable smelting capacity for higher value Pn, allow for recovery of Ni locked in Po, convert the Fe to iron oxide or metallic iron pellets, and recover S as sulphuric acid or elemental sulphur. The roasting process also has the potential to produce energy due to the highly exothermic oxidation of Po. The Ni industry would then have a “waste-free” process. Both Inco (now Vale) and Falconbridge (now Glencore) developed processes and built large industrial plants for this purpose that operated with some success. But technical issues and tenuous economics were continual challenges. By the early 1980s these industrial operations were closed. Sophisticated froth flotation methods of rejecting Po were developed, and Po containing up to 1% Ni became a waste material reporting to the tailings stream. As part of a major study on possible processing methods of Po for both value recovery and waste remediation, this paper presents a historical perspective on Canadian Po tailings with regards to their generation, inventory, value, and attempts to process them.

Jan 1, 2017

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By Vishal Shukla, Prateek Singh, D. P. Chakraborty

"Continuous thickening by an operation called sedimentation is the separation of suspended solid particles from a liquid stream by gravity settling. The primary purpose of thickening is to increase the solids concentration of the feed stream. High rate thickeners are designed specifically to maximise the flocculation efficiency. A detailed investigation has been carried out to understand the influence of ore type and operating parameters such as bed level, bed mass, rake arm torque and flocculent concentration on thickening operation. Tata steel’s Noamundi plant data shows that variation in ore type, and operating parameters are major contributors to fluctuation in thickener performance. A lot of research has been done earlier on thickening operation but effect of ore type and operating variables by using plant data was never touched before.In this context, the performance of thickener was evaluated by daily data to study the influence of ore type and operating variables on thickener operation. Investigation shows that friable ore % in feed mix is proportional to slime density because friable ore is porous & brittle in nature. As a result, friable ore generates more fines/ultrafine during communition process in wash plant. Increase in flocculant concentration and bed mass is showing a positive change on high rate thickener performance Investigation shows that optimum bed mass and flocculant concentration is required to achieve desired pulp density in thickener underflow at different feed pulp density (g/cc).INTRODUCTIONOver the years, Iron Ore Beneficiation at Tata Steel, Noamundi has seen varied changes. Depletion of high grade iron and with increasing iron ore throughputs coupled with lowering of the hard ore a subsequent increase in slime generation, slime management and clear water requirement for wet Plant has thrown up myriad challenges. To overcome these challenges, many improvements initiatives were taken by Tata Steel in last decade. One of the major changes is the recent High Rate Thickener commissioning at Tata Steel Noamundi to cater the high iron ore throughput requirement. Slime reporting to Thickener has increased from 1.4 MTPA 2.5 MTPA over the last few decades. The above changes further aggravate the poor settling and dewatering characteristics of the slurry which is being feed to HRT. Considering the above mentioned constraints and stringent environmental implication proper water management has become a major challenge to reckon with. The thickener is used to increase the concentration of the suspension by sedimentation, accompanied by the formation of a clear liquid. In most cases the concentration of the suspension is high and hindered settling takes place."

Jan 1, 2016

By W. R. Horn

"WHAT I PROPOSE TO DO is to review or report very briefly and generally on the most important subject areas of environmental concern within the mining industry and to indicate the progress being made. First, however, it seems to me both appropriate and necessary to refer to what I said in an address to the CIM Annual Western Meeting, in November 1971, in Vancouver. At that time, I tried to convey: that the awareness and alertness of this far-flung and diversified industry was sharply on the up-swing; that the knowledge of helpful technology for the abatement of pollution by water and solids was significantly increasing; that most mines were doing something about it; that many had already achieved a recycling of process water to a really significant extent; that progress was being made - though not without considerable difficulty - on the large-scale neutralization and subsequent chemical treatment of acid- and metals-bearing waters; that increasing work was being done by individual mining companies on methods for the vegetation of completed tailings impoundments; and that it had been possible to develop a meaningful estimate of the amount of money to be spent by the industry on environmental control measures during the period 1971-75 (as much as $500,- 000,000 ) . Reference was also made at that time to the constructive work in hand toward the fixation, elimination or dispersion of sulphur from smelters and to the considerable attention which was being given by the indust(y itself toward in-plant problems, e.g., dust and noise. Finally, note was taken of the fact that the inclusion of environmental control costs in the pre-operational financial provisions of new mining operations is now established practice."

Jan 1, 1973

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By G. A. Peebles

"This paper describes the various types of radiometric instruments and the techniques of their operation for grade control, sampling, assaying and probing drill holes at Eldorado Nuclear's uranium mine in northern Saskatchewan. Modifications that have been made to these instruments are discussed, and suggestions are made for the development of more refined and specialized radiometric equipment."

Jan 1, 1969

By Y. Masuda, Y. Nakamura, K. Haraguchi, A. Taniguchi, K. Arita

Availability of the elements originating from steelmaking slag for various marine phytoplankters including purely cultured strains and natural populations was tested in land and shipboard laboratories. The results obtained demonstrate that, although their solubility was not uniform among different slags, dissolved iron, silicate and phosphate from the slag stimulate phytoplankton growth. No negative effect of the slag addition on their growth was observed at lower dose, e.g. less than 200 mg/l. Since most coastal waters are the hypernitrogenous environment due to anthropogenic load of ammonium, the slag can be an ideal source of silicate and phosphate, which restore the hyper-nitrogenous condition into truly eutrophic condition with balanced Redfield ratio. In so-called HNLC (high-nitrate low-chlorophyll) oceanic areas such as the Southern Ocean and the subarctic North Pacific, where iron is almost only limiting factor of the phytoplankton growth, the slag could also be a source of iron and enhance CO2 fixation by phytoplankton photosynthesis. (Key words: carbon deposition in deep-sea, marine environmental remediation, phytoplankton, slag as a source of iron, phosphate and silicate.)

Jan 1, 2004

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By V. G. Papangelakis, I. Guzman, S. J. Thorpe

Pressure oxidation (POX) leaching has been commercially applied to refractory gold ores since the 1980s. In the process, sulphide material is oxidized and dissolved in order to release the gold encapsulated in the sulphide matrix, making the gold available for further recovery. Redox potential is a significant parameter during POX, however it is only measured ex-situ at atmospheric conditions. In-situ redox potential measurement would provide instant information that allowing adjusting the process parameters accordingly. In the present study, redox potential measurements were performed during POX of sulphide material at high temperatures and high pressures. The working electrode was an Ir electrode combined with a flow-through reference electrode in a novel and robust configuration. Experiments were performed in a 2 L titanium autoclave, at 200–220°C, 50–110 psi oxygen overpressure, and 10–30% solids mass fraction. Temperature and oxygen pressure conditions were selected in order to reflect POX of refractory gold ores. Results show that the Ir electrode is consistent with theory and is able to perform well under these conditions, showing promise as a new in-situ sensor.

Jan 1, 2017

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill? has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill? technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill? has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills? are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill? in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

By N. Saeidi

"For a mine section comprising 100 different stoping activities, there are ~10158 different possible stoping sequences to explore in the mine schedule optimization search and this figure is indicative of the challenge posed in maximising profitability through mine schedule optimization. Any viable excavation timetable must satisfy all conditions that will constrain feasible sequences. In general, consideration of additional constraint will tend to reduce profitability. Geomechanical constraints on mine schedules, introduced with the aim of avoiding excavation instabilities, can be established for underground mine schedule optimization processes but, currently, this is done only rather crudely; precedence relations between excavation activities (stoping or development) are encoded to produce particular stope sequence patterns (e.g. ‘chevron’ or pyramidal sequences).The work reported aimed to investigate automated processes for formulation of such geomechanical constraints. The timetable optimization approach to the problem precipitated a fresh look at time dependent, and excavation sequence dependent, deformation. Abundant evidence emerged that supported the notion that any methodology developed that failed to account for such time and sequence dependencies was itself bound to failure. Yet, it was also recognised that any deviation at all from an assumption of linear elasticity for geomechanical numerical modeling, adopted to inform geomechanical constraint formulation, would rapidly lead to impractical levels of computational effort.Thus the approach presented here represents a compromise: the elastic stress fields induced by individual mining activities are computed for each activity, independently considered within a computational domain identical to that of all other activities. These are stored in a database. Instability risk for a specific sequence of mine activities can be assessed through superimposition of stress fields drawn from the pre-computed database. Time stamps allocated to events corresponding to the excavation processes permit the conversion of the sequence of elastic stress fields into a time table of stress fields. For specific locations within the computational domain, the aggregate effect of the sequence of mine activities leads to stress-time histories having a castellated appearance, a result of the near instantaneous response of an elastic medium to the excavation perturbations. Time dependent deformation responses are crudely allowed for through the re-profiling these castellated histories through graphical construction of curved responses, where the curve gradients are related to a viscous parameter. Such curves form the basis for a geomechanical constraint formulation to be adopted for mine schedule optimization."

Jan 1, 2015

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By J. H. Bernard, K. Žák

The three traditional types of Variscan vein Pb-Zn-(Ag) mineralization recognized in the Bohemian massif from historic paragenetic studies are confinned by modem metallogenic studies. Stable C, S, and O isotope data, as well as Pb and Sr isotopic ratios of the deposits, indicate a predominantly crustal origin of the constituents in all three types. Although the data also suggest differences in temperature and pressure of formation, and the oxidation conditions and nature of the hydrothermal fluids, nonetheless they are consistent with prevailing metallogenic classifications of the vein mineralization

Jan 1, 1992

By G. W. Poling, J. R. Hoffert

"A common practice in preventing gravity-fed tailing pipeline from plugging due to sanding is to add lime at relatively high dosage rates. The lime affects the rheology of the slurry ""vehicle"" which transports the coarser particles in a heterogeneous flow-regime. This paper describes a study of the effect of lime on the critical deposition velocities and friction head losses of Highmont Mining Company&apos;s mill tailing. Testwork using an extrusion viscometer was related to the surface chemistry changes brought about by the high lime additions. Lime additions which typically increased the tailing pH from 8.4 to 11.5 reduced the critical deposition velocities from approximately 3.2 to 1.7 m/sec.IntroductionCommon practice, at least in base metal concentrators in British Columbia, is to use high lime additions in tailing slurries when the pipeline becomes partially plugged with sands. Some concentrators, such as the Highmont Mining Co. Ltd. plant, add lime on a continuous basis during low tonnage periods and during startup/shutdown transition s. Although such high lime additions often solve temporary plugging problems, the effect of lime on slurry rheology has not been well understood.Slurry pipelines are designed to transport solids in suspension with a minimum of wear and without particle deposition. These two objectives are in opposition because the velocities required to maintain solid suspension can sometimes cause high head losses in the pipeline, as well as wear problems. Thus, the optimum velocity for a long distance slurry pipeline is in the range that provides just enough turbulence to keep coarse particles in suspension."

Jan 1, 1985

By R. C. Hartviksen

"The Drumbo Mine is a new gypsum mine located at exit No. 32 of Highway 401 between Woodstock and Kitchener, Ontario. The flat-lying 6-foot (1.8-metre) bed of gypsum is near the base of the Silurian Salina Formation, about 380 feet (116 metres) below surface. The mine is owned and operated by Westroc Industries Limited. A shaft, 12.5 feet (3.81 metres) in diameter, was drilled and then lined with a liner-sinking technique new to this continent. The shaft was completed in the fall of 1977. Gypsum production was started in December 1978, employing a conventional room - and - pillar method of mining.Historical BackgroundA brief mention of gypsum in the Drumbo area is included in a survey of the Ontario gypsum industry by Guillet. This occurrence was discovered in 1958 when National Gypsum conducted some widespread diamond drilling. Western Gypsum Products Limited acquired leases in 1960 and concentrated a drilling program in Blenheim Township near the village of Drumbo; 79 holes were drilled in an area of 1900 acres (770 hectares). Mining rights were then acquired for 170 0acres (690 hectares). A test shaft, 44 inches (1.1 metres) in diameter, was drilled to obtain a 50-ton (45-tonne) bulk sample. This opening will be used as an emergency escape way and for ventilation.Westroc Industries Limited, a wholly owned subsidiary of BPB Industries, has its head office at Mississauga, Ontario and operates gypsum board plants at Mississauga, Vancouver, Calgary, Winnipeg and Montreal. Other gypsum mines are at Windermere, B.C. and Amaranth, Manitoba."

Jan 1, 1983

By W. Pietsch

For a number of reasons, solids entering and leaving facilities for the treatment of minerals are becoming increasingly finer. Such materials pose problems throughout processing. Solids featuring small particle sizes tend to dusting, result in losses and segregation, exhibit various storage, transportation, and metering problems, and fine particulate effluents can not be easily captured, used and/or recycled. Sustainable mineral processing must minimize the exploitation of natural resources and avoid the need for disposal of wastes. The first requires the use of lower quality raw materials and upgrading, which typically results in the production of fine grained concentrates, and the latter encourages the recycling of wastes and byproducts or efforts to investigate them as sources for secondary raw materials or other beneficial applications. To overcome the difficulties associated with fine particulate solids, size enlargement by agglomeration is necessary. The resulting products have free flow characteristics, do no longer dust or segregate, and are sized and shaped as required for optimum processing. In addition, agglomerated materials may be engineered to feature desirable structure, composition, and a number of related, improved properties. Such engineering may be applied for the modification of fine run-of-mine and up-graded minerals as well as the production of secondary raw materials from by-products or wastes. By the interdisciplinary application of size enlargement by agglomeration waste-free processing of minerals becomes feasible.

Jan 1, 2004