Search Documents

By Leslie McHattie, Sadek E. EI-Alfy

"The Maintenance Engineering Department at Carol Mining and Concentrating is currently in the process of introducing reliability concepts such as failure analysis, rework elimination, predictive maintenance, computerized maintenance history analysis, etc. to improve the over-all maintenance function in the mine and concentratormaintenance areas. Some current initiatives include:• Implementation ofan infrared thermographic scanning program.• Ultrasonic inspection of shafts for all critical equipment in the mine and concentrator areas.• Non-destructive testing of all major welds done by maintenance personnel.• Development of an effective vibration monitoring and analysis program for the production equipment in the mine (shovels, drills, haulage trucks, locomotives).• Failure analysis performed by maintenance engineers to identify the root cause of component failures on critical production equipment.• Computerized breakdown analysis to identify the recurring component failures which contribute significantly to high maintenance costs and production loss.• Implementation of a computerized maintenance management information system.This paper will outline the planned implementation ofthese initiatives, and others, and will also cover the status and results obtained to date."

Jan 1, 1992

By R. Q. Honaker

A significant problem in ultrafine particle classification is the significant amount of submicron particle by-pass to the coarse particle stream. In classifying cyclones, submicron particle by-pass to the underflow stream can be reduced by decreasing water recovery. Past studies have shown that a reduction can be realized when the feed solids concentration is increased or the apex diameter is reduced. However, both adjustments tend to increase the particle size cut point and negatively affect classification efficiency due to the impact on slurry rheology. The addition of a viscosity modifier to the feed stream of a classifying cyclone improved the classification performance and decreased the particle size cut point over a range of feed solids concentrations. The detailed test program investigated the use of the modifier in conjunction with varying apex diameters to identify conditions that minimize ultrafine by-pass. With small apex sizes, roping conditions were readily eliminated by the addition of viscosity modifiers. The addition of the modifier had no deleterious effect on froth flotation performance, which commonly serves as a downstream separation process. The fundamental and practical benefits of viscosity modifiers in classification processes are discussed in this publication.

Jan 1, 2006

By C. A. Roloff

Demands for increased grinding production, lower-grade are and limited capital have resulted in ever larger grinding mills, some as large as 36ft (/1 m) in diameter and 12,000 hp (8,950 kw). The result is often f ewer machines per plant, with a greater dependence on each machine. To meet these reliability requirements, manufacturers of mills, drives, castings and other components have had to be innovative and creative in their design. Only by thorough review of past designs and practices and by model studies confirmed in field tests can the manufacturer have full confidence in the product. Because of the great interest in large mills, a short review of larger machines is presented. This discussion covers material feeding, bearings, the rotating element, drive trains and material discharge.

Jan 1, 1979

By N. Ahern, D. B. Dreisinger, G. Van Weert

In the thiosulfate leaching of gold, degradation of the thiosulfate reagent is a major cost. One of the intermediary degradation products is trithionate, which also inhibits gold recovery from solution by ion exchange. Little attention has been given to this species in the context of gold leaching - the limited information on trithionate and its solution chemistry available in the literature is seldom directly related to gold leaching conditions. This review is a compilation of the published knowledge on trithionate, with a specific focus on identifying the relevance of this information to gold leaching and the shortcomings in the knowledge base.

Jan 1, 2005

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By Chaluvadi K. Sridhar, Prashanta K. Chatterjee

"IntroductionThe planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc., do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered.Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate man y layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment. Although recent advances in computer graphics have provided the hardware necessary for developing and evaluating min e plans rapidly, software that will allow the mining engineer to make use of the new technology is slow in developing. The need for such software packages has been recognized and ackowledged.At several sessions in recent conferences on the applications of computers in the mining industry, the use and benefit s of computer-aided mine planning were discussed. However, there were few papers presented that referred to actual applications of interactive graphics to underground mine planning. The emphasis of this study is toward the development of a completely integrated computer-aided underground mine planning package that integrates geological modeling, engineering design and planning"

Jan 1, 1986

By M. L. Jeremic, G. J. P Delaire

"The mechanical aspects of cable bolt failure are considered from the point of view of properties of grout and cable, as well as of the rock in which it is anchored. The results from recent investigations made in-situ as well as in the lab are combined and presented with reference to other work done in the area. An attempt is made to stimulate the thinking along these lines so as to initiate further research which may enhance the design of cable bolting as it applied to mining operations.IntroductionIn the past twelve year s systematic cable bolting has found application in many areas. In civil engineering rock anchors have been used to provide tension at the heel of a dam permitting the reduction of its cross section. They have been used in retaining walls to reduce construction time and costs by eliminating the need for struts and braces which complicate pouring the foundation walls. It is also possible to use rock anchors in providing reactions where tall buildings are subjected to uplift on one side due to wind forces. Cantilever bridges may be constructed by implementing rock anchors to provide anchorage requirements. Anchorage piles or dolphins or mooring ships have also been built using these. In the mining area rock anchors, commonly known as cable bolts because they are made of hoist cable may be implemented in the reinforcement of hanging walls or to retain rock slopes.In order to sustain de-pressurized ground where rock separation developed along the pressure arches, cable bolts were utilized at the Tsumeb Mine in South-West Africa and also at the Strathcona Mine in Sudbury, Ontario, In both places old degreased hoist ropes were installed in downholes from crosscuts above a given stope and then grouted without tensioning. Jeremic and Cassidy described the use of cable bolts to increase hanging wall stability and postpone fracturing, in addition to producing pre-support for improvement of stope back stability."

Jan 1, 1983

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986

By James J. Scott

"In the two years since their introduction, Friction Rock Stabilizershave replaced40 per cent of the previously used fixtures in the metal and non-metal mines in the United States. The Friction Rock Stabilizer, or ""Split Set "" , is a mechanical rock stabilizing system which uses friction to prevent rock movement . The Split Set is a tapered, rolled, steel tube that is slotted along its length. As it is driven into a drilled hole smaller than its diameter, it compresses, pre-loading the surrounding rock. This paper discusses the uses and acceptance of the friction rock stabilizer in mines in the United States. IntroductionFriction Rock Stabilizers, commonly called Split Set™· Stabilizers, have been under development by the author and Ingersoll-Rand Company since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977and, to date, over five million units have been marketed to metal mines. The present rate of usage is near 3 V2 million units per year, which is approximately 50070 of all roof fixtures used in the United States metal mining industry,Richard Hoppe, senior editor of Engineering & Mining Journal. , in an article in the February 1979 issue entitled ""Winning the Battle Against Bad Ground"", said: ""In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J . Scott and developed by Ingersoll-Rand Co."" This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of such systems."

Jan 1, 1980

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By A. David MacPhail

"Highland Valley Copper is a large volume producer of copper and molybdenum concentrates. Production is by conventional truck and shovel operation combined with an extensive ore handling in-pit crushing and conveying system.Grade of the two orebodies is low at 0.4% copper and 0.007% molybdenum and this demands a production rate in excess of 260 000 tpd at a stripping ratio of 1: 1. Mining cost has to be kept at minimum levels to keep the mine profitable and thus, it is necessary to keep in the forefront: of technology. As well as the in-pit crushing system, the mine has pioneered the use of shovel weighing coupled with a state-of-the-art dispatch system.Maintenance of the equipment is carried out at the on-site mine maintenance shop with assistance from local shops for engine and wheel motor rebuilds and other large jobs such as those requiring stress relieving. Shovel and truck rebuilds are undertaken by mine crews. Both long- and short-term planning is designed and scheduled in the mine engineering section. Outside consultants are used to assist in slope design, reclamation and blasting technology."

Jan 1, 1992

By C. Van Den Heuvel, C. B. Van Buuren

BIOX® has been successfully demonstrated over the past 2 decades for the recovery of gold from refractory sulphide concentrates. To date 12 successful BIOX® plants have been installed in 8 countries spanning 4 continents with the 13th installation currently nearing completion in the Philippines. In 2010 BIOMIN introduced the ASTER™ process for improved water balances in commercial BIOX® applications by supporting tightening environmental legislation on water usage and availability in both arid and tropical regions. Previously, a common challenge for BIOX® plants was the inability to recycle thiocyanate containing water due to the low tolerance of the organisms. ASTER™, a biological thiocyanate and cyanide destruction process, renders a non-toxic solution for re-use in BIOX®. Two commercial ASTER™ plants are in operation with the 3rd ASTER™ plant under construction in the Philippines. A 3rd BIOMIN technology, specifically developed for double refractory ores is available for implementation. The HiTeCC process has shown considerable success on ores where competition from disseminated carbon has rendered ineffective gold recoveries. Through HiTeCC, gold is desorbed from the carbonaceous matter by manipulating the ionic strength and temperature of conventionally treated CIL product. One Australian commercial plant utilises HiTeCC while a 2nd installation is set for commissioning 4th Quarter 2014. BIOMIN’s premier solutions for refractory gold processing are described herein.

Jan 1, 2014

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By C. T. Dzgoev, S. S. Gudkov, IRGIREDMET JSC, S. G. Schtoick, A. V. Yepiforov, S. V. Balikov, I. I. Yevtuschevich

The pressure oxidation (POX) and pyrometallurgical process comprises POX of gold containing sulfide and polymetallic lead-zinc concentrates prior to reduction smelting of POX products to generate a lead-silver-gold alloy. Refined lead and gold-silver alloys are then obtained using conventional processes. Zinc and other base metals are recovered from the POX solution. In the course of POX, zinc dissolves in the solution and lead concentrates in a solid residue in the form of sulfate compounds. Sulfur forms the major iron sulfates and jarosites. In order to dissolve sulfur and arsenic from solid residues to the solution, the slurry hot curing was carried out at the temperature of 95°C within 2 hours. After filtration of the slurry, zinc was recovered from the solution. The resulting cake was washed with water and subjected to hot alkaline treatment. After alkaline treatment, the cakes were blended with fluxes and subjected to reduction smelting to generate lead concentrate containing precious metals. This concentrate was refined to obtain refined lead and gold-silver alloy. After iron and arsenic were removed from POX solutions using sodium carbonate, zinc was precipitated as carbonate. After thickening and filtration, zinc precipitate was roasted to generate saleable zinc oxide. Using this process, the recoveries of values to saleable products were 97% Au and 95% Ag to the alloy, respectively, 91% Pb to refined lead and 5% Pb to lead and antimony alloy and 94% Zn to zinc concentrate. The features of the technology is that it has high recovery indices of precious and base metals to saleable products and can be used to process various polymetallic ore and technogenic raw materials.

Jan 1, 2016

By K. H. Kretzschmar, M. A. Smith

A brief review of the rapid growth of ACT in Western Canada is presented. It is remarked that this rap-id growth has been accompanied by a heterogeneous approach to design. A more rational and consistent approach is suggested, together with the assumptions on which this approach is based. The operating history of some existing installations is discussed briefly, and conditions necessary for the continued growth of ACT are outlined.

Jan 1, 1960

By Robert B. Parsons

"The annual onslaught of provincial budgets and tax changes is complete, and once again the Canadian taxpayer is being asked to dig deeper into his pocket to fund old and new programs. It is noteworthy that 1987 tax reform promised lower taxes, but a broader fax base. Five years later, we still have the broader tax base, but the lower faxes have gradually crept up to pre-tax reform levels. Surprise! Surprise!IntroductionThe last edition of Tax Notes commented on some important proposals announced in Manitoba's 1992 budget. In this issue, Tax Notes summarizes the 1992 budget proposals of British Columbia, Ontario and Quebec. These budgets reflect the continuing trend of transferring responsibilities and the related costs-from the federal government to the provinces. As well, the budget papers bear witness to the respective governments' political stripes. British Columbia, Ontario and Quebec are seeking higher tax revenues. Only Quebec continues to acknowledge the importance of the mining industry in its annual budget documents."

Jan 1, 1992

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009