Search Documents

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By John E. Udd

The stability of a rock mass is influenced by the presence of discontinuities. In assessing stability, it is required that one should know the frictional and cohesive properties of these contained weaknesses. In the study performed by the authors, a number of samples of diamond drill core containing open discontinuities were tested in shear. The results obtained were compared with values which resulted from back analyses of instabilities in the field.

Jan 1, 1979

By K. D. Eng, W. T. Tierney

"During the past century, the development of vehicular transportation has benefitted tremendously from the performance improvement in engines in a situation where low-cost, plentiful fuel supplies were the order of the day. Engine advances were enhanced by and also dictated fuel modification to better adapt the energy source to the power plant.In discussing the several aspects of the change in approach from ""an engine and its fuel to a fuel and its engine"", the authors touch on the following areas:1. Description of an engine concept that provides the needed flexibility in fuel appetite at good efficiency to cope with future requirement s.2. The constraints placed on liquid fuel resource energy utilization efficiency by special engine-required fuel properties and the fuel efficiency of the various engine types available.3. Future vehicle engine fuel sources. This review will put into perspective the problem associated with the net energy available from future fuel sources under extensive research and development at present.4. A brief review of test data to show that fuel-tolerant and fuel-efficient engines are viable and that, in a fuel-resource-limited future, they can be a ""light at the end of the tunnel.""The Texaco Controlled Combustion System (TCCS)The TCCS is a unique means for stratified charge operation of an internal combustion engine in such a manner as to eliminate the requirement for octane or cetane number specification for the fuel. Octane rating is an empirical engine test method that evaluates a gasoline's resistance to spontaneous ignition or ""knock."" Cetane is based on a different engine test, which determines a diesel fuel's ease of spontaneous ignition . High cetane number enhances cold starting and permits high-speed diesel engine operation. As one would expect, the fuels in current use cover a band when the two values, octane and cetane, are plotted against each other."

Jan 1, 1982

By Lionel C. Kilburn

"This geological engineering method is based on jour main characteristics of mineral properties, viz; location: inclusion of valuable mineralization; inclusion of geophysical and/or geochemical targets; and inclusion of geological targets. These are subdivided into a total of 19 subcategories, which are used to determine the value of the property.The nineteen subcategories are prioritized and assigned relative value factors from 1.3 to 10. Value of each mineral claim unit is determined by applying the appropriate subcategory factors to a base value of $400per 16.2 hectare unit. Property value is calculated by totalling the values of such individual claim-units.The boundary between ore grade and sub-ore grade must be estimated for each property under valuation, thereby making the method sensitive to mineral commodity prices.A clear and disciplined sequence of decisions based on personal experience forms the basis of this method. The method utilizes all factors normally used to value a mineral property.IntroductionIt is generally accepted in the exploration industry that valuation of exploration properties is a subjective rather than objective process (Roscoe, 1986; Lawrence, 1988; Lawrence, 1989; Woodcock, 1985), and that it is greatly influenced by the experience and qualifications of the person who is doing the valuation. However, the significantly low degree of objectivity in mineral property valuation at this point in time invites effort to achieve a more quantitative engineering basis.Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand , and political-economic conditions, all of which vary with time. Therefore, any valuation is valid for only that point in time when it is made. Mineral deposits can decrease as well as increase in technical value with time."

Jan 1, 1990

By N. Ogbonna, D. G. Dixon

Although heap bioleaching has been recognized as an economic alternative for treating low grade mineral ores, the underlying physical, chemical and biological processes involved are complex. A detailed investigation into the dynamics of heap bioleaching processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool - HeapSim. This tool can be of great help in the design and operation of heap bioleaching processes. In this paper, the mathematical model implemented in HeapSim is examined. The model takes into account mineral kinetics, particle level effects, bacterial growth, oxidation and adsorption, gas absorption, pore diffusion, bulk advection, gas balance and heat conservation. Three case studies where the model has been applied are briefly discussed. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists of CIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By D. L. Churcher, R. J. Perry

"In recent years much work has been don e to examine alternate underground backfill support systems with the objectives of improving ground support and reducing mining costs. This report deals with the work conducted at Placer Dome Inc.’s Dome Mine to develop a high density backfill system, taking advantage of the unique properties of this fill material, to address a backlog of large open stopes to sustain stable minewide ground conditions for future generations of Dome miners.IntroductionDome Mine began its existence in 1909 with the discovery of visible gold on a dome shaped outcrop located west of Porcupine Lake in northern Ontario. The orebody beneath this outcrop has supported one of Canada’s premier gold mining operations for 80 years. Production during this time of over 46 000 000 tons of ore has resulted in the recovery of II 500 000 ounces of gold and 2 000 000 ounces of silver. Mining continues today at a production rate of 3500 tons per day, with ore coming from both underground and open pit operations.During the life of the mine, different underground mining methods have been used to extract the ore from a complex deposit consisting of single and multiple vein structures.Cut-and-fill mining was introduced in the 1930s using sand fill and later hydraulic fill for support and to provide a working platform. A total of 1 800 000 tons of sand fill and 7 300 000 tons of hydraulic fill have been placed underground in cut-and-fill stopes. Until the late 1960sshrinkage mining was used extensively, particularly in narrow, steeply dipping zones. Bulk mining with small diameter longholes was introduced about this time, to take advantage of low production costs. Longhole blasting has often been used to recover low grade ore from the walls or sills of old shrink stopes, resulting in large open stopes. Backfilling of these open holes has been restricted to smaller stopes and associated with local ground conditions.In the late 1970s it was recognized that the number of large open holes which were being generated presented serious regional and minewide stability problems for future operations. With higher gold prices, economic ore reserves were being tied up in areas adjacent to multi-level open stope complexes. To stabilize these stopes and allow access, backfilling would be required."

Jan 1, 1990

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By Scott K. Palm, Neil D. Pearson, Jr. Read

"Uncertainty is an important feature of many investments, but it is especially important for mineral properties. Mine properties often entail large investments and fixed commitments. Managers in the mining industry often view price uncertainty as undesirable, due to the possibility that the price of the mined commodity will fall to a level that prevents the firm from recovering its investment and fixed costs. This paper identifies pitfalls in conventional valuation methods and outlines a new approach to valuation based on option pricing theory and dynamic programming. In the process, it identifies generic strategies for organizing mine production in ways that allow the owner to benefit from the uncertainty in mineral prices. IntroductionRisk is pervasive in the mining industry. The operation and maintenance of a mine may involve high, and unavoidable, fixed costs. A mine owner can only begin to recover these fixed costs if the price of the mined commodity is greater than the incremental cost of production. But the prices of many minerals are extremely volatile. The price volatility of copper has been significantly higher than the price volatility of a typical stock, for example. A mine owner cannot be sure that the price of the mineral product will remain high long enough for the firm to recover its capital and fixed costs.Mine owners are able to minimize their losses during periods when the output price is below the incremental cost of production by temporarily closing operations. During these periods they incur only fixed costs. While shut-downs help minimize losses, the y do not help the firm recover its initial investment. If output prices remain low long enough, the fixed costs and original investment may never be recovered. High fixed costs, therefore, lead to substantial downside risk."

Jan 1, 1986

By K. B. Chaudhuri, I. D. Webb, F. E. Rachor, F. A. Sauert

"A characteristic of all methods of copper concentrate smelting is that slags with a high copper content are produced at some phase of the operation. Recirculation to the smelting unit, electric furnace reduction or flotation are at present used on an industrial scale to recover the copper from these slags. This paper describes the application of the top-blowing technique, originally developed by KHD Humboldt- Wedag AG for refining of metallic copper, for the treatment of copper-containing slags. By this method, a mixture of a reducing gas and commercial oxygen is blown onto the melt at velocities which can be supersonic from the tip of a water cooled lance. The impingement of the reaction gas mixture on the surface of the slag forms a depression in the molten phase and a deflection of the jet which brings the slag into a rotating motion. This causes high rates of heat and mass transfer. Results of pilot-plant tests for batch and continuous treatment of slags are presented, and the potential applications of top blowing for industrial-scale operation are indicated. In combination with the cyclone as a smelting unit, this process appears to be economic for smelters of very low capacity."

Jan 1, 1980

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By L. Sun

Recently, micro-tubular solid oxide fuel cells (SOFCs) have attracted the attention of many researchers because of their numerous advantages over larger tubular and planar SOFCs. These include excellent thermal shock properties giving rapid startup/shutdown capability, a high volumetric power density compared to larger tubular SOFCs, and reduced sealing problem compared to planar SOFCs. In order to screen cathode materials for micro-tubular SOFCs, the perovskite cathodes were deposited, using a variety of methods, on 10.5 mol % yttria-stabilized zirconia (YSZ) tubes. Their electrochemical properties were then evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods, based on a three electrode configuration, and with the reference electrode position carefully optimized. The oxygen reduction reaction kinetics at the cathode/electrolyte half cell were then investigated in detail.

Jan 1, 2005

By R. M. Bustin

"Extensive deposits of tectonically sheared coal of the Mist Mountain Formation occur in the south eastern Canadian Cordillera. The quality of the coal varies markedly; it is commonly partially oxidized and poor washability characteristics.Oxidation of the sheared coal has been promoted by its fine grain-size and by fractures in adjacent rocks which have facilitated penetration of atmospheric oxygen and circulation of oxygenated waters. Oxidation has resulted in a loss of coking power, a decrease in vitrinite reflectance, and an Increase In oxygen and decrease in carbon content.The relatively low clean coal yields of the sheared coal are primarily the result of the greater volume of mineral matter present, which in turn reflects both the greater susceptibility to shearing of coal with abundant rock partings and the shearing and dissemination throughout the coal of formerly discrete rock partings. The high ash content of some sheared coal seams may be artificial, resulting from the difficulty in distinguishing and separating sheared roof rock and floor strata from the coal seam during mining. There is little variation between the quality of the washed sheared and unsheared coal, with the exception of the somewhat higher ash content of the clean sheared coal compared to clean unsheared coal. This poorer separation of the ash from the organic fraction of the sheared coal is considered to be a product of the large amount of fines present as well as the local formation of aggregates of organic material and ash resulting from plastic flowage of the vitrite and clarite during shearing.IntroductionIn the southeastern Canadian Cordillera, coal seams of the Lower Cretaceous Mist Mountain Formation (Gibson, 1979 were in part sheared and comminuted during Late Cretaceous and Tertiary tectonism . Extensive deposits of sheared coal exist, and even in areas of mild deformation the coal may be locally sheared (Bustin, 1979). The quality of the sheared coal varies notably; it is commonly oxidized even far from the present weathering horizon, and locally has a disproportionately large amount of ash and poor washability characteristics even far from the present weathering horizon and locally has a disproportionately large amount of ash and poor washability characteristics."

Jan 1, 1982

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By K. B. Culver

"This paper provides background information on the expansion programs of Rio Algom Limited at Elliot Lake. Included are details on the Quirke expansion program, the Panel mine rehabilitation program, including the selection procedure for the tailings containment area, the Stanleigh mine rehabilitation program, housing, government regulations and the Environmental Assessment Board hearings. Introduction After 2Y2 years of public hearings, 4 years of arbritrating differences of opinion between our engineers and government licencing authorities, interspersed with research into radium removal and development of the LAMIX process and carrying out the work associated with some 24 control orders issued to us by the MOE, it is very difficult to compress all of the experiences and frustrations into a single paper. The highlights, as they relate to the expansion programs of Rio Algorn Limited and its affiliate, Preston Mines Limited, will be covered. Denison Mines Limited, of course, is the other uranium producer in Elliot Lake. They are currently in the process of expanding from 7,000 to 11,000 TPD by the second half of 1980 and then to 15,000 TPD by the mid 1980's. In giving this overview, the following seven items will be discussed: • The basis for Rio Algom's and Preston's expansion plans. • The Quirke Expansion. • The Panel Rehabilitation. • The Stanleigh Rehabilitation. • Housing Programs. • Government Licencing Requirements. • Environmental Assessment Board Hearings."

Jan 1, 1980

By P. D. Hanson, H. Colijin

"New procedures and techniques are now available for the design of bulk storage bins. These new methods have essentially eliminated guesswork in the gravity flow of bulk solids, and have provided a sound basis for the quantitative analysis of alternate designs of hoppers and bins. This paper will discuss the practical application of the Solids Flow Theory (Jenike & Johanson) and illustrate the required design procedure with a few examples of actual bin operations."

Jan 1, 1970

By Brian Mattie

Overview ?Overview of the mining area ?Description of the mining phases ?Risk assessment ?Design criteria and description for freeze drifts ?Freeze wall design ?Raisebore mining Four Main Phases: 1.Development of freeze drifts on the 520 and 590 levels 2.Freeze drilling and ground freezing to isolate the Zone 4 North ore body from water bearing sandstone. 3.Develop raisebore and extraction chambers including access drifts and ramps under freeze protection. 4.Start raisebore production mining of the Zone 4 North area.

Nov 1, 2011

By L. Sun

A numerical model has been developed to study the air flow in the flow plate and gas diffusion layer assembly on the cathode side of a PEM fuel cell. The flow plate in this type of fuel cell often has serpentine channels and the porous layer is adjacent to the flow plate to diffuse the air to the catalyst layer. Flow cross-over of air through the porous diffusion layer from one part of the channel to another can occur. This flow cross¬over is a result of the pressure differences between different parts of the channel, and it causes the flow rate through the channel to vary with the distance along the channel. A numerical study of pressure distribution and flow cross-over through the gas diffusion layer (GDL) in PEMFC flow field using a serpentine channel system has therefore been undertaken to compare the cases of a single channel and two parallel channels, with the channels having a trapezoidal cross-sectional shape. The purpose of the present work was to study the effect of the flow plate geometry on the basic fluid flow through the plate. The flow here has been assumed to be three-dimensional, steady, incompressible, isothermal and single-phase. The flow through the porous diffusion layer has been described using the Darcy model. The dimensionless governing equations have been solved by using the commercial CFD solver, FIDAP. From the results obtained, it can be found that the single channel systems have greater maximum flow rate difference than the parallel channel systems under the conditions considered in the present study. Also, the size ratio R of trapezoidal cross-sectional shape has a significant effect on the flow cross-over and pressure variation in the flow field.

Jan 1, 2005

By C. A. Pickles

Microwaves are being applied industrially in a number of fields and possess a number of potential advantages that could be applied in extractive metallurgy. Microwave heating has a number of unique characteristics, which distinguish it from the conventional heating methods. In microwave heating, the absorption of energy occurs at the molecular or atomic level and therefore the heat is generated within the material itself. In conventional heating, the exterior temperature is usually higher than the interior, but with microwave heating, the temperature gradient is inverted and thus the interior temperature can be much higher than that of the surface. The energy densities in microwave systems can be relatively high and this in combination with the low thermal conductivities of oxide ores, can lead to very high internal heating rates. In this research, the application of microwave energy for the reduction of a nickeliferous silicate laterite ore has been investigated. The real and imaginary permittivities are the two fundamental properties which determine the microwave absorption characteristics of a material and these were measured for the ore, both with and without carbon additions using the cavity perturbation technique. The microwave heating and reduction experiments were performed in a 0 to 2 kW CTC microwave system. The effects of power input, processing time, sample mass and charcoal additions on the microwave absorption were investigated. Then reduction experiments were performed and the nickel grade of the magnetic concentrate and the nickel recovery in the concentrate were determined.

Jan 1, 2005