Search Documents

By A. A. Rafiei, J. A. Finch

A previous study comparing n-pentanol and the polyglycol Fl50 showed that the two reagents could give the same gas holdup but with different size bubbles. The finding implies that bubble rise velocity depends on the surfactant (frother) type. A study using bubble swarms supported the frother type effect but bubble interactions were a possible confounding factor. This study resolves the question by measuring the rise velocity of single bubbles of 0.8-2.5mm diameter over a distance :::: 300cm in n-pentanol and F 150. It is shown that at typical frother concentrations used in flotation that the rise velocity in n-pentanol remains comparable to that in water alone while in Fl50 the velocity is significantly reduced. The results confirm the suspected impact of frother type. It is illustrated that in n-pentanol the rise velocity does not reached terminal; while in Fl50 it does and this is the source of the velocity difference. Advances

Jan 1, 2009

By A. M. Bell

"Hallnor mine is in the township of Whitney, Porcupine district. To date, its production of gold has been second largest in the east Porcupine field. Ore was discovered in the property in 1936 by diamond drilling in overburdened country. This drilling was undertaken by Noranda Mines following the discovery of ore in conglomerate at Pamour 1 mile to the east.Milling commenced at the Hallnor in June 1938, and to the end of 1945 432,000 oz. gold had been produced from 889,000 tons of ore, giving an average recovery of 0.49 oz. a ton.The West mine of Pamour, the Broulan orebody, and the veins on the Hallnor and Bonetal are all parts of a mile long vein system that has been separated into three sections by cross faulting. In consequence, they could well have been described in one paper. In treating them individually the viewpoint obtained from each may lead to conflicting opinions, and any conclusions advanced in this paper on the general structure should be modified by the conclusions advanced in papers on the neighbouring properties.GENERAL GEOLOGYRock FormationsThe Hallnor orebodies occur within 400 feet of the contact between lavas and sediments, and may lie in either lavas or sediments. The lavas near the ore consist of flows of pillowed andesite and one flow of more acid and less sheared and chloritized lava locally named trachyte. These flows strike east-west and dip steeply. At the surface on the east side of the property the volcanics have been intensely altered to a massive carbonate rock having a north-south thickness in excess of 1,000 feet . This carbonate body extends west across the property with a plunge of 45° (Fig. 1)."

Jan 1, 1954

By Takashi Nakamura, Atsushi Iizuka, Yong Fan, Etsuro Shibata

Magnetic separation of precipitated magnetite as iron resources in copper slag is one of the potential effective ways to recycle the slag. It is preferable to convert molten fayalite slag after copper smelting process to magnetite slag via oxidation. With a TTT (Time-Temperature-Transformation) diagram, the crystal composition of the slag obtained after air isothermal oxidation could be estimated through a designed cooling path. The crystallization behaviors concerned with molten oxidation was studied for better understanding of the trade-off relationship between magnetite and hematite during molten heat treatment. Moreover, a brief consideration was implemented of the reaction mechanism.

Jan 1, 2014

By Martha Gellner, Lutz Wuschke, Hans-Georg Jackel, Urs A. Peuker

"Electric vehicles are an alternative to the existing combustion engine driven cars. According to the EU Battery Directive a substantial recycling rate of at least 50 wt.-% has to be met for aged batteries since 2006. Existing recycling techniques are based on energy intensive pyro- and hydrometallurgical process, which are not able to recover all components. Aluminum and lithium for instance are slagged. The EU-Project “ABattReLife” investigated possibilities for a mechanical processing in order to create a sustainable process and a closed material loop from grave to cradle. After a sufficient liberation of the Li-ion batteries, components like the doped carbon black fraction (mainly lamination of electrode foils), the separator foil and the housing material can comparatively easily be separated from the other components by screening and air sifting. The remaining mixture consists of anode and cathode foils which have a similar free-settling ratio and are more difficult to separate from each other. A second comminution and compaction step modifies the particle size and shape as well as the degree of delamination. These changes influence the density of the electrode foils in order to improve the separation efficiency. Yield and purity of the generated metal concentrates were parameters to show if the separation was successful. The specific energy consumption for the different methods of processing was estimated in order to benchmark the cost-benefit ratio for each one.The studies have been accomplished with a zig zag sifter (model TUBAF), a hammer mill (model HM 340 Jehmlich) and with a Petkus-Sifter. Finally a process flow sheet was developed for a Li-ion battery recycling plant in pilot scale."

Jan 1, 2016

By J. Severin

Surface mining operations are increasingly involving the design and development of deeper and larger open pits, often with plans to transition into underground mass mining operations. Experiences at the Palabora Mine in South Africa demonstrate the complex interactions between underground workings and the steep slopes above that may lead to slope movements that potentially pose safety and economic concerns. To properly assess the rock mass response to these interactions for planning of future developments, understanding the controlling influence of geological and geomechanical structures is crucial. Preliminary results are presented from a detailed review of historical slope monitoring data from the Palabora Mine, before and after the initiation of block caving 400-m beneath a 800-m deep pit. This paper demonstrates that a detailed analysis of geology and monitoring data can be used to better understand the kinematic controls of complex rock slope displacements and interactions between open pits and underground mines. This investigative treatment of the monitoring data is important in understanding the failure mechanisms prior to undertaking sophisticated 3-D numerical models.

May 1, 2009

"A growing public awareness of work-related diseases such as pneumoconiosis and the impact of this awareness on legislative bodies and on the skilled labour market are reasons why the Canadian mining industry must consider dust control of top-drawer importance. Measurements and standards related to the hazard are necessary to control a dust situation and to avoid excessive risk. The author discusses some of the methods of measurement, standards proposed and terminology used in this developing technology. The purpose primarily is to give a better understanding of the basic advances achieved by those who have applied current knowledge with a measure of success."

Jan 1, 1972

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By S. Ng, Peter Stapleton, Paul Mankowski, J. Spence, R. Siy

"Syncrude has developed a low energy extraction process for the recovery of bitumen from oil sand. This new process operates at a temperature of 25 °C, resulting in substantially lower energy costs and lower capital costs, especially for the thermal energy generation equipment. The process will be used in Syncrude’s Aurora Mine, which is scheduled for startup in mid 2000. The flowsheet for Low Energy Extraction includes hydraulic transport of oil sand slurry, and bitumen separation using collector and frother chemicals and air as process aids. A number of flow sheet innovations and optimizations have been included, resulting in the next generation of extraction technology. Experimental pilot plant results, engineering progress to date and areas of ongoing work will be discussed. SUMMARYThe Low Energy Extraction Process has been successfully developed for commercial implementation at Aurora. The 1996 100 tonne hour Field Pilot demonstrated that the bitumen recovery target could be met with an 11.1% grade oil sand. However, pilot plant bitumen recoveries for a lower grade oil sand were not acceptable. The subsequent flowsheet optimization study led to a new flowsheet for Low Energy Extraction, which includes a primary separation vessel, a flotation circuit for PSV middlings, and the use of middlings displacement in the PSV cone bottom with flotation underflow. A test program conducted in 1997 showed that the new flowsheet could significantly improve the bitumen recoveries for lower grade oil sands. Engineering work on process scale-up led to selection of a 30 meter diameter PSV, with a tangential feedwell. The successful development and commercialization of Low Energy Extraction for the Aurora Mine Project is a major enabling step in the Syncrude 21 program. The low energy requirements of this process allow Syncrude to develop the Aurora leases more cost effectively. The use of this process results in major capital cost savings, predominantly in the thermal energy infrastructure and also provides long term operating cost advantages for Syncrude."

Jan 1, 1999

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By D. T. Smith, S. J. Strohmayr

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill™ has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill™ technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill™ has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills™ are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill™ in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal

In copper Eta plants the optimal current density setpoint depends on the electrolyte composition and temperature. However, conventional plants operate with large standard deviations. A value of 14% with current densities offsets up to ±50% is typical. For worst, during opencircuit or shortcircuit events this variation can be from -100% to +200%. Naturally, energy consumption and copper quality are compromised. Several devices have been successfully employed to reduce set point deviations. Last developments include; Optibar Segmented Intercell Bars, Outotec Electrodes Arranging Method and NTC Selective Electrodeposition Enhancers. This paper researches and compares these technologies. It is shown that short circuits can be effectively reduced in occurrence and magnitude. Moreover, 95% of the electrodes can be forced to operate within ±10% of the set point. The specific energy consumption is reduced from 2,000 KW per Ton to values close to 1,900 KW per Ton.

Jan 1, 2011

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005

By J. Manchisi

This study has investigated the use of blast furnace slag as functional adsorbent for metal ions in acid mine drainage treatment. This opportunity has not yet been developed into a practical process partly because of limited understanding of rates and mechanisms of adsorption process and inconsistency in interpretations of adsorption data. The overall objectives were to determine the efficiency and mechanisms of sorption process of metal ions in a multiadsorbate system. We employed standard materials characterisation techniques to analyse composition, structure and surface morphology of the slag. Batch adsorption experiments were then conducted to study the mechanisms, kinetics and efficiency of metal sorption as a function of pH, phase ratio, mixing time, mass and particle sizes of slag. Both XRF and adsorption data suggested the slag to possess acid neutralising capacity. This slag is non-crystalline based on XRD pattern, has adequate porosity and pore volume comparable to similar commercial adsorbents but it has inferior pore structure, pore size distribution and BET surface area to be effective under wide applications. Metal sorption increased with decrease in slag particle diameter, decrease in initial metal concentration and increase in the mass of slag. Although slags have demonstrated to efficiently treat low concentrations of single and multiadsorbate effluents using fine particle sizes, they have limited capacity to treat multiadsorbate systems for some metal ions. This is probably due to low affinity, competitive adsorption or limitation in material?s adsorptive properties. Sorption mechanisms probably involve precipitation and ion exchange on the basis of alkaline pH and exchangeable slag surface ions. Sorption preference is proposed as Fe2+>Cu2+>>Cd2+>Co2+>Mn2+. Despite these limitations, deeper understanding of sorption behaviour of metal ions by slags for application in dilute and large volumes of effluents is necessary where precipitation and other standard techniques are either inefficient or uneconomic. Thus, this study has established that sorption capacity of slag to remove metal ions from acidic effluents is selective, limited to certain metal ions and for other ions only at low concentrations. Further adsorption studies in multiple solutes under various experimental conditions or those that can propose an economic slag activation process are needed that improves or widens adsorption window.

Aug 1, 2013

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005