Search Documents

By Steve Piercey

Introduction ? VMS Deposits: The Target ? Key points for every belt: heat flow and extension. ? Good felsic rocks ? Good mafic rocks. ? Petrochemical assemblages. ? Summary Key Points Throughout ? Common themes: ? Heat ? driver of the hydrothermal system ? Extensional geodynamic setting ? conduits to focus fluid flux ? (e.g., Lesher et al., 1986; Swinden et al., 1991; Barrie et al., 1993; Lentz, 1998; Syme et al., 1999; Piercey et al., 2001, etc.) ? We must identify rocks, belts and tectonic environments that encompass these two criteria (among others but?) ? e.g., forearc rifts, intracontinental rifts, arc rifts, and back-arc basins.

Apr 1, 2005

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011

Oct 1, 2010

By T. Sugawara, S. Hara, Y. Mitsui

Surfaces of rock slopes in cold regions often become frozen in winter. Therefore, understanding time-dependent behavior of frozen rock, as well as that of unfrozen rock, is important for long-term stability assessment of rock slopes. In this study, a series of uniaxial compression tests and creep tests were carried out on Shikotsu welded tuff under dry and water-saturated conditions at -20 °C to clarify timedependent strength and deformation of the frozen rock. The influence of water content on them also was investigated. It was found that the amount of deformation of the water-saturated specimen was much greater than that of the dry specimen. It also was found that the creep behavior of the water-saturated specimen was similar to that of polycrystalline ice. These show that deformation of the water-saturated specimen is strongly affected by pore ice. The UCS of the water-saturated specimen was approximately equal to that of the dry specimen at a strain rate below 4.2×10-6/s, and its value was about 17 MPa. However, the former increased up to 26 MPa at 4.2×10-4/s with loading rate, whereas there was little increase in the latter. This means that the UCS of the water-saturated specimen was always greater than that of the dry specimen at higher strain rates. The creep life of water-saturated specimens was longer than that of the dry specimens at stress level greater than 15 MPa. These results of UCS and creep life show that inclusion effect due to presence of pore ice plays an important role on strength of the water-saturated specimen. Creep life of the non-failure specimen that was loaded for more than three days was estimated by the relationship between creep life and axial strain rate at 10 s on failure specimens. It was found that creep life of the water-saturated specimens was shorter than that of the dry specimen at stress levels less than 14 MPa. This suggests that estimation of creep life of frozen rock under water-saturated condition is important for the stability assessment of frozen rock slopes. It was clear that the loading-rate dependency of UCS was related to the stress-level dependency of creep life in both dry and wet conditions. This indicates that there are common fracture mechanism in creep and uniaxial compression tests. It also indicates that the creep life can be estimated by the relationship between the UCS and the loading rate. The time dependencies of the water-saturated specimen were in good agreement with those of polycrystalline ice. This confirms that pore ice strongly affects the strength of the water-saturated specimens as, well as the deformation behavior.

Jan 1, 2015

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick 's 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province' s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province' s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province's plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec's progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By L. Rosato

In the past decade, as a result of increasing iron loads, Canadian Electrolytic Zinc (CEZinc) has become a pioneer in understanding the critical factors that affect the roasting of concentrates with high pyrite contents as well as those factors governing the effects of high iron loads on the leaching circuit. De-bottlenecking efforts in the roaster and acid plant section of CEZinc have given rise to a better appreciation of the impact of iron on roaster productivity. High standards for impure solution quality, zinc recoveries and residue disposal have all led to an increased comprehension of the limits of the leaching circuit and the optimization potentials with respect to iron and ferrites. In this paper, the impact of iron on the roasting and leaching circuits of CEZinc will be reviewed and special emphasis will be given to some of the more recent process optimization and improvement activities.

Jan 1, 2006

By Ian S. Leslie

Seismic monitoring systems for mining operations are being utilized more than ever before in the characterization of rock mass response to underground and open pit mining. This paper provides a review of the use of microseismic monitoring for rock mechanics applications at mines throughout the world. Some practical considerations for the installation of these systems are presented along with techniques for optimizing seismic array coverage. Case studies and installation examples are also provided. Recent applications of advanced seismic analysis techniques are discussed including the determination of event mechanisms, mapping of maximum peak particle velocity (PPV) and seismic hazard fields, and the use of source parameter data for large event re-entry protocol.

Jun 1, 2012

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014

By Maria Skyllas-Kazacos

The All-Vanadium Redox Flow Battery that was pioneered and has been developed at the University of New South Wales (UNSW) in Sydney since the mid-1980s is currently regarded as one of the most attractive energy storage systems for large-scale implementation in a wide range of grid-connected and offgrid applications. Several companies are now manufacturing and installing MW-scale VFBs in applications ranging from renewable energy storage, load-levelling, emergency back-up power and power arbitrage. The full-scale uptake of the VRB in commercial energy storage systems however, is heavily dependent on the availability and cost of vanadium used in the VRB electrolyte. Cost is also a function of purity requirements and although there is little scientific evidence on the effect of impurities on the VRB life and performance, VRB developers continue to demand high purity vanadium at considerable cost. This paper will provide a brief overview of the current understanding of electrolyte impurities on VRB performance together with an economic analysis of the impact of vanadium prices on overall VRB capital and levelised costs for a range of applications.

Jan 1, 2014

By Niels Verbaan, Ron Molnar, David Dreisinger

"An acidic chloride leach solution was generated from the treatment of an ore containing the following value elements: silver, gold, indium, gallium, copper, zinc and lead. Iron was also co-extracted into solution as a ferric chloride species. Iron extraction was a significant component of the overall acid consumption of the leaching process. The recovery of iron by solvent extraction and water stripping was investigated. Tri-butyl-phosphate (TBP) was very effective at recovering iron from the leachate. The water strip solution could be decomposed to produce ferric oxide (hematite) and hydrochloric acid for recycle via hydrothermal hydrolysis or pyrohydrolysis.INTRODUCTION The Malku Khota deposit is situated in the eastern part of the Bolivian Altiplano at elevations between approximately 3,800 and 4,580 meters above sea level (Figure 1). The project is located 98 km east-southeast of Oruro, and 85 km south of Cochabamba in a relatively remote area."

Jan 1, 2016

By Carlos Antônio de Morais, Renata Dias Abreu

The present work describes a study of the separation of terbium and dysprosium from heavy RE concentrate through a solvent extraction circuit in a counter-current system. As the efficiency of the REE extraction by acid extractants rises with the increase of the atomic number of the element, the aim of this work is to extract the elements with higher atomic number maintaining Tb and Dy in the aqueous phase. Thus, terbium was separated first with subsequent separation of dysprosium. The experiments were carried out by using IONQUEST®801 as the extractant and a REE-hydrochloric liquor as feed solution. The optimum operational circuit in terbium separation was comprised of 37 stages: extraction, scrubbing, stripping, and solvent washing. For the dysprosium separation 39 stages were required. Terbium separation over 92% with over 95% purity and a Dy separation over 97% with over 95% purity were obtained.

Jan 1, 2014

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

By R. S. James, D. C. Peck, P. T. Chubb

"The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered mafic intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendriticpegmatitic mafic pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and magmatic breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to 100/0 within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that affected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd:Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Several factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic interaction with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion.The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril&apos;sk-Talnakh region, Siberia; Duluth Complex, U.S.A.) in terms of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economic concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginaltype POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By Stewart A. Ferguson

Location.-The property consists of eight claims (P-12339 to 12343, 12403 to 12405) in Robb township, adjoining Jamieson township on the west. A mocor road extends twenty-two miles northwest from Timmins to the mine. Acknowledgments.- The field work was done in 1940 and 1943, while the writer was employed by the Ontario Department of Mines. The Metals Reserve Company has made available information regarding the property through Messrs. W. R, Dunbar, of Hollinger Consolidated Gold Mines, and W. C. Ringsleben, of the Metals Control Board, Department of Munitions and Supply.

Jan 1, 1945

By D. A. Brown, C. Lowe

"Abstract -A multi-sensor (electromagnetics, magnetics, gamma-ray spectrometry, and VLF) geophysical survey was recently conducted in the Purcell Basin of southeastern British Columbia in an area encompassing the world-class Sullivan Sedex deposit. The purpose of the survey was to geophysically characterize the known mineral occurrences and to develop strategies to enhance future mineral exploration in the basin. Follow-up investigations of geology and measurements of rock physical properties helped constrain interpretations of the geophysical data sets.Despite extraction of more than 90% of the ore from the Sullivan deposit, it is clear that the mineralization there, as well as at other Sedex occurrences surveyed, is characterized by high conductivity values, strong bedrock conductors, and elevated magnetic anomaly values. The albite-sericite alteration which accompanies this mineralization yields high potassium and low thorium-potassium ratio values. Associated Moyie gabbro is characterized by low electrical conductivity and radioelement concentrations and by high magnetic anomaly values. The study has also aided exploration for other mineral deposit types including stratabound Cu-Ag, placer gold, vein and disseminated basemetal deposits. In addition, the geophysical data have helped constrain geological interpretations of the basin."

Jan 1, 1998

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the present study, the dynamic response of AZ and AE cast magnesium alloys to shock loading, are compared for strain rates ranging between 900 and 1200 s-1. Texture measurements showed that after shock loading, the (00.2) basal texture component of both alloys was strengthened. However, the strengthening magnitude was higher for AE samples. Also, it was observed that the twinning fraction decreased in both alloys with increase in the amount of alloying elements. In addition, cracks are formed at the interface between matrix and second phase particles in the AZ alloys. However, crack nucleation and fracture in AE alloys occurred at the sites where twins accumulated. Furthermore, analysis of the dynamic mechanical behaviors showed that the ductility of AE grade is higher than that of AZ alloy for all strain rates used in this research. This difference was explained by differences in deformation mechanisms of these alloys.

Jan 1, 2014

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of&apos; motors, and motor and equipment bearings. With today&apos;s digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system&apos;s performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By H. R. Taylor

The history and development of this property is more or less familiar to nearly everyone connected with the mining industry, so that only a brief outline of the more important facts will be given in this article. In 1916, a small pilot mill was constructed by the British Columbia Copper Company at Copper Mountain, and during 1916 and 1917 test work was conducted to determine the possibility of concentrating the ore and also to work out a suitable flow-sheet. In the spring of 1917, the location of a mill site at Allen by, which is about 8,% miles from Copper Mountain, and near the Similkameen river, was decided on, and the designing of a 2,000-ton plant was then worked out by Bradley, Bruff and Labarthe. Early in 1918, the actual construction of the concentrator began, and, after considerable labour difficulties, it was completed in 1920. During this period of construction, the West Kootenay Power Company ran a 60,000-volt power line over from Greenwood, a distance of 102 miles, and also built a sub-station at Allenby to take care of the mine and mill. The concentrator was started up on October 20th, 1920, and ran until December 11th, 1920, a total of 18,354 tons of ore being milled. The results of this short period of operation were encouraging, but, due to tlie prevailing low price of copper and high wages, it was necessary to shut down until a more favourable time. During the latter half of 1923, some work was done on remodelling the mill. This work continued until January 8th, 1924, when it was suspended.

Jan 1, 1929