Search Documents

By H. Clare Horwood

"Two structures, a fracture zone and a shear zone, contained the two orebodies that yielded all the ore mined at the Gold Eagle mine. The orebodies are known as the Gold Eagle vein and the No. 1 shear zone. Both structures occur close to contacts between Timiskaming sediments, Algoman diorite, and later Algoman granite-granodiorite. The structures were produced by compressive forces from a south direction acting in the southern part of the McKenzie-Gold Eagle stock and in a cylindrically shaped inclusion of Timiskaming sediments.The mine, which exhausted its ore reserves and ceased operations in September of 1941, is on the east side of Mackenzie island, in the centre of Dome township in the Red Lake area.The Gold Eagle vein was located during the summer of 1933 by a surface exploration programme carried out under the direction of Alex Gillies. Sub-· sequent diamond drilling and underground exploration led to the installation of a mill, which came into production in October of 1937. The No. 1 shear zone was discovered and explored later from a drive on the 500-foot level. The mine produced a total of 40,204 oz. gold and 19,157 oz. silver from 223,628 tons of ore hoisted (180,095 tons milled) during its 4 years of mill operation.GENERAL GEOLOGYThe ore-bearing structures trend S.61°E. across Timiskaming greywacke, Algoman diorite, and later Algoman granite-granodiorite. The greywacke is a large, cylindrically shaped mass that is separated from the mai~ mass by the later intrusives. It is a massive, light-coloured, quartzose variety that has been recrystallized by the enclosing granite. The diorite and the granite-granodiorite are early and late components of the McKenzie-Gold Eagle stock. The diorite, which is a porphyritic rock containing large crystals of andesine-labradorite surrounded by hornblende, was injected early in the Algoman period. It was intruded and in large measure surrounded by the later granite-granodiorite. This rock varies from a granodiorite near the mine to a granite in the centre of the stock. All three intrusions are massive and homogeneous."

Jan 1, 1954

By Patrick R. Taylor, T. A. R. Putra

A review of various methods to treat high arsenic copper concentrates through pyrometallurgical processing is presented. Examples are drawn from various past and current operations and research. Various aspects of the engineering alternatives for treatment methods are discussed. Some of the methods discussed include: controlled oxidation roasting, adaptation of some smelter technology to accept higher amounts of arsenic, complete oxidation with arsenic fixation; sulfation roasting; acid baking, soda ash roasting, and others methods. Other topics include: a short discussion of other problematic impurities; the effects of arsenic on copper electro-refining and product purity; and methods for the ultimate disposal, or marketing, of the arsenic. The latest work being done at the Colorado School of Mines on soda ash roasting is also presented.

Jan 1, 2014

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

By C. J. Li, J. L. Feng

In the present study we focuses on developing the poroelasticity model that deals with adsorptioninduced permeability change mostly occurred in porous media constituted several phases such as coal. The underlying pressure induced by adsorption is obtained by Virial expansion form, which is substantially founded on statistical physics. The corresponding thermodynamic pressure applying on the pore surface is then used to detail the pore pressure and further to evaluate the macroscopic volumetric strain and the porosity. In the process of physical adsorption, the adsorbed phase is in thermodynamic equilibrium with the gas phase regardless of pore size, and the corresponding chemical potentials are all equal. The relationship between surface strain and volumetric strain is derived under infinitesimal deformation conditions to gain an explicit formulation of pore surface area with respect to volumetric strain and porosity. After the formulation of surface stress modified by the Langmuir isothermal adsorption is derived, the differential micromechanical constitutive equations of porous media are obtained. By supposing that the ratio of current permeability to initial is equal to the cubic ratio of current porosity to initial porosity, the differential equations for permeability change is consequently derived. The numerical simulations by the present model for permeability change of coal induced by adsorption of CO2 and CH4, respectively, are presented under confined stress conditions. The predictions from the model are good in agreement with the experimental data of sorption-induced permeability change of coals in the literature.

Jan 1, 2015

By T. Negeri, M. Boisclair, A. Bouajila

CanmetMINING has been working on process development for separation and concentration of rare earth bearing minerals from various ores. Among others, the flowsheet development for the Montviel Rare Earths/Nb deposit, located at the north end of the Abitibi region in Quebec and owned by GeoMegA Resources Inc. (GeoMegA) is now at an advanced stage. The concentrate produced by a flotation-only process at the early stage of the project accounted for higher than 90% TREO and Nb recovery in 40% mass. This concentrate was submitted to SGS Lakefield for hydrometallurgical processing. Lixiviation of the concentrate using hydrochloric acid yielded approximately 99 % REE. An overall (from ore in ground to final precipitate) REE recovery of 80% was obtained through a series of selective precipitation steps. Recently significant additional developments have been made. CanmetMINING is steadily improving the quality of concentrate produced through a simplified, more efficient flowsheet which consists of flotation, magnetic separation, and a thermal treatment procedure. The paper discusses aspects of the process that allowed obtaining 82% recovery of TREO and Nb in 16% of mass, the best result to-date.

Jan 1, 2014

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By H. A. Steane

THIS BRIEF PAPER presents the information available on the use of Dorrclon?is in the middling re-grind unit at the lead-zinc mill of Canadian Exploration Limited. The plant throughput is 1,650 tons per twenty-four hours. The flotation feed is ground to 60 per ?Cent passing through 200 mesh. It contains some composite 11articles of sphalerite in calcite, and these reported either in the final zinc concentrate, thus lowering the grade, or in the tailing, with loss of zinc. The re-grind unit was set up in the zinc flotation circuit to liberate the sphalerite from these middling particles, to raise the grade of concentrate and improve recovery. Grinding through 325 mesh should give substantial liberation of locked sphalerite. The middling regrind unit consists of two Dorrdones and one ballmill arranged as shown in the -accompanying flow-sheet. The Hardinge ball-mill, size 7 ft. x 36 in., was free for this use as a result of recent plant expansion. The two Dorrclones were purchased, and the necessary pumps and pipe lines were installed to complete the regrind unit. The unit has been developed over a period of two years by several steps and various flow schemes until reaching tl1e present flow scheme. These steps are not elaborated here, because the changes were made to determine the best product to work on for flotation metallurgy, and not because of the Domrolone classifying ability.

Jan 1, 1956

By O. Kodym

The paper has focused on possibilities of interconnecting information sources concerning monitoring & control of mining industry technical processes (TP), and the related safety hazards. The key issue is the comprehensiveness of the information presented to users. Information can be presented by virtual reality means, when the seemingly true presentation of the production process scene along with user friendly presentation of related information is available. The user in its role of a process supervisor is not only a mere scene observer but, thanks to the interactive functions of virtual environment, he participates in the scene of his control. As such his control and management abilities increase because he can absorb, more easily understand and asses the information provided.

Aug 1, 2013

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By H. B. Gillis

THE following pages c9ntain a brief description of the processes involved in the manufacture of silica brick at the Sydney plant of the Dominion Steel & Coal Corporation. Silica brick manufacture was commenced at Sydney in 1918, for the purpose of supplying the requirements of the steel plant, where about three million silica bricks were used annually. Previous to that date, all silica refractories were brought to Sydney from American sources and were subject to a freight cost of nine dollars per ton, or about twenty-seven dollars per thousand. As a preliminary step to manufacture, a thorough investigation of all possible sources of silica in the vicinity of Sydney was carried on during 1916 and 1917. ?Eighteen separate deposits were examined. Of this number, only four were found suitable for brick making, and the Leitches Creek silica, being the nearest of these four deposits to Sydney, was selected as the raw material for the proposed plant. CRYSTAL MODIFICATIONS OF SILICA A brief review of the silica minerals may serve to indicate why careful investigation of sources of supply is necessary before actual brick-making is attempted. The crystal modifications of silica, i.e., quartz, tridymite, and cristobalite, all possessing alpha and beta phases, play a most important part in determining the suitability or otherwise of the resulting brick. By heat treatment, any one of these forms of silica may be converted to either of the others. The inversion temperatures (after Fenner) in degrees Centigrade are shown on rage 160.

Jan 1, 1938

Flotation of a mineral bearing particle is the result of successful completion of a chain of events, such as, producing particles with sufficient exposure of the valuable mineral on the surface, reagent adsorption, suspension of the particle in the pulp, collision of particle with air bubbles and subsequent attachment, ascending to the froth column and transport to the concentrate stream, among others. These sub-processes in turn are affected by the feed properties such as size and density, and process variables such as size of air bubbles, degree of turbulence in the cell, particle/particle interactions etc.. Thus, inefficiencies occurring in any one or more of the above processes will result in inefficient flotation performance. In spite of its dependency on a wide variety of sub-processes, flotation performance is commonly modelled based on first order kinetics using two or three parameter models. As the model parameters may be affected by several of the sub-processes mentioned above, interpretation of their variations and identifying the specific causes is extremely difficult. Of the many factors that influence the flotation performance, liberation information of the particles such as the grade distribution and surface exposure are considered vitally important. In this paper, it has been demonstrated a) how a predictive liberation model may be derived and used in quantifying the liberation information of the particles produced at various grind sizes and b) how the flotation process may be modelled by explicitly incorporating the liberation information, thereby improving the accuracy of the model. Comparisons of the observed data with the proposed model and those of published liberation/flotation models have also been made.

Jan 1, 2016

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By B. Jakovljevic, M. D. Soderstrom, T. McCallum, A. J. Quilodrán

Cytec has developed a new organophosphorus based solvent extraction (SX) reagent for rare earth separations. The new product, CYANEX® 572, has been formulated to allow efficient extraction while minimizing the strip acid requirements. The optimization of formulation strength is expected to significantly reduce the operating costs of these circuits. Modeling capabilities for CYANEX® 572 (similar to those used successfully in Cu and Co/Ni SX) have also been developed to aid in the design and optimization of the SX circuits. Simulations will be shown comparing CYANEX® 572 to a traditional rare earth extractant.

Jan 1, 2014

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By Rufus L. Chaney

A new technology is available to the Ni mining and remediation community to “phytomine” Ni from mineralized or contaminated soils using rare plants which hyperaccumulate Ni to over 1% of shoot dry matter. Research has identified useful plant species, and even bred improved cultivars of Alyssum murale and Alyssum corsicum for commercial phytomining in temperate regions. All agronomic practices (fertilization, soil amendments, planting and harvest methods) needed for economic phytomining were identified to attain high yields and high Ni concentration in the biomass. In tropical regions, other species are available such as Phyllanthus which accumulate over 1% Ni in dry shoots. These species are perennial so they regrow after annual cutting to harvest biomass. Expiration of our patents on the technology opens the opportunity for other organizations which control Ni rich natural soils or contaminated soils requiring remediation to commercialize the technologies. Inexpensive methods to remediate/revitalize Ni contaminated phytotoxic soils using agronomic approaches have also been developed and demonstrated at Port Colborne, Ontario, but adoption is delayed until formal agreements with government are completed. These new simple remediation and profitable phytomining technologies can obtain Ni from soils which contain Ni well below levels considered economic for current mining technologies, and the plants biopurify the Ni so it is easy to recover Ni metal from plant ash by pyrometallurgical or hydrometallurgical technologies. Although increasing pH decreases the solubility of Ni in all soils, raising pH increases Ni accumulation by Alyssum species. Hence usual chemical extraction methods for phytoavailable soil metals such as the DTPA- or NH4-OAc-extraction cannot predict Ni accumulation by Alyssum species.

Jan 1, 2016

By Michael K. Watkeys, Jacobus E. Potgieter, E. Guy Charlesworth, Carl R. Anhaeusser, Roger L. Gibson, Alexander F. M. Kisters

Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-erustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress [( )] during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diapir-like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By T. Boiselle, C. Gielen, P. Henry, J. M. Bier

"Hydrometal is specialized in the production of zinc sulphate from complex secondary raw materials. Electric Arc Furnace (EAF) dust is one of the more interesting potential sources to produce zinc sulphate. In order to minimize waste quantities generated from EAF dust treatment, our R&D team has developed and patented a new process to recover the Fe contained in the dust as iron oxide product to be used and sold into the pigment market. The process is based on a specific reductive leaching step of the zinc ferrite contained in EAF dust, followed by a purification step to remove impurities (Ni, Cr, Cu...) and finally the controlled precipitation of the iron oxide. The aim of the iron precipitation step is to obtain the right shape and length of crystals in order to guarantee the right color and tinting strength of the pigment. The innovative aspects of the process results in the controlled oxidation of the iron to get the right crystal size and good purity material. The iron product can be valorized as red or yellow pigment often produced by the Penniman-Zoph process.INTRODUCTION A Few Words about HYDROMETAL Hydrometal SA (Engis, Belgium) is a subsidiary of Jean Goldschmidt International SA (JGI) in Brussels. JGI is mainly involved in metal trading activities (Goldschmidt, 1995). In 1985, JGI acquired the leaching circuit of a Belgian electrolytic zinc producer located in Engis, a few kilometers south of Liège, near the river Meuse and it was decided to name this plant: SA HYDROMETAL. Hydrometal is well connected by water, rail and road from its central location in the industrial region of Liege, in the heart of Europe. The company received in 1997 an additional license to process and recycle toxic and hazardous waste. Figure 1 shows a picture of the plant."

Jan 1, 2016

By R. Marleau, R. Assad, J. Dugas

"A study of the geological features of known occurrences of mineralization in Gaspe is the basis for a classification. Nickel, chromite, asbestos and some copper are pre-or syn-Taconic, whereas the most important deposits are tied to granitic post-Taconic stocks. Most occurrences are clearly related to igneous rocks: nickel, chromium and asbestos to Ordovician serpentinite; copper to volcanic rocks of different ages; and copper, zinc and lead to acidic intrusions with apparent zoning. Some lead-zinc deposits lying between the Grande Greve and York Lake formations are stratigraphically controlled. Some occurrences are tied to faults; e.g., the nickel-copper mineralization along the North Grand Pabos fault. Northerly-trending transverse structures appear to coincide with the Gaspe Copper, Mount McGerrigle (Tabletop) granite and Lemieux dome areas of mineralization. JEAN DUGAS, after graduating"

Jan 1, 1969