Search Documents

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By Oy Leuangthong

The McMurray formation in the Athabasca oil sands deposits of Northern Alberta is part of the world?s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modeling of the McMurray formation using modern geostatistical techniques. Geostatistical modeling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: (1) assessing the most appropriate stratigraphic transformation for optimisation of the correlation structure, (2) determining representative distributions with declustering and debiasing techniques, (3) modeling spatial continuity of the bitumen grade, fines grade, water saturation and other petrophysical variables, (4) performing estimation and cross validation as checks against simulation results, (5) performing simulation for uncertainty quantification of bitumen and fines grade, and (6) model checking of simulation results against the input data and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed.

May 1, 2004

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By Alain Langlais, Caroline Boudrias Chapleau, Claude Bazin, Ahmed Bouajila

"Slurry «viscosity» has been recognised for several decades as a variable that significantly influences the operation of grinding mills. This paper describes an instrument that can be used in a laboratory or a plant to measure and monitor the flow properties of mineral slurries. Laboratory results obtained for two different ore samples are consistent with results obtained during a full scale trial. The results provide a basis for analysing the effect of the solids concentration and particle size distribution on the slurry flow properties. Grinding tests were also conducted in an attempt to link the grinding efficiency to the rheological properties of mineral slurries.INTRODUCTIONThe flow properties, or incorrectly called «viscosity», of a slurry influence the operation of mineral processing devices. Work has been conducted for instance to assess the effect of this variable on the operation of hydrocyclones (Kawatra et al. 1996; Klimpel, 1982a) and dense media separators for coal (Napier-Munn, 1996). However, most of the research effort has been oriented toward the grinding processes which is still the most energy demanding operation for ore dressing (Fuerstenau et al., 1995).Results of investigations of the influence of slurry flow properties upon grinding performances are presented regularly in the literature since 1950. In the 70's, most of the research work was conducted with the aim of using slurry flow properties for the control of grinding mill and to analyze the effect of that variable upon the population balance model breakage and rate functions (Austin et al., 1984; Hemmings et Boyes, 1977). In the 80's, most of the litterature dealing with slurry rheology was devoted to the use of viscosity modifiers to adjust the slurry flow properties, allowing an increase of grinding mill throughputs (Klimpel, 1982b; Fuerstenau et al., 1985). Although laboratory and pilot plant results show the benefits of adding these modifiers to the slurry, few plants have published results concerning the advantages of such addition (Fuerstenau et al., 1985). It is felt that the use of these modifiers introduce operating difficulties with the concentration circuits, especially flotation (Kawatra et Eisele, 1988)."

Jan 1, 2003

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

In this study, the dissolution behavior of copper and arsenic from five different copper concentrates containing 21-34.7 %wt. of Cu, 1.3-7.3 %wt. of As and 15.6-27.5 %wt. of Fe were investigated under high pressure oxidative leaching conditions. Leaching experiments were conducted using different leaching reagents such as ferric sulfate, sodium chloride, deionized water, sulfuric acid and ferric sulfate-sodium chloride mixture in order to compare the effectiveness of each on the dissolution of copper and arsenic from copper concentrates. The effects of ferric sulfate (0.1-1 mol/L), sodium chloride (0.1-0.5 mol/L) and leaching temperature (100-180C) were investigated under 1 MPa autoclave pressure , particle size >45 m, pulp density of 100 g/L, stirring speed of 750 rpm and leaching time of 60 min. Results showed that the most effective leaching reagents for the dissolution of copper are 0.34 M NaCl and a mixture of 0.1 M Fe2(SO4)3 - 0.34 M NaCl, in which As extraction did not exceed 7%. The copper concentration in the pregnant leach solution obtained after leaching using 0.1 M Fe2(SO4)3 - 0.34 M NaCl was 13-30 g/L, while the concentration of As and Fe were in a range between 0.3-1 g/L and 0.2-10 g/L at 160C. INTRODUCTION Copper sulfide minerals, such as chalcopyrite (CuFeS2), chalcocite (Cu2S) and covellite (CuS) are used for the production of copper in mining and metallurgical industries worldwide. The conventional pyrometallurgical processing followed by electrorefining is a common process for the production of high purity copper (Moskalyk, & Alfantazi, 2003; Padilla, Aracena, & Ruiz, 2012). However, the degradation of copper content and an increase in the amount of metal impurities, especially arsenic (As), antimony (Sb) and bismuth (Bi) in copper concentrates cause serious problems to the production of copper and environmental pollution (Basha, Selvi, Ramasamy, & Chellammal, 2008; Long, Peng, & Bradshaw, 2012). Hydrometallurgical processes are used to recover metals from refractory ores, concentrates and tailings by leaching (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018). During the last decades, hydrometallurgical processing for the recovery of copper from enargite-bearing copper ores and concentrates has been extensively investigated due to its relatively more environmentally benign and less capital costs than the conventional pyrometallurgical processes (Long, Peng, & Bradshaw, 2012; Masloboev, Seleznev, Svetlov, & Makarov, 2018; Choubey, Lee, Kim, & Kim 2018). However, several issues facing the hydrometallurgical processing are incomplete extraction of copper associated with the coprecipitation of iron compounds, difficult stabilization of toxic impurities and production of a contaminated copper product (Dreisinger, 2003; Safarzadeh, Moats, & Miller, 2014). Hence, a number of studies have been conducted on the selective dissolution of copper from copper ores and concentrates or selective removal of arsenic leaving a clean copper residue using various leaching reagents or lixiviants (Safarzadeh, Moats, & Miller, 2014; Mihajlovic, Strbac, Zivkovic, Kovacevic, & Stehernic, 2007; Tongamp, Takasaki, & Shibayama, 2009). More extensive studies on the selective extraction of copper from enargite- bearing copper ores and concentrates are much needed to improve copper recovery.

Jan 1, 2019

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

By J. E. Quinn, S. Wolstencrof, K. H. Soldenhoff

Ion Exchange (IX) using Strong Base Anion Exchange (SBA) resins is conventionally used to purify uranium from sulfuric acid pregnant leach solutions (PLS), particularly when uranium grades are relatively low. However, the presence of chloride in the PLS interferes negatively with conventional SBA based IX processes, by reducing the uranium loading on the resin. Chloride can be present in the PLS due to the use of saline bore or seawater in leaching, or chloride containing leach/IX reagents. ANSTO has been examining strategies to combat this problem for several years. ANSTO previously reported that a recently developed high-capacity SBA resin was capable of extracting uranium efficiently from saline leach liquors produced at Boss Resources’ Honeymoon in-situ recovery mine in South Australia. The resin was tested successfully in a 2017 Field Leach Trial carried out onsite in the existing wellfield area. While the piloting was extremely promising, the elution was more challenging, with eluate tenors limited to 2 g/L U3O8 using NaCl. This is due to the resin’s strong affinity for the uranium complex, which makes it difficult to elute efficiently by standard methods. In this paper, we describe a novel elution process developed for strong base resins that significantly improves upon conventional methods. The process, developed by ANSTO, is based upon conversion of the extracted uranyl sulfate species to uranyl carbonate, followed by elution with sodium chloride. The loading and elution process was demonstrated in continuous locked-cycle piloting conducted at ANSTO in 2019. The results were excellent, with eluate tenors of 8–9 g/L U3O8 achieved from Honeymoon PLS containing 50 mg/L U3O8, with very little transfer of impurities. In subsequent test work, the eluate was shown to be amenable to uranium peroxide precipitation. The results represent a huge step forward for the purification of uranium from saline leach liquors.

Jan 1, 2020

By A. A. Beland, R. J. Dawson, S. Shewchuk

"Shovel buckets, scraper blades, dipper teeth, mine car wheels and hammermills are examples of equipment which require routine maintenance due to abrasion. Service life can be extended by the use 0/hard/acing and buildup materials. Mining and milling applications are described and field welding procedures discussed.A high-stress abrasion test used to select hard/acing and buildup materials/or hammers in a hammermill is described in detail. Field tests of the selected alloys confirmed their performance, and maintenance records showed a significant saving in down time and cost.The relationship between the abrasion resistance of the alloys and their hardness, work hardening, composition and microstructure is summarized. IntroductionLarge volumes of ore are handled daily by the mining industry. The abrasive nature of most ores results in extensive wear to both handling and processing equipment. If such wear is neglected it may cause lost production time and also, in extreme cases, require the complete replacement of expensive equipment. The well-planned maintenance of components subject to abrasive wear by means of buildup materials and hard facing can result in substantial economic benefits. Such benefits can , however, only be realized through the correct choice of welding process, consumables and deposition methods available to maintenance personnel. Hardfacing MethodsHardfacing is applied by a variety of methods; the three most widely used being arc welding, oxyfuel gas and thermal spraying. Table 1 summarizes the major processes used within each method. Filler metals in the form of rod, wire or powder are necessary to fulfill the individual requirements of each process. The filler rods are available in the cast form or, in the case of ductile metals or alloys, as wrought rod or tube. All types are supplied bare or flux covered. Wire is supplied in two forms, drawn flux cored and drawn solid. Powder filler metals are available in many metals or alloys; they may be simple mechanical mixtures or prefused and atomized alloys made to a specific size range and shape for optimum results for each applicable process."

Jan 1, 1980

By Adam Powell, Matthew Earlam

INFINIUM, Inc. is scaling up a new molten salt electrolysis process for producing rare earth metals. Instead of conventional carbon anodes, this process uses Pure Oxygen Anodes™ which employ a stabilized zirconia solid electrolyte between the molten salt and anode. This eliminates two problems with today's rare earth metal production technology. First, it eliminates carbon anodes and contamination of the product by carbon and its impurities, enabling 10-100 times larger batch size than current practice, and lower labor costs. Second, it eliminates emissions of perfluorocarbons (PFC) such as CF4 and C2F6, which are very problematic greenhouse gases with 6000+ times the global warming potential of CO2. The zirconia also enables a sealed vessel with no LiF emissions, creates a reducing environment enabling use of low-cost welded steel vessels, and either produces a high-purity oxygen by-product or can use natural gas to reduce the necessary electrical energy with no HF production. This paper will describe the technology and its current status for rare earth metal production.

Jan 1, 2014

By Timothy W. Ellis

Wire Bonding is the dominant IC interconnection process presently used in the semiconductor assembly industry (1). The flexibility, adaptability and cost of wire bonding will continue to keep it as the key process for the interconnection of integrated circuits to substrates. However, wire bonding still has certain technological hurdles to overcome if it is to continue following the semiconductor roadmap (2). Particular issues which need to be addressed include low overall tensile strength, low elastic modulus, low shear per unit area and mechanical loop stability of Gold based micro-alloys. The ability to produce ?Deformation Process Metal-Metal Matrix Composites? (DMMCs) is based upon the deformation nature of immissible metallic systems. For reference, the Gold (Au)-Molybdenum (Mo) phase diagram is shown in Figure 1 (3). By inspection of the diagram, Au has a very low solubility for Mo, while Mo has essentially no solubility for Au. This is the metallurgical analog of oil and water. In the Au-Mo case, this is particularly troublesome when producing precursor ingots of the alloy to be formed into wire products. In Table 1, the melting points and densities are shown for Au and Mo. As shown, the melting point of Mo is significantly higher than Au, and is very close to the boiling point of Au (2856°C). However, Au?s density is higher than that of Mo. As such, conventional casting techniques are not suitable, since solid Mo would float off the surface of an Au melt thus depleting the matrix of its alloy addition. In this work, two-phase composite wires were produced by deformation processing to develop an interconnection wire with elevated tensile strength, modulus and shear to those commonly available in the market (4). This technology has been used previously in the production of high strength electrical conductors particularly for high field pulsed magnets (5).

Oct 1, 2003

By C. Nikolic

A process utilizing ozone for the precipitation of cobalt from nickel sulphate liquors containing ammonium sulphate has been developed. Best results were obtained using nickel carbonate to maintain solution pH at 5.0 to 5.5. Work was performed both in column and stirred-tank reactors. Variables studied included neutralizer type and concentration, NH4+ concentration, temperature, Ni++ and Co++ concentration, per cent O3 in the O2 carrier gas, O3 input rate and agitation. The over-all rate of cobalt rejection increased sharply with increasing agitation and ozone concentration in the gas phase, reflecting relatively slow transfer of ozone from the gas to the liquid phase.

Jan 1, 1978

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By L. W. Hamel

"DUST CONTROL - GRANISLE COPPER LIMITEDINTRODUCTIONGranisle. Copper Limited is located in the north-central region of the Province of British Columbia, approximately 200 road miles north-west of Prince George. Mill startup was in November, 1966, at a rate of 5,000 tons per day, expanded to 13,000 in 1973. The primary crushing rate is 1,200 tons per operating hour, and the secondary 750, and they can be operated jointly or separately.DUST COLLECTION SYSTEMS There are seven dust collection systems ventilating the crushing and grinding complex. The individual pickup points are depicted on Figure 1 -""Crushing Plant Flowsheet"", and Figure 2 - ""Concentrator Flowsheet"", e.g. 1A, 1B, 3C, etc.System No. 1 - Primary Crusher The feed rock box of the Allis-Chalmers superior 42-65 primary crusher is ventilated by 19,000 CFM of air exhausted directly to atmosphere by a Sturtevant 426 M fixed discharge fan.No. Dust Pick Up Point CFM lA Crusher Feed Rock Box 19,000System No. 2 - Primary Crushing and Screening System No. 2 ventilates the primary crushing and screening equipment. A total of 19,000 CFM of air is exhausted by a Sturtevant 426 M fixed discharge fan through a Howden Type S - size 75 cyclone locally modified for wet scrubbing."

Jan 1, 1976

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By J. R. Donald, K. Scholey

"Nickel has been mined and processed from the Sudbury basin for over 100 years. During this period, the process has evolved into what is one of the largest and most complex mining and metallurgical facilities in the world. This paper will describe the geology and mining of the Sudbury basin as well as the Copper Cliff metallurgical flowsheet circa 2005, including:•,Clarabelle Mill,•,The flash smelting furnaces,•,The bulk converters,•,Matte casting, separation, and processing•,The carbonyl refineries•,Carbonyl residue processing•,Copper processing•,Sulphur productsThe challenges of today and the opportunities for the future are discussed."

Jan 1, 2005