Search Documents

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By L. T. Raevskaia

We discuss the stability problem of a piston of the reversible axial-piston pneumatic motor called DAR-14M. We performed the full analysis of stress and deformation characteristics of the piston near a resonant frequency with the help of FEM ANSYS. We estimated the own frequency of the piston analytically for the given motor, this estimate was confirmed numerically in the model analysis FEM ANSYS. It was also shown in harmonic analysis that loaded piston end behaves very different in comparison to the unloaded end. As expected, maximum deformation was found in the area of the holes of the bearing shaft, indicating an optimization necessary in that region of the motor.

Aug 1, 2013

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By S. Kobayashi, N. Ohara, T. Aoki, S. Sakurai, M. Iwano, M. Shimo, I. Otsuka

"This project is the upgrading of a commuter line of approximately 76 km to improve the railway system in Istanbul metropolitan area. Railway tracks have been connected between Asia and Europe through a tunnel under the Bosphorus Strait. The length of these underground structures sums up 13.6 km. In this paper, the observational construction management based on field measurement performed at large scale underground railway station (Sirkeci station) constructed by means of New Austrian Tunneling Method (NATM) is described and the mechanism for generation of ground surface settlement above this station is discussed.Buildings above Sirkeci station are overcrowded. About 60% of the buildings are made of reinforced-concrete (RC) and others are of brick. Based on the investigation into the predicted settlement and inclination, necessary actions such as structural reinforcement and soil improvement have been conducted for dilapidated buildings.Rock mass around Sirkeci station consists of alternative strata of sandstone and mudstone. It is overall soft rock with an elastic modulus of 150 MPa, partly including fractured zones. Overburden is about 30 to 40 m. The thickness of unconsolidated sand layer distributed on the bedrock is about 10 m. As a result of in-situ permeability tests, the coefficient of permeability of the sand layer is about 1.0x10-3 cm/s. Fill layer of about 10 to 25 m in thickness covers the sand layer at the ground surface. The fill layer contains a lot of artificial waste like splinters of wood, brick chips and mortar chips, etc. in addition to gravel, sand, silt and shells. The coefficient of permeability of fill layer is estimated to be 1.0 x10-2 cm/s, which is one-order greater than that of the sand layer. Fill layer consists of ancient city ruins of ages respectively from the Eastern Roman Empire, the Byzantine Empire and the Ottoman Empire and has a lot of gaps.The underground part of the Sirkeci station was excavated through a ventilation shaft. Ground surface settlement occurred more than predicted. Therefore, back analyses were performed in order to precisely predict the next-step settlement. However, back analyses with elasto-plastic models could not simulate the actual phenomena and hence, an anisotropic-damage-parameter model developed by Sakurai (1999) was adopted for the back analysis. Furthermore, as the excavation of tunnel proceeded, the ground surface settlement exceeded the predicted value again. Based on the monitoring results, it seemed that pore water pressure decreased by the tunnel excavation resulted in the soft rock and soil to be contracted due to the increase in the effective confining pressure. A coupled hydraulic-mechanical analysis was applied to explain the relationship between decreased pore water pressure and ground surface settlement. The settlement due to drainage from tunnel wall was well-estimated in the coupled hydraulic-mechanical analysis.However, further settlement occurred more than predicted again and again. Though it was very difficult to clarify the reason of the large settlement, it was recognized that the unexpected ground surface settlement resulted from the existence of the large gaps in the fill layer that was greatly compressed. The final settlement reached up to 327 mm."

Jan 1, 2015

By S. Sagar

In September 1996, Dofasco commissioned a 165 Mt twin shell EAF furnace and an associated ladle fleet. During and after this startup, refractory performance in the ladles was optimized on a holistic approach through several initiatives that increased ladle refractory retention times from 7000 to over 16000 mins (160 heats). This dropped the overall refractory costs by 40% while ensuring a consistent and predictable ladle performance. One initiative that drove enhancements was the proper brick selection for each particular refractory area and it's process conditions. The work concentrated on the selection of a resin bonded alumina magnesia carbon (AMC) brick in the barrel area of the ladle, upgrades to the 2 piece monolithic alumina cast ladle bottom and increasing the slagline refractory brick quality with the appropriate zoning/paneling. The adoption of a magnesia alumina carbon (MAC) brick in the transition area of the barrel/slagline has also improved performance and predictability. The design developments have lowered the overall wear rates and balanced the service life of the entire ladle. Safety was improved and breakout potential reduced by changing the safety lining from a high alumina brick to a state of art technology - monolithic shotcrete lining. This initiative decreased the overall manpower required to brick a ladle and increased shop ladle availability. The ladle bricking area environment was also improved by adopting a post combustion device to burn phenol fumes from ladle preheating practices. This has improved the overall health & safety of the reline teams. The consistent and predictable performance of the ladle on a whole has allowed the shop to decrease the number of working ladles in operation from 5 to 4. This further decreased wear rates from over-oxidation and excessive thermal cycling, saving approximately $500,000 in natural gas from pre-heater operations.

Jan 1, 2004

By W. R. Bacon

"MAGNETITE HAS BEEN found in many .parts of the coastal area of British Columbia, but the more important deposits are on Vancouver Island and Texada Island. The locations of these deposits are shown on Figure 1.Interest in the magnetite deposits dates back to the 1870s, when land was acquired on the southwest coast of Texada Island by the Puget Sound Iron Company. This ground included the Prescott, Paxton, and Lake deposits. During the years 1885 to 1903, and 1908, 28,898 tons of magnetite ore was shipped to the company's blast-furnace plant at Irondale, Washington, U.S.A. This production was almost entirely from the Prescott open-pits.In the years following the Texada Island discoveries, other magnetite deposits were found in the coastal area, and various plans were proposed to utilize the local ores in the establishment of a steel industry in the Pacific Northwest. None was carried to fruition but, in 1951, open-pit mining was begun at Iron Hill, Vancouver Island, to furnish iron concentrates for steel mills in Japan. In 1952 mining of the Texada deposits was resumed to supply the same market. Production figures for these recent operations are as follows:"

Jan 1, 1949

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

By Z. Gostynski

The paper is a historical cross-section through a 28-year period of operation of the direct-to-blister Flash Smelting Furnace in the KGHM Glogów Copper Plant. It presents the origin of the furnace as well as the path of numerous changes and modifications both in technology and process introduced in the furnace in response to the production and cost-reduction challenges. The authors provide justification of the statement that continuous improvement of the "Polish" Flash Smelting Furnace has ranked it among the most modem smelting units in the world.

Jan 1, 2007

By Z. Q. Yue

Many large rock avalanches and/or landslides have occurred in mountainous regions around the world. Their occurrences are normally rapid and unexpected, which can cause disasters. They have been investigated extensively by many researchers and engineers since the 1903 Frank Slide on Turtle Mountain, Alberta, Canada. They are one of the most peculiar phenomena because the rock debris of more than one million m3 can move over the horizontal distances exceeding those expected from conventional friction physics. This paper presents a gas cause hypothesis responsible for the large rock avalanches. It is the migration and expansion of a certain amount of highly pressurized and dense natural gas mass from deep geological grounds into the mountainous rock mass slopes. The natural gas with high pressure and density can escape from the deep geological ground and flow through faults, weak zones and/or porous channels into the rock mass forming a mountainous slope. The rock mass forming the slope has the high tensile and compressive strength and can resist the initial loading of the gas mass migrated into and stored in their voids, pores, holes, gaps, openings, apertures and cavities. With time, more and more gas mass from deep ground can migrate into and stored in the slope rock mass. Eventually, the peak equilibrium of forces and deformation reaches. The expanding power of the gas in the slope rock mass would instantly and rapidly break, erupt and/or explode them. The compressed and dense gas mass would mix, flow and expand together with the broken rock debris mass and continue offering their remaining expanding powers to the moving and sliding debris mass. As a result, the rock debris of large volume can reach the runout distances exceeding those expected from the conventional friction physics. The gas would escape into the sky and the solid rock debris would remain on the ground spreading over large ground area. The 1903 Frank Slide is examined to show this gas cause and mechanism in mountainous regions.

Jan 1, 2015

By N. Maleki

Magnesium matrix composites are widely used in automotive and aerospace industries for achieving higher performance due to their light weight. The Mg2Si intermetallics compound in Mg/Mg2Si composite exhibits many excellent properties such as high melting temperature, high hardness, and low thermal expansion coefficient. However, under normal cast conditions, the primary Mg2Si phase exhibits coarse Chinese script or dendritic morphologies and the eutectic structures is very brittle resulting in the low ductility and strength of the alloys. Modification treatment is a very effective method to obtain fine microstructure and improve the mechanical properties of the alloys due to low production cost. In this investigation various amount of bismuth addition have been carried out on Mg?5wt %Si alloy to refine and modify the morphology of coarse Mg2Si in order to improve the corrosion resistance of the composite product. The effect of Bi content on microstructure of Mg2Si/Mg composite was investigated by optical and scanning electron microscopy followed by EDX analysis and X-Ray diffraction. In order to compare corrosion resistance of unmodified and modified specimens, Immersion test and potentiodynamic polarization (PD) were used. The results showed that by Bi addition, the size of primary phase Mg2Si was considerably reduced and the morphology was modified from a coarse dendritic shape to a polyhedral shape. The results also indicated that the corrosion resistance of Mg?Si alloys was improved by the addition of 1%wt of Bi due to the reduction, refinement and evenly distribution of Mg2Si phase. Indeed, both the morphology and distribution of Mg2Si intermetallic had a great influence on the corrosion behavior of Mg/Mg2Si composite.

Oct 1, 2011

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

"These guidelines have been prepared to assist the Qualified Person(s)in the planning and supervision of exploration programs which will be reported under National Instrument 43101. The Companion Policy of NI43101 references the guidelines and states that issuers and Qualified Persons should follow them.Exploration Best Practices GuidelinesPreamble: These guidelines have been prepared to assist the Qualified Person(s) in the planning and supervision of exploration programs which will be reported under National Instrument 43-101. Such exploration programs must be under the supervision of the Qualified Person who will be responsible and accountable for the planning, execution and interpretation of all exploration activity as well as the implementation of quality assurance programs and reporting. These guidelines are also recommended for use in the planning and execution of exploration programs which will not be reported under NI 43-101. This set of broad guidelines or ""best practices"" has been drawn up to ensure a consistently high quality of work that will maintain public confidence and assist securities regulators. The guidelines are not intended to inhibit the original thinking or application of new approaches, that are fundamental to successful mineral exploration.Results should be summarized and reported in a Technical Report of good professional quality in accordance with the National Instrument 43-101 and Form 1 contained in that instrument. All exploration work from which public reporting will ensue must be designed and carried out under the supervision of a Qualified Person (""QP""). A QP is defined in National Instrument 43-101 as an individual who is an engineer or geoscientist with at least five (5) years' experience in mineral exploration, mine development, mine operation or project assessment, has experience relevant to the subject matter of the project or report and is a member in good standing of a recognized professional association."

Jan 1, 2003

By E. A. Haack, L. A. Warren

Microbial biofilms are essentially biologically driven, geochemically reactive interfaces between solid surfaces and aqueous solution. Field investigation of acid rock drainage (ARD) associated biofilms at the Onaping nickel mine (Onaping, ON, Falconbridge Ltd.) characterizing: (1) micro-geochemical gradients (pH and 02) (2) metal fractionation amongst biofilm solid components, and (3) microbial communities; over both seasonal and diel timescales, indicates biofilms are highly metal reactive. Results show that biofilms accumulate metals seasonally within two microbially controlled solid fractions: amorphous hydrous manganese oxide (HMO) biominerals and the organic biofilm matrix. The biofilm geochemical microenvironment, driven largely by microbial activity, dynamically impacts biofilm metal behaviour over diel timescales. These results indicate that microbes can play significant roles in bulk system reactive metal transport. On-going investigation seeks to characterize the microbial players and the microbial-geochemical linkages involved in Mn oxyhydroxide formation and subsequent metal sequestration, with the goal of engineering this microbial activity as a bioremediative approach. This approach will have utility beyond specific application to the Falconbridge Onaping site to ARD mine environments in general, as the likely microbes involved in these processes are typically common across ARD systems.

Jan 1, 2004

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By A. J. Antony Chettupuzha

Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project as well as model project processes. Much of the information relating to processes and their structure, the actors that operate them, and the data associated with each instance of a process is encapsulated within workflows. The wealth of information contained in an EPPM system can be exploited to extract knowledge that can provide significant cost benefits to construction companies. Workflows provide an ideal medium for the capture of knowledge over the course of a project lifecycle. We demonstrate how this knowledge may then be used to analyze workflows and determine metrics that establish the suitability of workflows to construction processes. We present a conceptual approach to measure the performance of a workflow, its constituent components and evolution, which may be used to lay the foundation for establishing paragon workflows suited to classes of construction activities.

Aug 1, 2013

By Steve R. McCutcheon, Cees R. Van Staal, John P. Langton, Leslie R. Fyffe

The volcanic-dominated Tetagouche Group in northern New Brunswick contains numerous massive-sulfide deposits and intimately associated metalliferous sediments. The massive sulfides are generally hosted by Llanvirnian-Llandeilian volcaniclastic sedimentary rocks of the Nepisiguit Falls, Patrick Brook, and Boucher Brook formations. These formations are intercalated or closely associated with rhyolitic-dacitic flows and/or domes, and minor continental tholeiites of the Flat Landing Brook Formation. Pyroclastic rocks are relatively scarce in the silicic volcanic complex. Tuffites and epiclastic sandstones, of the Nepisiguit Falls and Patrick Brook formations, respectively, generally occur along the fringes of the silicic volcanic complex. The flows and tuffites are intruded by quartz- and feldspar-phyric rhyolite (porphyry) dykes, sills, and domes. Although the volume of the silicic volcanic complex is large, evidence for a previously proposed collapsed-caldera model is lacking. On the basis of host-rock type and stratigraphic position, the sediment-hosted massive sulfides have been divided into three groups: the Brunswick-, Caribou- and Halfmile Lake-type deposits. Syngenetic feeder pipes and asociated alteration zones are generally not present beneath the Caribou- and the Halfmile Lake-type deposits and, if present at all, are poorly developed underneath the Brunswick-type.

Jan 1, 1992

By X. Xu, J. K. -W. Wong, J. -Y. Delenne, K. Soga

Hydraulic fracturing (HF) is a mulit-scale and multi-physics process which makes numerical modelling challenging. Conventional numerical models focus on multi-physics nature of HF but the multiscale nature is compromised by idealization of reservoir to be continuous, homogeneous and isotropic. However, natural fractures take a significant role in the success of HF for exploration of unconventional resources like Shale gas. Advancement in microseismic monitoring provides useful data for simulation in a much greater details. There is an urgent need to develop a suitable numerical tool for multi-scale threedimensional simulation to better understand the roles of discontinuities and heterogeneity in reservoir and its interaction with HF, especially to address the environmental concerns such as induced seismicity. In this paper, a simple discontinuum numerical method – Lattice Element Method (LEM) is proposed to model HF in a large scale three-dimensional model. A reservoir is modelled as a lattice network composed of 1D Hookean’s spring. Fracturing is modelled simply by removing lattices that meet a specified threshold as determined by the critical energy release rate of the rock. By introducing disorder in the model, mesh dependency in modelling fracture growth is minimized. Fluid flow is simplified as flow in pipe network and the permeability of pipe is related to fracture aperture by cubic flow law. Therefore, fracture flow and rock deformation are fully coupled. In this paper, four simulations of the same configuration except with different degrees of reservoir heterogeneity are presented. Fractures formed are diffusive and two groups of fracture are identified – connected fractures and isolated fracture without clear spatial correlation. The former forms a ‘fracture cloud’ and contributes to fluid flow and modeled by pipe network. The flow of fluid is highly tortuous and pipe network is sparely connected. The degree of reservoir heterogeneity controls the growth of ‘fracture cloud’ and pipe network. Microseismic monitoring often shows diffusive fracturing during HF on site and hence the outcome of the proposed model can be compared to such monitoring results.

Jan 1, 2015

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013

By T. Schmidt, H. Assadi, F. Gartner, H. Kreye

Among all spraying processes, cold spraying has attracted a special attention in recent years, both as a coating - and more recently - as a rapid manufacturing technique. The interest in this process is mainly because of the fact that the deposition of spray material takes place at moderately low temperatures, and thus, oxidation and unfavourable microstructural changes can be alleviated. In this process, a highly compressed gas, flowing through a de Laval nozzle, accelerates the particles of the spray powder to high velocities of up to 1200 m/s. Although there is no melting of particles prior to impact on the substrate, cold-sprayed deposits can be denser and more tightly bonded as compared to the equivalent deposits produced by conventional thermal spraying methods. The present contribution focuses on this unique aspect of cold spraying. Modelling of particle impact, combined with various experimental observations, is employed to illustrate that bonding of particles and hence material deposition occurs through shear instability - associated with severe plastic deformation and localized heat generation - at the interacting surfaces of particles and substrate. The results of modelling also provide an insight to the influence of material and process parameters on the critical velocity and on the microstructural properties of cold-sprayed deposits.

Jan 1, 2006