Search Documents

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By Sang-Kyun Woo

The electric power conduit (EPC) in Korea has been constructed since 1978. Facing the challenge of safety and sustainability of the EPC, it is urgent to develop an inspection strategy and maintenance system for the structure based on the concept of life-cycle management. This paper introduces the newly developed mobile inspection and diagnostic system of the EPC. The novel aspect of this particular system is the integration of non-destructive mobile inspection techniques with BIM (Building Information Modeling) and LBS (Location-Based Service). BIM is an ideal tool and platform for developing an inspection and diagnostic system, and RFID (Radio Frequency Identification) is a useful tool to construct USN (Ubiquitous Sensor Network) for LBS. The goal of this research is to establish an EPC inspection and diagnostic system concept based on BIM and LBS using RFID. In this research, a BIM model of OPENTBM tunnel for EPC will be established to show the integration of 3D CAD with the inspection data. An EPC?s maintenance database, which includes the deterioration types of the structure, inspection records, and repair methods, was designed to interact with the BIM. The system will be implemented by the BIM with the related database, in which the construction geometry and all related information are stored. The proposed system was designed to utilize the inspection and diagnostic system under the USN environment using RFID in EPC directly.

Aug 1, 2013

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009

By N. B. Clarke

LIMESTONE, as a name, covers a great variety of stone consisting of varying amounts of calcium carbonate, magnesium carbonate, and impurities such as silica, alumina, and sulphate of lime. In the iron and steel industry, limestone is roughly divided into two classes, namely Calcite, when the magnesium carbonate content is below 10 per cent, and Dolomite, when the magnesium carbonate is over 10 per cent. In practically all metallurgical melting, the quality of the finished product is related to the character of the slag, and limestone is used as a flux to achieve the proper analysis and consistency. The function of the slag is to absorb the undesired elements of the bath and also to act as a protective cover over the metal. The carbonates of calcium and magnesium are the effective agents in fluxing, and the silica, alumina, sulphur, and other foreign matter are objectionable impurities which should be as low as possible, totalling not over S per cent and preferably below 3 per cent, since all of these so-called impurities must be fluxed by the lime and magnesia of the stone. When the lime and magnesia of the stone have to be used to flux its own impurities, there is that much less of these two oxides left for fluxing the impurities from the balance of the charge, and, as a result, more lime-stone must be used than is desirable with good practice.

Jan 1, 1939

By G. R. MANSON

The Brisco Barite Mine lies 70 km south-southeast of Golden, British Columbia. Barile mineralization occurs in a northstriking brecciation zone within Ordovician-Silurian Beaver/ oot dolomites and quartzites. Brecciation was caused by faulting related to the Mount Forster-Steamboat Fault. The main barite vein occupies a fault zone and is up to 12 m wide and over 250 m long. It is light grey to white, fine grained and compact; BaSO4 content is 9/. 70 per cent. Production started in 1945 and has continued to the present. Barile originally was removed from an open pit; later, an adit, begun in 1957, reached more than 240 m along the vein, 15 m below the pit floor. Today ore is hoisted from a decline resting some 37 m below the pit floor.

Jan 1, 1984

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

The article presents an outline of methods and certain results of laboratory tests, underground tests and model tests, aimed at assessing performance of a powered shield support on the floor of low strength parameters. The tests were conducted within the framework of GEOSOFT project co financed by Research Fund for Coal and Steel (RFCR-CT-2010-00001). The described research works were conducted by Central Mining Institute (Glówny Instytut Górnictwa), Janina coal mine and Becker-Warkop

Aug 1, 2013

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By Clifford R. Stanley

"Abstract - Reproducible analyses of representative samples for elements affected by the ‘nugget effect’ is vital in mineral exploration and reserve estimation. Unfortunately, a priori knowledge of what size of sample is representative from a mineral deposit or its dispersion train is commonly unavailable. Use of the simple ‘equant grain model’ and the NUGGET computer program facilitates determination of the sampling parameters that will produce appropriate samples for chemical analysis. Based on Poisson statistics, NUGGET can be used to determine: (1) the ‘effective grain size’ of nuggets in a suite of samples, (2) the level of representativity (precision) that samples with specific nugget grain sizes will exhibit, and (3) the sample size required to obtain a specific level of sample representativity. The program determines these sampling parameters for any element in any mineral, including solid solution minerals (e.g., Au, electrum, Pt-Fe alloy, diamond), and allows assumption of a variety of grain shapes (e.g., ellipsoids, cylinders, parallelepipeds, etc.). Furthermore, it outputs the effective number of nuggets expected in a sample of given size and the percentile confidence bounds on any element concentration affected by the nugget effect.Results from the software allow determination of effective sampling and analysis strategies that minimize the nugget effect in geochemical analysis/assaying used in mineral exploration and reserve estimation. This will not only improve confidence in the resulting exploration results or reserve estimate, but will facilitate estimation of the error associated with any subsequent interpretation or reserve figure."

Jan 1, 1998

By Jean-Guy L. Gauthier

"With the Ontario Ministry of the Environment stipulating that the cumulative concentration of copper, lead, zinc and nickel in mine mill effluent must be no greater than 1.0 milligram per litre, it has become necessary for the mining industry of find some form of treatment for the removal of heavy metals from effluent waters.To comply with these guidelines, it became necessary for Mattabi Mines Ltd., which is situated 50 miles Northeast of Ignace in Northwestern Ontario, to develop a compact, cost effective and technically sound treatment process to remove heavy metals from their tailings overflow. A design committee consisting of mine metallurgists, environmental engineers, a Dutch research and development team and the equipment supplier engineering staff was set up to accomplish this.Using some new and innovative wastewater treatment equipment, the guidelines established by the Ontario Ministry of the Environment can now be met. The sludge produced from the precipitated heavy metals is sent directly to the concentrator, thus eliminating the danger of re-dissolution of the metals in a landfill site, while recovering some of the valuable metals that would otherwise be wasted in a sludge landfill."

Jan 1, 1980

Diverse and considerable energies are associated with mobile equipment operated and maintained on mine sites. Loss of control of these energies is a common cause of injury on mine sites and this is well recognised by the mining industry. In 2006, 4 multi-national mining companies formed the Earth Moving Equipment Safety Round Table (EMERST), with the aim of engaging collectively with the manufacturers of equipment to accelerate improvements in mining equipment design. Originally focused on surface mining equipment, and particularly haul trucks, the focus of EMESRT widened to include underground and exploration equipment. Since 2006, EMESRT has maintained a program of regular visits and other engagements with a steadily increasing number of manufacturers. The membership of EMESRT has also increased, with 15 companies being members in 2012. An initial step undertaken by the EMESRT members was the development of ?Design Philosophies? which drew of the collective experience of mining companies to identify potential unwanted events which cause equipment related injuries and illness. A technique for analysing risks associated with operation and maintenance tasks, the Operability and Maintainability Analysis Technique (OMAT), was subsequently developed and trialled. In 2011, the EMERST members resolved to propose a common form of safe design information to be requested by all members companies during procurement, and the resulting EMERST Design Evaluation for Equipment Procurement (EDEEP) process was launched at MINExpo in Las Vegas in September 2012. The outcomes of OMAT risk assessment and control activities are integrated during this process into a common ?Safe Design Information? template for communication to prospective purchasers. The aims of requesting manufacturers to follow this process are to provide equipment purchasers with a common way of assessing how well the issues in the EMESRT Design Philosophies are addressed in the equipment design; and to provide manufacturers with additional information for use during equipment design. The process involves identifying priority tasks based on frequency and the severity of the consequences of potential unwanted events identified in the EMESRT Design Philosophies; undertaking a task-based risk assessment of priority tasks in conjunction with site-based personnel; evaluating the effectiveness of control measures; and providing information about safe design features in a standardised format.

Aug 1, 2013

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By W. L. Uglow

In recent years, the microscope has come to be recognized as a valuable aid to engineers whose business is the discovery, development, concentration or reduction of metallic ores. In many of the large treatment plants microscopical research has already an important status; and in the hands of efficient operators the microscope has indicated methods of solving ore problems resulting in the saving of thousands of dollars that otherwise might have been lost in tailings, or expended in freight rates or smelter charges. Failure to procure all the information that the microscope can supply concerning the physical and mineralogical characteristics of complex ores has in many cases led to the construction of unsuitable concentrators, just as the failure to investigate in detail the geological conditions of an ore deposit has often results in the squandering of money on shaft sinking, and mechanical installations which subsequent development of the deposit failed to justify. The great progress recently made in the selective separation of minerals by means of the various processes of flotation and leaching brings strongly to our attention, the scope of the field in which microscopical methods may be advantageously employed. The microscope enables one to observe the minute details of rock, ore, gangue, concentrate, tailing, matte, slag and metal, that are invisible to the naked eye. Furthermore, the technique of microscopal research has been so highly developed that a microscopist can not only observe, but deter-mine the compositions and measure the diameters of the mineral constituents in the ore to be treated. Magnifications of these constituents up to 3,000 diameters may be produced by the proper combination of eyepiece, objective, and projection apparatus, and the images thus viewed may be photographed through the microscope, and permanent records made of them.

Jan 1, 1924

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006