Search Documents

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By Y. Duna

The reliability of mine ventilation systems is critical to normal and safe production in a mine and includes reliability of the following parts: ventilation system branch (or passage), ventilation structures, ventilation network, and the fan. Among these, the reliability of a ventilation branch may be considered the foundation of the whole ventilation system. The branch ventilation flow includes four parameters: air volume; toxic and hazardous gas concentrations; temperature, and dust concentration. The calculation model for the reliability of a branch was established based on the analysis of normal distribution of flows in any one branch. Then, the efficiency of the ventilation structures and fire risk compromising the reliability of branch was studied. The results obtained were as follows: if the air volume, toxic and hazardous gas concentrations, temperature and coal dust concentrations of the branch are within reasonable limits, set at any stable state and at the same time, then this branch is reliable.

Aug 1, 2013

By Tai Sik Lee

Why ISRU into Space Exploration are important NASA and International Mission statements calls for the sustainable human exploration of the Moon, Near-Earth asteroids, and Mars Common Exploration Goals and Objectives are Strongly influenced by ISRU Extend Human Presence: Continually increase the duration and level of self sufficiency at all destinations Develop Exploration Technologies and Capabilities: Develop and validate tools, technologies, and systems that extract, process, and utilize resource to enable exploration missions Perform Science to Support Human Exploration: Characterize available resources at destinations Stimulate Economic Expansion: Encourage commercial services and create new markets, including markets for discovered resources Enhance Earth Safety: Test techniques to mitigate the risk of asteroid collisions with Earth

May 1, 2013

By Neil Westoll

Extensive Global Network ?Working together, AECOM provides clients with a unique blend of global reach, local knowledge, innovation and technical excellence. ?43,000+ team members worldwide ?450+ offices ?100+ countries ?6 continents The Changing Climate ?Climate change is ?official??IPCC 2007 ?Climate change will create instability, change and opportunities ?Companies that are resilient and adapt will survive and evolve ?CO2/GHG emissions will be curbed by legislation ?How will this affect the mining industry? ?How can the mining industry adapt to the new realities?

May 1, 2009

By H. M. Roscoe

Fifty per cent. increased lump coal production and at the same time a reduction of from 20 to 40 per cent. in explosive consumption. These results were achieved by the use of the rock-dust cartridge method of stemming shots in the Ruhr coal mines, as announced by Dr. Alfred Stettbacher in the September 1923 number of the Explosive Engineer. Immediately, the explosive and the coal-mining industries on this continent became intensely interested. Considerable experimental work has been carried on in a number of American and Canadian mines during the past year, by which our engineers have become assured that the use of rock-dust cart-ridges for stemming shots increases the efficiency of explosives and promotes safety in coal mines.

Jan 1, 1924

By J. B. De Hart

In the September issue of the Bulletin, 1923, there is a paper by J. A. H. Church on "The Spontaneous Combustion of Coal in Mines", which is more or less a general discussion of the subject. Mr. Church gives a list of mine fires which have occurred in Alberta. Of the total of thirteen fires, six are attributed to spontaneous combustion. Of these six fires, it will be noted that five are in thick pitching seams. These fires occurred in the following mines during the years shown, at Frank in 1909; at Lovett in 1916; at Cadomin in 1920; at Yellowhead in 1922, and at Cadomin in 1923. Every one of these fires has occurred, as Mr. Church points out, in a seam of over 12 feet in thickness, and furthermore not one of these fires has been extinguished, although in every case large sums of money were expended and considerable risks . taken in fire fighting. Now it is quite evident from these facts that mines working seams of this nature are faced with a very grave danger and it behooves us to study the matter and endeavor to arrive at some practical method of preventing the loss of our coal mines from this cause.

Jan 1, 1924

By Alan S. Lock

Large scale feasibility studies for the establishment of oil-seed and cellulose producing crops on mine tailings have been successfully conducted over 1 growing season with the purpose of these crops to be used as feedstock to the biofuels industry. An acid sulphide tailings impoundment in Copper Cliff, Ontario and a near neutral pH goldmine tailings impoundment in Timmins, Ontario were both tested by amending half hectare plots to approximately 1 m thick with residual biosolids from the pulp and paper industry and growing canola and corn on these plots. Full scale agricultural equipment was used to cultivate seed and harvest the plots to prove the full scale feasibility of farming on these biosolids. The vegetation development, growth, yield, quality and composition were assessed to identify the best species that would maximize biomass development for feedstock to the biofuels industry and carbon credits for the mining industry. Groundwater, biosolids and tailings chemistries were investigated to identify potential deleterious impacts of degrading organic matter on tailings metal mobility. Preliminary hydrologic investigations using moisture sensor profiles elucidate potential conservation of water in amended plots. Tailings amended with biosolids have the potential to provide the mining industry with carbon credits and supply feedstock to this new industry while reclaiming brownfields to a new level, utilizing industrial and municipal organic waste material.

May 1, 2009

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001

By A. Mitura

The paper presents the initial investigation of possible energetic applications of chosen wastes from groups: 06, 03, 05 and 01, including coal slimes being secondary product of hard coal processing. These categories of wastes are catalogued according to the polish law, where 06 ? wastes from production, preparation, purchasing and application of products of non-organic chemistry; 03 ? wastes from wood processing and from plates and furniture, celluloid mass, paper and card board production; 13 ? oil wastes and wastes from liquid fuels; 01 ? wastes produced by searching, extracting, physical and chemical processing of ores and other mineral raw materials. The change of combustion heat value was evaluated in produced energetic mixtures containing these types of wastes together with the change of their individual components. All combinations of ingredients were taken into consideration giving 256 various mixtures, from which 36 were selected to investigation. This allowed the performance of statistical factor analysis. For such prepared materials the application of regressive method was proposed in purpose of calculating combustion heat value and then the comparison of empirically determined and theoretically calculated heat values was performed. The change of regressive coefficients can be determined by the nature of Hess law (eq. 1) what was investigated and the attempt of its explication and validation was done.

Aug 1, 2013

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By G. G. Bowser

Introduction Flame shots are of very infrequent occurrence in the coal mines of Nova Scotia. Probably not more than one is recorded in three months. Many shot-firers have never experienced one, and many never will. As a consequence, although all such occurrences are very carefully investigated, information concerning the cause of flame shots is somewhat meagre. In the course of the years, however, something has been learned of the practices and conditions that are responsible for them. During the past ten? years, over seventeen million shots were fired in the coal mines of Nova Scotia and only fifty-two faulty shots were reported or investigated during that time. In thirty-nine of these, flames were reported; in five, sparks only; and in eight, smoke only. In eight of these occurrences, unburned explosive was found after firing. In one of these eight, flame was seen in the back part of the hole, and an accompanying hissing sound pointed to burning explosive. In four of them, there was no evidence that gas was not ignited. All samples of explosives from these faulty shots which were submitted for analysis were found to be normal, except two, in 1937, which contained excessive moisture. These two samples were from two following shots in the same room on the same day. The initial cause of trouble with all eight shots was one or several of the following: explosives in poor condition, separation of cartridges, incorrect priming, shot hole in poor condition or not properly cleaned. In the case of sixteen or seventeen of the thirty-nine shots which flamed, data are insufficient for conclusions to be drawn as to the cause of the flame.

Jan 1, 1947

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By R. D. MacEchern, M. C. Rockwell

"This paper describes the research and tests carried out to recover the readily available barite from the tailings produced by the Nystone Chemical Ltd. operation at Debert, N.S. The tailings comprised 70-80% of the original feed and contained about 20-25% Baso4 .The objective of the research, undertaken during 1982, was to produce a barite concentrate which would meet the American Petroleum Institute (API) barite requirements for use in drilling mud. Samples from the tailings pond were examined and analysed to determine the tailings characteristics.Preliminary test work was performed on the tailings samples using a Haultain Superpanner, Wilfley tables and Humphrey's spirals. The grade of the barite concentrate retrieved did not satisfy the API barite requirements.The fineness of the tailings and the fact that approximately 80% of the barite was contained in the -200 mesh (0.074 mm) size fractions, indicated that flotation of barite from the tailings might be successful."

Jan 1, 1984

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By T. Eger

Load Haul Dump vehicles (LHD) are extensively used in underground mining however equipment design and operating conditions contribute to restricted operator?s visibility. The inability to clearly see people, objects or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines visibility assessments are traditionally completed in the field. However, field methods are unable to evaluate visibility under dynamic operating conditions and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height, for example. Results of this research show computer simulation and virtual reality can be successfully used to evaluate visibility during the operation of LHD vehicles. In order to benefit from virtual reality applications the work environment, LHD vehicle and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic ana lysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHD vehicles were developed from manufacturer specifications and pictur es taken from LHD vehicles currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle and the vehicle and human where driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired visibility were successfully identified with this method. The JACK program can also provide real-time feedback on the human?s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHD VRML files imported into JACK have also been combined with environment files into other VR software packages (e.g. Maverik) to view in a VRL facility, managed by MIRARCO at Laurentian University. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial visibility issues.

May 1, 2003

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By A. Ockewitz, A. Trondl, D. -Z. Sun

"Numerical simulation of extrusion processes offers an efficient method for tool design and optimization of geometries and properties of extruded parts. However, until now there are few systematic investigations about influences of material model and different parameters e.g. for friction and thermal processes on calculated local and global responses. Since extrusion processes are essentially influenced by friction between billet and extrusion tools, new friction tests were performed in this work to develop a reliable friction model. Compression and torsion tests were performed at different temperatures and velocities to calibrate the material model for extrusion simulations. Extrusion processes for circular rods and U-profiles were conducted at TU Berlin with backward and forward extrusion for different extrusion ratios, billet temperatures, product velocities and cooling conditions. This work focuses on numerical simulations of the extrusion tests with the FE code HyperXtrude. Based on the calculated distributions of local strain, strain rate and temperature the recrystallized volume fraction and grain sizes were calculated with empirical models and compared with the experimental results from optical micrographs and EBSD scans. The calculated total and friction forces and temperatures were compared with the experimental results and the deviations between experiment and simulation were analyzed.INTRODUCTION Extruded aluminum components are widely used in vehicle constructions due to light weight and manufacturing consideration. Local mechanical properties in the components are inhomogeneous as a consequence of the spatial distribution of microstructure which is influenced by numerous factors like material composition, temperature, tool design, friction, extrusion ratio and speed during the extrusion process. For the optimization of the extrusion process with regard to all these factors numerical simulation can be an essential tool. Based on results of finite element simulations of the extrusion process the microstructure in the extruded components can be predicted and then the resulting mechanical properties can be numerically determined instead of by costly trial and error methods. The aim of the work presented in this paper is the development of a numerical method for the simulation of extrusion processes with modeling of microstructure."

Jan 1, 2018

In Canada and other countries, legislation dealing with accurate factual disclosure for mining projects is being expanded to include more metallurgical design information. Grinding characteristics, metallurgical recovery of contained metal and environmental hazards associated with tailings disposal will be part of the Canadian package. This paper will examine only that portion of the plant design standard practice that relates to grinding ? in SAG mills and ball mills that grind ore from as received crushed material to final ground product that is fed to downstream plant recovery processes. Since grinding plants represent a significant portion of the overall concentrator cost, accountability in grinding design should no longer be left to chance, opinion, or hidden proprietary information. This is the 21st century. It is reasonable to expect that a factual basis will be needed so that a Qualified Person (QP) reviewing the grinding mill design can understand it. That will also involve how many and what quality of samples are taken to define the characteristics of the deposit, the accuracy of the tests used to measure ore hardness and the method by which the dimensions and power of the mills are determined. If these criteria are not met, the QP may have no choice but to call attention to the lack of convincing information regarding the grinding mill design for the project. At the same time clients are expected to demand getting the correct design information at a cheaper price, results in a more timely way, and accurate design to the point where the risk of tonnage shortfalls are reduced or eliminated. Tables will be presented to show how this can be done to current standards using existing technologies. At the same time it is acknowledged that current standards are ill-defined and that to achieve consensus among those involved in SAG mill design work, it may require that a consortium funded project be set up to establish what tests and methods for grinding design are suitable to meet the new standards for metallurgical disclosure. By running parallel design methods on several major projects over a period of 5 years, the process of how to design grinding circuits will be better understood because the projects will start at the design stage, include procurement of the mills and will end with a benchmark test on the plant. Selecting the samples and the best schedule for doing test work on core samples submitted and mill design, will be discussed in this paper. The issue of completing the grinding design in time for early procurement decisions is on the critical path for most major projects. Discussions between mining engineers, geologists and process engineers are needed early in the development cycle, at the scoping study level (SS), preliminary engineering assessment (PEA), prefeasibility study (PFS), and at the feasibility study stage (FS), to ensure that proper planning for design sample selection is done. Using adequate sampling and testing methods in a timely way allows early procurement of the grinding mills and minimizes project risk.

Jan 1, 2012