Search Documents

By Pierre Gaucher

It is possible to selectively mine an orebody by combining the use of the SSW probe with any bulk mining methods as well as narrow vein exploitations. In other words, thanks to the use of the SSW probe, mining operators will be able to reduce and control dilution that is generally associated to every mining operation. Already, quick and substantial savings have been obtained. Falconbridge mines have demonstrated in Sudbury and Raglan operations, that the SSW probe can log nickel, copper and iron sulphides in blast holes. They have raised the grade and reduced dilution by outlining the limits of the ore zones before selectively loading explosives in the blast holes. By lowering the probe in a blast hole, a profile of the ore content is instantly measured and recorded. Logging cored diamond drill holes at the mine have demonstrated that the ore content (nickel, copper, cobalt, PGM) as assayed is proportional to the intensity of the probe?s electromagnetic response (EM), probably because the nickel / pyrrhotite ratio is uniform within a given orebody. The probe also measures the intrinsic conductivity of the sulphides and the percentage of magnetite. All probe readings are displayed and automatically stored at a 10-cm interval within the same reading unit. A 30-meter blast hole takes less than 2 minutes to survey. The whole instrument is light (12 kg) and very simple to use. One operator can carry the SSW system and survey either down or up-holes. The probe works from ?40°C to +50°C. Plotting the measurements of the SSW probe in blast holes (2-3-4-6-10 inches in diameter) before blasting allows to determine the exact shape of the orebody within the waste rock and uneconomic low-grade ore. Thus, only the portion of the holes that contains ore is blasted. The dilution is then much reduced and, by leaving the waste and low-grade ore in place, the mine saves on transportation, blasting, crushing, backfilling, milling, etc. Thousands of dollars are thus saved. Some savings may also be achieved during the development of stopes by guiding development drifts and by replacing diamond drilling by percussion drilling. In some circumstances, when the probe shows that some of the rich ore was not drilled-off, additional blast holes will allow to recover pockets of rich ore that otherwise would have been abandoned in the walls of a stope.

May 1, 2001

By Ch. Enkhbold

Underground mining of minerals is becoming an increasingly complicated technological and ecological problem. It can be explained both by worsening of geological conditions of mining and by a specific character of mining industry, which, in contrast to processing branches of industry, intrudes into one of principal components of the nature ? the Earth's interior. At a traditional organization of mining industry, the entire volume of the produced rock mass is brought to the Earth's surface, where valuable components are extracted. This entails not only power over expenditure for long-distance transfer (especially in the vertical direction) of the waste rock forming a part of the original mineral, but also the formation of huge volumes of worked-out spaces. The latter leads (nature cannot stand emptiness!) to an irreversible development of geomechanical processes of shifting of overlying rock masses resulting in an irreparable damage of all surface structures located on the territory undermined by deep mining. Owing to their high productivity combined with low power consumption and instrumental compactness, novel bifunctional technological processes of minerals dressing successfully solve the problem of rock mass processing in underground conditions with subsequent operative disposal of final tailings of such underground dressing in the worked-out space. Besides, an integration of two processes into one is achieved, for example, a decrease in the rock mass coarseness with a simultaneous precise separation of valuable and waste components.

Aug 1, 2013

By C. Groccia

As the search for new ore bodies drives mines to be developed at greater depths, the associated high stress environments present challenges for rock support design. Excavations in highly stressed brittle rock are often subject to large volume increases due to rock failure, a phenomenon known as rock mass bulking, which can result in significant wall convergence. Support systems need to be designed to minimize the amount of bulking and to accommodate large wall convergences. In order to design such a support system, empirical guidelines are often used to predict the amount of bulking. However, the empirical guidelines that are currently available are based on a limited number of case studies and consider few input parameters, which may result in an inaccurate bulking assessment. This paper describes methods of collecting quantitative field data at Creighton mine in Canada to better understand rock mass bulking and to further develop the empirical guidelines for bulking assessment for tunnels in highly stressed grounds. Measuring

Aug 1, 2013

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By A. Taylor

This paper considers mineral processing in zero gravity dry environments typical of asteroids or comets. The electro-dynamic separation technique using pneumatic flow systems is explored. Pneumatic delivery of solids is used because of extreme temperature changes and the possible scarcity of water. The present earth-based process and how it can be modified for these conditions is examined.

May 1, 2001

By Muhammad Usman Siddiqui

Managing and analysing the vast amounts of data collected in a mining project effectively is crucial for enhancing the project's economic feasibility. The efficient utilization of this data is critical to minimising the time spent on projects and increasing project value. Process engineers can effectively integrate geometallurgical data into plant operations by employing analytical tools like Python, significantly optimizing the mine-to-mill process. This practical approach is a game-changer in the mining industry. Classifying a geomet dataset into units of similar characteristics (properties of the ore) is an important outcome of a geomet study. This approach simplifies data classification, allowing for class-by-class process modelling, which improves the decision-making process in mine planning and development. Classifying a geomet dataset involves using grade, lithology, and test work data (if available) to create blocks of similar characteristics, known as ‘geomet units.’ Compared to conventional methodologies, these units provide context and empirical evidence that can be more accurately mapped onto block-by-block process flowsheet development and net present value (NPV) estimation. This robust classification method reduces a project's technical risks and influences the initial mine planning sequence to maximise profitability. Defining robust geomet units with data sets with similar material is challenging due to the vast amounts of data available and the database's high heterogeneity. The methodology's purpose is to minimise time-consuming low-value-adding aspects of geometallurgy. The approach is different for a greenfield and a brownfield study, as all the valuable data in a brownfield process can be utilised to define the geomet units. Python has various libraries providing multiple machine-learning algorithms to assist in classification. The k-means algorithm is used for clustering, and the SHapley Additive exPlanations (SHAP) method is used to quantify the effect of each feature on the clustering results. However, even with automation, the methodology still requires a keen eye to account for the nuances that appear from project to project.

Oct 1, 2024

By Ron Doucet

Industry today is now more than ever dependent on its assets and on the standard of maintenance. Changes in technology, environmental regulations, a continually improving focus on safety and global competitiveness has made maintenance a key activity in sustaining safe, financially viable and environmentally integral operations. Maintenance used to be looked upon as a cost centre with a sole focus of fixing equipment to attain high availability. Maintenance today affects all aspects of the business: safety, environmental integrity, energy efficiency, productivity, costs, and product quality. These new demands on the function of maintenance requires us to think vastly differently about what maintenance is all about, even to the point of contradicting old beliefs. In the following paragraphs we will examine some of the changed thinking that has evolved over the last 50 years. These new concepts will lay the foundation for the implementation of 21st century best practice maintenance.

May 1, 2003

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By C. V. Corless

THE origin of various types and groups of ore deposits was some years ago a subject of much controversy. To this statement the copper-nickel deposits near Sudbury afforded no exception. Not since the Report of the Ontario Nickel Commission, in 1917, has there been any serious discussion of the origin of this very important group. This may be because, from the opening-up of Murray mine by the British America Nickel Corporation until the recent work at Frood mine, no new ore-body of importance has been developed in the district. The controversy fifteen or twenty years ago between those who favoured the theory of magmatic segregation, among whom Dr. A. P. Coleman was the leading exponent, and those who considered that most, if not all of the Sudbury deposits could more satisfactorily be accounted for by the theory of replacement, will be remembered by many members of the Institute. Perhaps, as too often happens in controversial discussion, each side tended to overemphasize the importance of those geological phenomena which seemed to be most easily accounted for by the theory it favoured. A more balanced view would perhaps admit that replacement was probably predominant in the formation of most of the offset deposits, and magmatic segregation in that of most of the marginal deposits . But there is danger in generalization. Each body of ore should be studied by itself, and no general conclusion of this kind should be allowed to warp the judgment in making such a study.

Jan 1, 1929

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By R. A. Sudisman, T. Yamabe, M. Osada

"Geological material can be subjected to some different loading conditions, mainly due to three inter-related physical processes which are mechanical, thermal, and hydrological. Freezing and thawing process of rock that occurs in sub-zero temperature condition may contain some or all those three physical processes depended on its initial condition. Those inter-related physical processes may lead the ground into failures. Therefore, understanding the physical properties such as deformation process of geological material under freezing and thawing condition is required for the artificial ground freezing projects and engineering construction activity in the natural cold region.In order to study the strain characteristic of rocks during freezing and thawing process, a series of freezing and thawing experiments of core samples of three different rock types and mortar has been conducted under varying temperature from -20 °C to +20 °C. Four core sample types are Sandstone, Granite, Tuff, and Mortar with 50 mm diameter and 50 mm height, which were naturally dried before the freezing-thawing experiment. Freezing-thawing experiment was conducted by submerging the vinyl covered core samples into a temperature-controlled liquid coolant box. Firstly, temperature of liquid (brine solution) was set at -20 °C so that the temperature of subjected sample was decreasing to as low as -20 °C. And then the temperature of brine was returning to initial room temperature after the coolant system was stopped. Strain gauge and thermo couple were attached on the core’s perimeter to measure strains and temperature changes.Sandstone and Mortar samples show relatively similar results than other two samples. Both presents linearly shrink with the temperature decrease and expand almost to its initial condition with the temperature increase. Granite shows less-linear strain-temperature relationship during thawing process, while the Tuff sample shows abrupt strain increase during thawing process on the temperature higher than +10 °C. Thermal expansion value of each rock types were obtained by fitting the major strain-temperature relationship on -19 °C to +10 °C temperature range. Overall, anisotropic deformation was observed on the entire samples and possible mechanisms for each hysteresis characteristic are discussed, which need to be confirmed by further experiments."

Jan 1, 2015

By Maxim Martel, Karolan Tremblay

Westwood Mine has experienced several episodes of increased seismic activity. While current geotechnical characterizations such as RMR, GSI, and Q' index can identify the general rock quality and zones at risk of convergence, they fail in identifying zones at risk of seismic activity. Previous research at Westwood Mine has shown a correlation between seismicity and areas with strong rheology contrasts. To characterize this contrast, 300 UCS tests were analyzed with their associated geochemical data, and statistical analysis and regression were performed using IOGAS software to establish a relationship between resistance and geochemistry. UCS-generated data with XRF results were transferred to Leapfrog Geo to create a block model of intact rock strength. This block model dataset was used to perform a competency contrast block model, and back-analysis of specific seismic sectors at Westwood Mine were conducted to validate the model. The purpose is to develop an established geomechanical tool capable in identifying areas with greater seismic risk associated to a change in the rock strength characteristics. By identifying those areas, mitigation measures can be implemented to minimize impact of seismicity on the operation.

Jan 1, 2023

By Jan Nemcik

Among other products steel mesh has been used successfully for many years to support strata and minimise loose material from falling into the mine opening. Installation of steel mesh has proven to be difficult to automate and many other products, such as Thin Spray-on Liners (TSL), have been proposed as a replacement. Ideally, the mechanical properties of these products should be superior to those of the steel mesh, however, most TSL trialled in mines to date have been weak and in addition have had slow cure times, as a result none of these materials can seriously compete with steel mesh. Now a new polymer product that cures in seconds and forms a stiff strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong. To enable selection of a suitable polymer material for roadway skin reinforcement several numerical models were constructed to investigate the role of interface roughness and the influence of polymer stiffness on load transfer along the rock-polymer interface. Laboratory tests indicate that the shear adhesion of the rock-polymer interface can be substantial while the tensile adhesion can be much lower. The models indicate that the natural stone roughness and surface waviness plays a major role in shear adhesion while the elastic properties of polymer liner can significantly influence the polymer ability to resist fracture opening.

Oct 1, 2009

By P. Fleming, W. Pascheto

"Rod mills processing nickel and copper ore experienced recurring failures of liner bolts. In some cases failures became very frequent, requiring constant mill intervention and consequently impacting process stability and operating costs. Investigation related to the causes of bolt failures involved a multidisciplinary approach with the participation of engineering, maintenance and operation. It included the determination of bolt failure mechanisms as well as the assessment of mechanical properties, fabrication quality and handling and installation procedures. In addition, other parameters affecting bolt performance such as mill and liner design, operating parameters and maintenance practices were studied. This paper reports the failure investigation results and proposed solutions for failure prevention. INTRODUCTIONOccasional liner bolt failures are common in rod mills. However, chronic bolt failures developed in rod mills processing nickel and copper ore caused frequent shutdowns for bolt replacement to an extent that affected process stability. At first, it was thought that the cause of recurring failures was related to bolt quality. The operation then submitted several failed bolts to failure analysis. However, it became apparent that bolt quality was unlikely to be the main cause of failures. The determination of root cause (s) then became more complex, requiring a multi-disciplinary approach to failure investigation, requiring the assessment of bolt installation methods, mill design, operating conditions and maintenance practices. The results of the metallurgical failure analysis and investigation of other possible causes of failures are reported here."

Jan 1, 2016

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By Jeremy P. Richards

Key inputs are volatiles and heat: Slab dehydration: Breakdown of amphibole and serpentine in hydrated oceanic crust releases fluids into mantle wedge, causing metasomatism.

May 1, 2008

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009