Search Documents

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015

By James Walters, Samuel Sideras, Kathryn Petek

The Oregon Department of Transporta­tion {ODOT} is currently performing a seismic retrofit and widening of the Abernethy Bridge as part the 1-205: Stafford Road to OR213 Improvements Project. The Abernethy Bridge, located in Clackamas County, conveys traffic over the Willamette River between the cities of West Linn and Oregon City. The existing bridge structure was completed in 1971 and is approximately 2,700 ft {820 m) in length and consists of 14 piers and two abutments, not including on­and off-ramp structures. At the bridge ocation, the Willamette River is approximately 1,050 ft {320 m) wide. The main channel crossing structure comprises three spans up to 450 ft (137m) long supported on Piers 3 through 6. The west approach structure includes nine continuous spans up to 195 ft {60 m) long and supported on Piers 6 through 14 and Abutment 2. The existing bridge piers are supported on a combination of driven steel H-piles and shallow foundations bearing on basalt bedrock. Construction of the bridge widening and seismic retrofit began in July 2022, which will add one lane in each direction and increase the width of the existing bridge from 100 ft (30 m) to 140 ft {43 m). The seismic retrofit will improve bridge performance to con­temporary seismic design standards and feature a two-level seismic design approach including both operational and life safety design and performance criteria. The foundation design for the project was driven by the highly variable geologic conditions across the project alignment, site constraints and the significant seismic demands. To meet the seismic performance criteria, the foundation solutions for the widening and seismic retrofit included micropiles, ground improvement and drilled shafts up to 12 ft (3.6 m) in diameter. This article describes the foundation design process and methodology and the foundation mitigation solutions developed for the project, as well as discussion of using 12 ft {3.6 m) diameter drilled shafts to mitigate the impacts of deep-seated permanent soil displacements.

Sep 1, 2024

By Les R. Chernauskas

Driven pipe piles are commonly used for near and offshore structures due to their omni-directional bending resistance, large surface area, and ease of installation. However, these piles typically cannot be driven deep enough to develop significant and sustained uplift capacity, and in some cases do not generate enough end-bearing resistance before being overstressed during driving. When driven closed-ended, their relatively light weight to cross-sectional ratio, and when driven open-ended their tendency to prematurely plug, are some installation short comings. Spin Fin® piles are traditional pipe piles fitted with flat, steel plates (?fins?) attached at a slight angle over the lower few feet of the pipe. Their design development dates back several decades for projects associated with harsh, limited weather window, offshore Alaskan oil field work. These projects required a pile type that could generate high and sustained capacity in both compression and tension, at relatively shallow depth. During pile driving, a relatively short, high capacity pile translates into more rapid installations with smaller and more efficient equipment. In this type of environment, where pile capacities are large, cyclic loading is typical, and relatively high pile movement is tolerable, the Spin Fin® pile is a superior solution. This paper describes the experience of using Spin Fin® piles on several recently completed Massachusetts Steam Ship Authority projects.

Jan 1, 2011

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By Kenton W. Braun

Concourse B at the Anchorage, Alaska International Airport is currently being renovated while retaining the original building structure and foundations. Part of the renovation includes the installation of a new, permanent baggage tunnel system beneath the existing building. Installation of this cast in place concrete tunnel, beneath the existing structure, required installation of a steel retaining wall to support footing loads above the base of the excavation. Construction of this retaining wall presented challenging and unconventional design and construction methods. Detailed discussions of the design and construction techniques utilized for this project are outlined.

Jan 1, 2008

By Frank Rausche

Why testing What tests can be done Dynamic load testing Loading device Measurements Analysis Examples

Jan 1, 2001

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By Edmund J. Cardoza

The Detroit Water and Sewerage Department (DWSD) provides water and wastewater services to the Greater Detroit Metropolitan Area. Sewerage is treated at the DWSD Wastewater Treatment Plant (WWTP) located at 9300 W. Jefferson Street south of the City of Detroit, Figure 1. PARTICIPANTS Engineering and design of the project for the DWSD was performed by Harza Engineering Company, Inc., C.C. Johnson & Malhotra, P.C. and their sub-consultants, including Worley Engineering and Wade Trim. The Prime Contractor is a Joint Venture of Traylor Brothers, Inc. and Jay Dee Construction. The shaft drilling and riser installation was performed by The Millgard Corporation in joint venture with the Prime Contractor (MTJD). The selection of specialized drilling equipment and the supervision and performance of the access shaft and riser installations was primarily the responsibility of The Millgard Corporation (TMC).

Jan 1, 2001

By Bengt H. Fellenius

It is a truism that in the design of pile foundations one must consider both capacity and settlement. As to capacity, most basic text books contain simple methods of design of capacity of single pile. More sophisticated methods are the subject of many journal papers. However, methods for design considering settlement of pile foundations are scarce. (Most confuse settlement with the movement due to load-transfer?the transfer of load from the pile to the soil). Furthermore, for both capacity and settlement, most methods include several simplifying assumptions regarding soil layering and neglect the effect of the frequently occurring fill and excavations, as well as changes of the groundwater table and pore pressure distribution. Therefore, the methods may provide qualitative results, but not quantitative. Because of this situation, pile design often appears as somewhat of a guessing game and a very subjective?and risky?occupation. This need not be. Pile foundation design is controlled by three factors: capacity, strength, and settlement requirements and these have been combined in a method called "the unified design of piles and pile groups considering capacity, settlement, and negative skin friction" (Fellenius, 1984; 1989), which method is summarized in this guide.

Jan 1, 1991

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000

By Ivan Hee

The 2.5km long bridge over the Beauharnois Canal and St. Lawrence Seaway is a major structure in the new Autoroute 30 project near Montreal. Foundations for the bridge consist of footings on bedrock, driven piles, and drilled shafts. This paper describes the design, verification, and construction of 1.85m diameter drilled shafts socketed into very strong and abrasive dolomitic sandstone. Two loading tests on sacrificial, heavily-instrumented, 1.18m diameter test shafts using Osterberg load cells were performed, with telltales installed to monitor a possible rock cone failure mechanism. The loading tests resulted in a revision to the initial design and provided a greater understanding of the cone uplift mechanism in rock. Insights gained are discussed and economies of the load testing program presented. Construction methodologies are also presented.

Jan 1, 2011

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2013

By Rudolph P. Frizzi

The current trend of increasing augered cast-in-place (ACIP) pile diameter, length, and load carrying capacities demonstrates improvements in installation equipment, increased acceptance, and that quality control is being successfully implemented by the parties involved in the ACIP pile construction process. Quality control is essential for ACEP piles since 24- to 36-in-dia (610-to 915-mm-dia) piles are currently being constructed to sustain design compressive loads of 800 to 900 kips (3555 to 4000 kN). This paper presents a summary of ACIP pile quality control procedures and methods beginning in the design and bid process, through ACIP pile installation, to post-construction. The results of a recent survey of contractors, engineers, equipment suppliers, and researchers routinely involved with ACIP piles in the United States, Europe, and the Middle East are included to address current trends in ACIP piles and quality control.

Jan 1, 2001

By Alice Y. Tseng, Dan MacLean

"Corrosion protection of all deep foundation systems made of steel is THE issue when considering durability of the element in the long term. Protecting steel from corrosion and maintaining the steel tendon cross sectional area ensures a competent and durable system. The foundation of a building is usually difficult to repair and therefore high risk is taken when unknowingly choosing a non-adequate solution.Requirements according to EN 1990 (Eurocode 0 or EC 0) on construction durability requires a service life over 100 years. How can a service life over 100 years be achieved? How shall bare steel be protected in soil, which sometimes could be an aggressive environment to the steel? Which corrosion protection methods are commonly used in Europe and in North America?This paper will focus on hollow bars used as Micropiles, Anchor piles and Soil Nails. It gives an overview about the state of the practice in regards to corrosion protection (including head construction) and evaluates different options following the European Standards focusing on type of material and method of installation. Further the different corrosion protective methods such as thickness of grout body, coating types and sacrificial loss are listed with the pros and cons evaluated.Based not only on North American standards like FHWA “Micropile Design and Construction Guidelines”, FHWA Geotechnical Engineering Circular No. 7 for “Soil Nail Walls“ and Post-Tensioning Institute “Recommendations for Prestressed Rock and Soil Anchors”, but also European standards like EN 14199 “Execution of special geotechnical works – Micropiles”, EN 14490 “Execution of special geotechnical works - Soil nailing”, EN 1537 “Execution of special geotechnical work – Ground anchors“, and other relevant standards, all possibilities of protecting the hollow bars and the steel quality will be introduced, discussed and compared ."

Jan 1, 2017

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Aaron Gallant

Civil engineering and construction companies are increasingly aware of the environmental impact and associated greenhouse gas (GHG) emissions linked to their daily operations and design decisions. Many have already taken significant steps to track and report emissions to better understand their impact on the global carbon footprint. Most generally align accounting practices with the Greenhouse Gas Protocol {GHG Protocol), which has become the most widely adopted international framework to measure and report GHG emissions. The GHG Protocol was developed by the World Resources Institute and the World Business Council for Sustainable Development and categorizes emissions into three scopes. Scope 1 constitutes direct emissions caused by operating equipment and resources it controls and owns (e.g., fossil fuels to run machinery, vehicles, etc.). Scope 2 incorporates indirect emissions linked to purchased electricity, heat, or energy owned or operated by a third party, but influenced by the individual entity's usage. Scope 3 encompasses all other indirect emis­sions associated with entity operations. In other words, Scope 3 attempts to put a spotlight on the indirect emissions within an entity's entire value chain that allow the entity to operate and provide a service.

Nov 1, 2024

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

Jan 1, 1993