Search Documents

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By Richard T. Stain

"In 2001, a pile trial site was established at Limelette in Belgium consisting of 25 displacement screw piles and 5 driven pre-cast piles. Interested parties were invited to participate in a pile prediction event, whereby they would submit predicted static load test behaviour in the form of load settlement plots. These predictions could be based on soil investigation results supplied by the organizers, or dynamic load test measurements.Following the submission deadline, the organisers released the results of static load tests for comparison.Of all the six participants, including Statnamic, the SIMBAT method was independently accredited with achieving the best predictions.This paper examines at the differences between SIMBAT and other systems, and presents the correlations from the Limelette trial.INTRODUCTIONThe Belgian Building Research Institute (BBRI) initiated an ambitious research programme involving the construction and testing of some 60 trial piles spread between two sites, a clay site at Sint Kateline Waver and a sandy site at the BBRI headquarters at Limelette. The project was financed largely by the Belgian Ministry of Economic affairs. (ref 1.) This paper refers only to the second site.At Limelette, six different types of displacement pile were installed: one driven pre-cast and five cast in place screw piles - Atlas, DeWaal, Fundex, Olivier and Omega. A detailed site investigation was carried out including in-situ and laboratory tests.An international pile capacity prediction event was publicised, participants being invited to predict static pile behaviour. Predictions could be based on:"

Jan 1, 2005

By Mark R. Svinkin

"Construction equipment and operations usually produce soil and structural vibrations which may harmfully affect various structures and also the content of buildings and houses. The level of structural vibrations depends on a number of factors such as characterized sources of vibrations, soil conditions, and susceptibility of structures. There are certain knowledge and experience for managing the effects of construction vibrations which require implementation of condition survey of structures, information on construction dynamic sources and soil conditions at a site, evaluation of possible vibration effects on structure, calculation of ground vibrations before construction, use mitigation measures to decrease vibrations, and a choice of appropriate vibration limits. The paper presents the application of known concepts for assessment of vibration effects on structures from bridge constructions.INTRODUCTIONVibrations producing by construction activities such as pile driving, dynamic compaction of loose soils, demolition work, heavy construction equipment and trucks can affect adjacent and remote structures. Vibration effects on structures, sensitive devices and processes may create significant practical problems. Legal actions are often required for solutions of vibration consequences. The level of construction vibrations depends on dynamic sources, soil conditions at a site in particularly availability of soils with settlement potential, distances from the sources, parameters of waves propagating at a site and susceptibility rating of adjacent and remote structures. It is likely that intolerable structural vibrations from direct vibration effects of impact pile driving and resonant floor vibrations from vibratory pile driving may be induced in adjacent structures to construction sites.Foundation settlements resulting from soil vibrations in loose soils usually occur in the proximity of dynamic sources, but it is important that dynamic settlement may happen at various distances from the source. There are such examples. First, Kaminetzky (1991) mentioned a case history of building settlements developed at a distance of about 305 m (1000 ft) away from a pile driving site. Foundations of the buildings were underpinned on piles down to the tip elevation of the new driven piles to prevent building settlements. Second, Lacy and Gould (1985) shows that the peak particle velocity (PPV) of 2.5 mm/s (0.1 in/s) of ground vibrations could trigger dynamic settlements at distances up to 30.5 m (100 ft) from driven piles."

Jan 1, 2016

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Vivian M. Troughton, Clifford J. Wren, Tony P. Suckling

"Secant pile walls are used for the construction of deep basement walls and earth retaining structures. Risk associated with secant pile walls is commonly perceived as being the safety of site personnel and the public during piling operations, or safety used in design. It is recognized that both of these are of paramount importance, but additional risks associated with the construction methods must also be considered to complete the risk management profile for any project. For the particular case of secant pile walls, if Clients take a ""back seat"" they may be unaware of the total risk package they are procuring. The authors argue that the piling contractor should be involved at the earliest stage giving input into the overall risk management process. Such early involvement within the professional team will maximise cost benefits to the Client and minimise the delays and cost increases sometimes associated with these works. A consistent methodology for identifying and then managing all the risks associated with secant pile walls is proposed. An example is used to demonstrate how this methodology should be employed. INTRODUCTIONThis paper discusses the value of a complete and integrated risk management process for structures with basements formed using a secant pile wall.The risk associated with any secant pile wall can be consicfered as comprising four components;1. Safety of people on site2. Safety of design or design methodology3. Construction risks4. Commercial risksAny risk management system needs to fully consider and integrate each of these four components to maximise the likelihood of a successful outcome for the basement.This paper concentrates on the construction risks for secant pile walls, as these are not often understood by the Client (in this paper the term ""Client"" also includes the main contractor, principal contractor, Engineer, Planning Supervisor, quantity surveyor and cost consultant)."

Jan 1, 2005

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By Alexandra Weidle, Seffen Leppla, Rolf Katzenbach, Matthias Seip

"A lot of different deep mixing systems have been developed in the last decades for a wide spectrum of applications, e.g. retaining and foundations systems, soil improvement, sealing of toxic substances or dyke strengthening. The paper will deal with special aspects of constructions with deep mixing systems for infrastructures like soil improvement for cyclic loadings and underpinnings in difficult soil conditions by presenting cases from engineering practice.1. DEEP DRY SOIL MIXING FOR SOIL IMPROVEMENT OF RAILWAY TRACKS IN VERY SOFT SOILS1.1 IntroductionRailway tracks are set into vibrations by train passing. In very soft soil this leads to long-term deformations which lead to speed limits, temporary closings and big maintenance efforts. The energy of the dynamic loading is transmitted into the soil by compression and shear waves and at the surface by rayleigh waves (Wood 1968). The expansion of the waves are influenced by•,thickness of the soft soil layer•,density of the soft soil layer•,stiffness of the soft soil layer•,saturation of the soft soil layer•,frequency of the dynamic loadingThe frequency of the dynamic loading depends on the train velocity and the distance of the wheels and wheel sets. If the frequency of the dynamic loading is in the range of the natural frequency of the soft soil layer the vibrations increase extremely (Lieberenz et al. 2003). As a result the long-term deformations will increase as well.To avoid these long-term deformations and the resulting operation restrictions and maintenance efforts an adequate soil improvement is necessary. For the optimization of the soil improvement field tests have been carried out.1.2 Experimental field testsThe field tests have been carried out at a 300 m long test track with five different setups, each 30 m long:•,test track TS 0: no soil improvement•,test track TS 1: soil improvement with single lime-cement-columns 5.9 m deep (Figure 1a)•,test track TS 2: soil improvement with single lime-cement-columns 5.9 m and 10.4 m deep (Figure 1b)"

Jan 1, 2015

By Matthew Janes

The new Bow office complex will become the new headquarters of EnCana Corporation, a leading Canadian oil and gas company. The shoring system, encompassing nearly two city blocks and excavated to a depth of 20.5 m, supported surrounding utilities and buildings in downtown Calgary. Past excavations in the area experienced large amounts of rock movement, the mechanics of which were poorly understood. The focus of this paper is the design process and construction results concerning rock movement and the effectiveness of the shoring structure. A lack of information regarding the local in-situ stresses and shear band propagation in the bedrock led to research of case studies in the Calgary area and a peer review from local experts. Several geotechnical scenarios were analyzed using FLAC to account for varying residual rock stresses and the location and composition of weak rock layers suspected of causing shear band movement. Movement characteristics were predicted that would identify the rock deformation mechanic throughout the construction process. A detailed monitoring programme composed of precision monitoring targets, inclinometers, and extensometers was established to provide accuracy and redundancy in establishing the movement of the rock and excavation support structure. The results of the programme were used to identify the rock deformation mechanics and further refine the FLAC analysis. To date, monitoring indicates that localized shear band effect is the leading cause of rock movement. The phenomenon appears to be directionally dependent and strongly correlated to excavation extent.

Jan 1, 2008

By Jim Cook

Arsenal Football Club required the development of a new home stadium in north London, subsequently named the Emirates Stadium. The proposed development comprised a 60,000 seat stadium, with associated facilities and a sports training centre. Described are the foundation solutions and piling construction techniques used, which take into consideration the potential impacts on existing above and below ground railway infrastructure and underground water structures. Methods used by the piling contractor to improve aspects associated with health, safety and quality are also described.

Jan 1, 2008

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over the navigation channel. The subsurface soil profile was quite variable along the bridge alignment. In Virginia, there was fill over soft Alluvial deposits underlain by dense Terrace deposits, as well as remnant foundations from a former ship yard. At the bascule span, there was up to 50 ft of a soft organic silty clay layer underlain by a deep deposit of stiff Cretaceous clay. Along the Maryland approach, there were Alluvial deposits over dense Terrace deposits over stiff Cretaceous clays and dense Cretaceous sands. The variation in subsurface conditions led to the selection of alternative deep foundations that suited the specific conditions and were based on the design phase testing program, from which ultimate design capacities were determined. During construction, there were instances of unexpected pile performance, notably different than that experienced during the design phase testing, requiring changes to the contract installation criteria and re-design. This paper will present the types of deep foundations used for the project, the performance criteria assumed during the design, the measured performance and difficulties encountered during construction, and the resulting remedial actions, i.e., changes to contract installation criteria and/or re-design due to the unanticipated field conditions.

Jan 1, 2009

By Kaushik Mukherjee

"Malaysian offshore and surrounding region are favorable to the installation of driven piles. During the design phase, pile driveability analysis plays a major role in pile make-up design to suit and selection of the feasible hammer, besides defining acceptance criteria to ensure a certain level of confidence of its fitness for purpose. The accuracy level of driveability analyses depends substantially on the selection of its parameters that best represent the in-situ scenario. The most uncertain of the parameters are those related to the soil model. It is noted in various projects in the region, that the consideration of suitable soil resistance to driving, coupled with soil dynamic parameters, significantly affects driving sequence planning, design, material, hammer selection and most importantly pile acceptance criteria. This is particularly relevant for a region that contains predominantly clayey subsoil resulting in large diameter, long friction piles susceptible to driving disturbances and slow strength recovery. Various researchers suggested suitable dynamic parameters and soil resistance during driving calibrated to specific regions. Regional experience suggests a set of soil degradation and parameters to suit the different stages of driving which is corroborated by pile monitoring records during continuous and delayed driving scenarios. The most sensitive amongst all dynamic soil parameters is the skin damping in clay. Smith’s wave theory approach considers a conservative assumption in selecting the parameters in absence of site-specific data, while a different approach may be adopted based on consistency of the clay for a site where the geotechnical parameters are well defined. This paper summarizes some independent studies on the effects of variations in dynamic parameters and resistance at different stages of driving and suitability of choices of different pile make-up and hammers for an optimum design. Similar experiences, coupled with simulation studies and back-analyses of available driving records suggest a reasonable judgment for the region.INTRODUCTIONFixed structures are generally supported in the in-place condition on a pile foundation those may either be driven or drilled & grouted piles depending on the subsoil. The piles may be driven inside the jacket legs or drilled through individual skirts normally grouped in clusters at the base of each leg. The types of subsoil dealt with in the Peninsular Malaysia and Gulf of Thailand surrounding region are conducive to the installation of driven piles only. The design of an offshore pile is fundamentally the optimization of pile length, size and make-up those are suitable to the requirement and supply. An interactive effort combining aspects related to geotechnical, structural and constructability are required to converge into a feasible, safe and economic solution. Other than the checking of the installation feasibility using a set of hammers in a given environment, driveability analysis is also used to define acceptance criteria for a majority of the offshore piles. Unlike short and end bearing piles in sand/soft rock, the piles in clayey subsoil regime often could not be rested on a dense strata where it could be met by a definite set criteria. Usually a measurement of blow counts determined and defined by driveability analyses forms the acceptance criteria to ensure a certain level of confidence of its fitness for the purpose coupled with an optimum penetration. While softness and uncertainty of the soil strata at target penetration may be resulted in possible overdrive, an unusual delay or the presence of an unidentified cemented layer or a boulder may cause early refusal or underdrive scenario. Hence, accuracy of the investigation, driveabilty study as well as the precautionary measures to avoid delays during driving are of equal importance."

Jan 1, 2015

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By Scott M. Mackiewicz

This project includes replacement of the historic vertical-lift span Meridian Bridge (U.S. Highway 81 over the Missouri River) that connects Yankton, South Dakota with rural Cedar County, Nebraska. The new 76-foot wide, 1,590-foot long steel plate girder structure required the use of drilled shaft foundations that extended into the underlying Carlile Shale formation. Designers indicated that an individual drilled shaft capacity of about 2,000 kips will be needed at each of the river piers, and based on the subsurface information, 8 to 10-foot diameter drilled shafts extending to about 115-foot would be required for support of the bridge structure. An Osterberg Load Test was performed on one test shaft to determine the ultimate skin friction and end bearing of the Carlile Shale. This paper describes the design and installation of the load test drilled shaft as well as presents the load test results as compared with predicted design values determined using FHWA methods.

Jan 1, 2008

By Muhannad T. Suleiman

The design of deep foundations supporting heavy buildings, bridges, transmission lines, and highway structures, is governed by lateral loads in many cases. However, due to the use of empirical or semiempirical approaches to develop the soil force-displacement relationships (i.e., p-y curves), a wide range of recommendations are presented in the literature. Recent efforts by the author and co-workers enabled simultaneous direct measurements of soil-pile interaction pressure and lateral movement along the pile length, resulting in p-y curves based on direct measurement. Advanced sensors including sheet pressure sensors and shape acceleration arrays were used in these experiments. The experiments were conducted at the Soil-Structure Interaction (SSI) facility funded by the Major Research Instrumentation Program at the National Science Foundation. This paper focuses on the SSI of single laterally loaded piles. The test pile was 101.6 mm in diameter and 1.42 m long, which were installed in well-graded loose sand. This paper provides a summary of the installation and testing procedures, soil properties, pile instrumentation, measured lateral load-displacement response, strain profile along the pile length, lateral movement along the pile length and the pressures measured at the soil-pile interface. Furthermore, the paper presents measured p-y curves compared to estimated p-y curves using empirical methods available in the literature.

Jan 1, 2011

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By Les R. Chernauskas

? What is Integrity Testing? ? Cross-Hole Sonic Logging (CSL) ? Single-Hole Sonic Logging (SSL) ? Typical Specifications ? Case Histories ? Observations and Conclusions WHAT IS INTEGRITY TESTING? General Definition ? Process in which the condition or structural makeup of an object can be evaluated with respect to defects such as a reduction in cross section (void or crack) or reduction in material strength (water, slurry, soil mixed with concrete). ? If the defect is severe enough, it can reduce or alter the load carrying ability of the object.

Jan 1, 2001

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010