Search Documents

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By Tobias Hansson

The quality of Lime Cement (L/C) columns is to a great extent dependent on the installation procedure. At a site in the south of Sweden, the client reported problems with the installed columns. To evaluate the operator and equipment dependent part of the installation, Hercules Grundläggning AB was appointed as a competitor to the site contractor. The purpose was to install a number of L/C columns with equal installation parameters for both contractors. A total of 65 test columns were installed in June 1999. The geology is a typical Swedish organic soil profile with a top layer of peat overlying gyttja and clay. Two different binders were used in the comparison; blast furnace slag with cement and lime with cement. After installation, the quality of the columns was monitored by penetration tests and a column sampler for extracting whole columns. The column penetration test were performed 28 and 134 days after installation and extraction 134 days after installation. Inspection and tests of the extracted columns showed that by using a fully computer controlled procedure, the contractor produces columns of superior quality and homogeneity.

Jan 1, 2000

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Tracy Brettmann

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2001

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By Robert G. Lenz

Control of ground water for construction purposes is an everyday occurrence in the U.S. Thousands of pumps are in service at any given time. Most of these applications simply consist of pumping water out of an excavation, generally with the aid of sumps. Modern hydraulic and electric submersible pumps permit these procedures because of their ability to pump solids and take air without losing their prime. These procedures work fine up to a point and permit the contractor to control his ground water problems adequately and at minimal cost. When that point is exceeded, the ground water problems sometimes are compounded. Over-application of open pumping techniques can result in slope failures, cofferdam instability, bottom heaving, boils, loss of ground, damage to adjacent structures and utilities, and assorted other maladys which could and should be avoided. This paper will deal with the options involved in ground water control, a discussion of the unwanted side effects of dewatering, and examples of ground water control projects in various cities around the U.S.

Jan 1, 1988

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Derrick D. Dasenbrock

Three piers of a new river bridge are supported on 1.067 m diameter open-end steel pipe piles. At time of drive, and after pile re-strikes, high-strain dynamic capacity values at plan tip elevations, were as low as 23% of design requirements. Pile lengths were extended 20% to 40% deeper than planned at two piers, driving to rock, impacting both the project cost and schedule. The significant discrepancy between predicted and observed capacity was investigated through a series of coordinated dynamic tests; a full-scale test pile was installed and monitored over 221 days by both dynamic and quasi-static methods. Unusually slow strength gains were observed by dynamic monitoring on all piles installed at the site. CPT soundings were advanced at the test pile and through the pile interior to investigate the soil plug. High-strain dynamic methods were found to have significant limitations in properly assessing the long-term capacity of large-diameter open-end pipe piles during driving and short-term pile re-strikes. As the benefits of large diameter high-capacity open-end pipe piles are numerous, the geotechnical community needs to address appropriate construction monitoring and control of these foundation types to take full advantage of these systems. An improved understanding of the physical effects of pile installation and the impact on soil strength assessment while driving and long term soil strength gain should be developed and incorporated into both design and monitoring procedures to avoid either unsafe or needlessly costly designs.

Jan 1, 2006

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Jesse A. Pfeiffer

CPAR, the Construction Productivity Advancement Research Program, is a new initiative of the Corps of Engineers to enhance U.S. construction industry productivity through the development and application of joint-funded research. CPAR seeks to balance the requirements of both the private sector and the Corps of Engineers construction program, to identify research needs that are common to both parties in a partnership for conducting research, and to achieve practical real-world products which will enhance productivity in the construction industry. Increasing costs of doing business has had a major negative impact on much of the nation's industrial base, and research and development (R&D) is among the areas hardest hit. The Congressional Budget Office estimates that since 1984 inflation adjusted R&D outlays in private U.S. firms have risen at an average annual rate of three percent, or about half the rate of gain of the preceding decade. And, despite a significant increase in foreign competition, the portion of gross national product (GNP) devoted to R&D is lower today than 20 years ago. For the case of the U.S. construction industry, the numbers are even more dramatic.

Jan 1, 1989

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By Masaki Kitazume

"Abstract The wet type and dry type of deep mixing methods have been developed and widely applied for on-land and marine constructions in Japan. The quality assurance (QA) of the methods has been usually carried out by unconfined compression test on field stabilized soil sampled by core boring in Japan. In some other countries, stabilized soil excavated by the wet grab sampling instead of core sampling is often subjected to unconfined compression test for quality assurance. There are several merits and demerits in each method, but few studies have been carried out to compare the stabilized soil strength of these two types of specimens to discuss their applicability to practical construction. The author has conducted a series of field and laboratory tests to compare the stabilized soil strength and discuss the applicability of wet grab sampling to QA for wet and dry types of deep mixing method.In this study, the wet grab sampling was carried out at two road embankment construction sites where the wet type and dry type of deep mixing were applied. The cement stabilized soil was excavated at the three depths by a wet grab sampler soon after the DM column construction. The test result is compared with the other test data in the previous study to discuss the applicability of the web grab sampling method for QA of cement stabilized soil.IntroductionThe Deep Mixing Method (DMM), an in-situ soil stabilization technique using cement and/or lime as a binder, is often employed to improve soft soils (Kitazume and Terashi, 2013). A variety of factors and their interactions affect the eventual strength of a deep-mixed column, while some of which are controllable (e.g. binder type and dose) by engineers while the others are not (e.g. soil types, ground temperature, etc.; Babasaki et al., 1997). In addition to laboratory mix tests, which in essence are a parametric study to estimate the influence of these factors on a particular soil’s strength, the quality assurance (QA) practice in Japan usually involves unconfined compression test on sampling cores from the stabilized columns after a given curing period. It has been recognized, however, that the ‘field strength’, or the strength of the retrieved core, quf is on average lower than the ‘laboratory strength’, qul, evaluated by laboratory mix test. Also allowing for the inevitable variability, existing guidelines (for example, PWRC, 2004 and CDIT, 2008) recommend the design quf /qul values of, for example, 0.5-1.0 for the CDM (Cement Deep Mixing; a wet-type technique, in which binder is added as slurry) and 0.2-0.33 for the DJM (Dry Jet Mixing; a dry-type technique, in which binder is added as powder)."

Jan 1, 2014

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and augered displacement (AD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of AD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilzed by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/AD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current AD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2002

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994