Search Documents

By A. J. Partos

Table 4, Page 311 Table 4 Experimental Parameters from Straight Line Interpretation of Mohr Failure Envelope [ ]

Jan 1, 1991

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By Lok M. Sharma

Development of brownfields is of great interest in these days. Such fields are not easily adaptable for foundations of structures. The uncertainties in ground behavior present challenges of unpredictable subsidence that could be detrimental to the build up facility. A desalination plant had to be located along the seashore, close to the needy population and the existing water supply infrastructure. The available site had been developed as a recreational park area over a dumped construction demolition debris landfill along the coastline. To construct a desalination plant comprised primarily of large concrete basin tanks on slab, founded on the debris fill had its challenges. A ground improvement system in the form of vibro replacement stone columns was designed and constructed. Approximately 5,000 stone columns were installed across the site. This paper describes the analysis process, the design, field load testing, and installation of stone columns. Difficulties during construction and monitoring aspects are briefly described. The plant started operations in the summer of 2008 and to date has performed satisfactorily. When properly designed, the development of brownfields is achievable at other sites.

Jan 1, 2009

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; and forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2009

By Axel J. Pollak

Since the late 1960's the Interstate Division for Baltimore City (IDBC) has been planning and developing the Interstate Highway System for the city to meet regional planning goals. The principal goals are to provide convenient access to the central business district and the port while diverting through traffic away from these congested areas. Interstate Route 95, an eight-lane highway carrying north-south traffic, has headed the city's priority list; during the 1970's its construction proceeded steadily from both east and west towards the harbor. Closing the final 8800-ft (2670-m) gap under the harbor will complete Interstate 95's construction. This final portion, known as the Ft. McHenry Tunnel project, will be built in nine construction contracts. Construction costs of the complete project are expected to exceed $700 million, making it the costliest single project in the Interstate Highway System. Full funding is being provided initially by the Federal Highway Administration (FHWA), and the Maryland Department of Transportation will re-pay the 10 percent local share from toll receipts within the first three years of operation.

Jan 1, 1989

By Mamdouh Hamza

The construction of 1200 m length new quay wall located 1,300 m East of the existing Suez Canal bypass and about 1,000 m south of the Mediterranean shoreline is one of the main projects currently under development in Egypt. Due to very weak foundation soil, mainly soft clay, a particular effort, both in terms of design approach and construction feasibility, has been required. The execution of "barrettes" and T-shaped" diaphragm wall panels down to a depth of 65 m and under extremely severe soil condition has been required in order to pass through the upper soft soil and to reach a competent base layer. Very critical and variable hydrological conditions have been also encountered due to the contemporary nearby channel dredging activity, thus increasing the difficulty for maintaining the stability of the slurry trenches opened in soft material. This paper gives a general overview of the project with some emphasis to the most significant design aspects and to the construction of the deep foundation elements.

Jan 1, 2002

By Ramin Motamed, Reza Mohammadi, Zahra Faeli

Finite element methods can be used to analyze the dynamic responses of soil-foundation-structural systems during earthquakes. Therefore, the validation of finite element models with actual seismic recordings is required to benefit from their use in foundation seismic design. In this paper, the acceleration records from the Hayward-I580/238 bridge in California will be studied. At the HaywardI580/238 bridge, three-component accelerometer recordings from two geotechnical downhole arrays at the surface and depths down to 90 meters were used. Furthermore, from 2011 through 2022, 15 earthquakes were recorded at these downhole arrays ranging from Mw 3.4 to Mw 6. However, this paper focuses on the earthquake events within the range of Mw 3.4 to Mw 4.4. Therefore, this study is limited to earthquakes up to Mw 4.4. In the first part of this study, a free-field model of the Hayward-I580/238 bridge site is built using the OpenSees software. Then, in the second part, a drilled shaft of the HaywardI580/238 bridge is modeled. A comparison of the dynamic responses generated by OpenSees with the recorded data from the geotechnical downhole arrays will be used to validate the free-field model, and the acceleration responses from the free-field model will be applied to the drilled shaft. Then, the behavior of the drilled shaft under the applied seismic forces in terms of different calculated parameters (e.g., displacements, reaction forces, etc.) will be investigated. As a result of this study, despite the absence of actual acceleration recordings, obtaining the responses of the soil layers in various depths is possible using a numerical modeling method. In conclusion, not only OpenSees provides a tool for monitoring drilled shaft behavior during seismic events, it provides a robust tool for future drilled-shafts seismic designs.

Oct 31, 2023

By Dominik Gächter, Wojciech Szczepinski, Jakub Bieszczad

Increased requirements for rail transport north of Oslo have forced Norwegian Authorities to invest in the development of double-track rail to decrease traveling time and increase the frequency of the rail service. Part of this development is Tangenvika Bridge which is built on the largest lake and drinking water reservoir in Norway (Mjøsa). Once completed, it will be the longest railway bridge in Norway. The foundation design consists of drilled and driven composite piles. All the works are performed on water and because of its depth, all piles are installed from floating container pontoons instead of jack-up barges. In order to meet the strict steel quality requirements of composite piles, all piles are welded on land in a controlled environment and then transferred onto the transfer pontoons on water. Close to shores, due to the local presence of sensitive soils and the risk of underwater landslides, a total of 78 drilled piles (1016mm) are executed using the reverse circulation method (RC). All piles are drilled 2m into bedrock using a fully integrated ring bit system. In the deepest parts of the lake, a total of 60 driven piles (1430mm) are installed using 350kJ hydrohammer. The bottom of the piles are finished with a closed-ended pile tip, which is the most popular driven pile tip in Norway. All drilled and driven piles are installed in single lengths of up to 85m and net weight of 102t at 1:5 inclination. The lifting process of the piles on the water provides significant challenges for which a combination of 400t crane, 2 transfer pontoons, and a tugboat is used to provide a safe execution method.

Oct 7, 2024

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

With respect to liability damages, claims and costs thereof relating to or ansmg out of contamination, special or non-special wastes, hazardous wastes or pollution in connection with the performance of this subcontract: It is understood that the subcontractor's work and responsibility wholly exclude any requirement to handle such contaminants or to otherwise be responsible for such contaminants, and Subcontractor shall not be nor be considered to be a generator of such contaminants. Contractor shall indemnify, defend and save harmless Subcontractor and its sureties, from and against all liability, damages, claims and costs relating to or arising out of contamination, special or non-special wastes, hazardous wastes

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007

By Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"Over the last 10 years, the Minnesota Department of Transportation (Mn/DOT) has had a very active program of replacing many major bridges, large structures spanning the Mississippi River. The deep foundations for these new structures include both drilled shafts and large diameter open-ended driven steel pipe piles. Most of these projects included load tests, both axial and lateral.The geology of this area of Minnesota includes some interesting foundation challenges, including highly organic and compressible very soft silts and clays to very dense sand and gravel overlying sedimentary bedrock. In some cases scour requires embedment into rock, and the bedrock formations may range from very soft sandstone to very hard dolostone. Artesian groundwater conditions can sometimes complicate drilled shaft construction, but the rock is otherwise very favorable for drilled shafts. Experience with the open-ended driven steel pipe piles (typically 42 and 48 in, 1.07 and 1.2 m diameter) suggest that these piles most often penetrate even dense granular materials to achieve bearing on rock. Experiences with drilled shafts socketed into the soft sandstones demonstrate that these rocks provide very favorable conditions for drilled shafts, so long as suitable construction practices are followed. Here we present several recent case histories regarding the foundation design and construction of major bridge projects in the vicinity of Minneapolis, Minn., including the Wakota Bridge, the I-35W replacement, the Lafayette Bridge, the Hastings Bridge and the St. Croix Bridge. Some lessons learned from construction and load testing of both types of foundations are described along with implications for design in similar soil and rock conditions."

Jan 1, 2013

By Filippo Maria Leoni, George Filz, Wesley Schmutzler, Matteo Bertoni

"The US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilization at the LPV 111 Project (New Orleans, USA). DMM was used for ground improvement/foundation strengthening and consequently to stabilize and support the burden of the new levee. Two different technologies were used: Trevi Turbo Mix (TTM) and Contrivance Innovation Cement Mixing Columns (CI-CMC). LPV 111 is the largest soil mixing project to date in the USA with its more than 18,000 elements installed to a depth of up to 67 feet for a total of 1.7 million cubic yards of treated soil. The preparation and execution of the project presented many challenges from various points of view. The little time available to complete the job led to the simultaneous utilization of eight deep mixing rigs and batch plants which worked 24 hours per day, 5.5 days per week on a stretch of land approximately 5.3 miles long. Given the imposing geographical extent of the project, a four phase laboratory programme and five field validation test programmes, conducted in as many different areas of the project, were completed to design and optimize the grout mixes and the installation parameters. The massive quality control/quality assurance testing programme produced over 500 drilled core holes and over 5,000 tested specimens in order to determine unconfined compressive strength (UCS) and uniformity of the DMM elements. This paper has the purposes of describing the tremendous challenges encountered and providing valuableinformation that may be useful for other future projects, including details not previously published.INTRODUCTIONReach LPV-111 is part of the Lake Pontchartrain and Vicinity Hurricane Protection System designed to protect the city of New Orleans and the surrounding areas from the surge that would accompany a 100 year hurricane event. LPV-111 measures approximately 8.5 km (5.3 miles) long, of which 7.2 (4.5 miles) extend along the north bank of the Gulf Intracoastal Waterway (GIWW) and the remaining 1.3 (0.8 miles) run north and terminates at the CSX Railroad Gate. The Bayou Sauvage National Wildlife Refuge borders the levee on both sides (Fig. 1)."

Jan 1, 2015

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By A. C. Galvis-Castro, R. Salgado, M. Prezzi, E. Ganju, R. D. Tovar-Valencia

It is generally accepted that the unit shaft resistance of piles in sands is lower for tensile loading than for compressive loading. So far, very little attention has been paid to the influence of the installation method on the tensile-to-compressive unit shaft resistance ratio. The objective of this paper is to analyze the effect of installation method on the ratio of unit shaft resistance in tension to that in compression for a model pile installed in a dense silica sand. To study installation effects, load tests on model piles were carried out in a half-cylindrical calibration chamber with digital image correlation (DIC) capability. The model piles were either jacked in one stroke using a constant rate of advance, or pre-installed into the dense sand samples. Digital images of the model pile and sand were taken during the load test and processed using DIC to obtain the displacement field in the sand. It was found that unit shaft resistance was essentially the same in tension and compression for the pre-installed pile, however for the jacked pile, the unit shaft resistance in tension was approximately half of that in compression. DIC analysis revealed that: (1) during the load test, more displacement occurs in the soil domain for the pre-installed pile compared to the jacked pile, (2) for the jacked pile, the magnitude of displacement in the soil domain is greater in tension than in compression and (3) for the pre-installed pile, the magnitudes of displacement in tension and compression are similar. INTRODUCTION Pile foundations can be categorized into two main types depending on the method of installation: displacement piles (e.g., jacked or driven piles) and non-displacement piles (e.g., bored piles or drilled shafts) (Basu et al. 2010; Salgado 2008). The response of these piles to loading can be studied in the laboratory by means of calibration chamber experiments on model piles that are either jacked into the samples, representing displacement piles (Jardine et al. 2005; Lee et al. 2011; Tovar-Valencia et al. 2018), or pre-installed in the sand sample, representing non-displacement piles(Galvis-Castro et al. 2019a; Le Kouby et al. 2013; Tehrani et al. 2016)

Jan 1, 2019

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017