Search Documents

By Steven R. Ahlfield, Ali Ghandeharioon

A wastewater treatment plant commissioned in 1978 is undergoing a major expansion. Planning various phases of the 8-hectare expansion at this site requires an understanding of the site response during and after construction, and the potential impact on adjacent properties and infrastructure. The expansion project requires nominally 5 m of site grading fill for flood protection. The site is underlain by loose to compact fine sand over firm to very stiff clay stratum that extends to great depths. Ground improvement is required to mitigate the liquefaction hazard in the fine sand stratum, and preloading is proposed to reduce post- construction settlements in the deep clay. Site development and foundation systems for the plant expansion project were evaluated by conducting settlement analyses which accounted for the historic and future site loading and 3-D modeling of soil layers with interpolation between borehole and cone penetration test (CPT) locations. The numerical model was calibrated to match short-term and long-term settlements measured at the plant site. The analyses were carried out to assess the effects of past loading, proposed preload and surcharge heights, lateral extents and durations as well as vibro-replacement ground improvement on post-construction settlements. Two design options were considered for the preload footprint across the site and foundation system for proposed facilities. It is shown that limiting the preload extent and founding some of the proposed structures on deep friction piles reduce the predicted settlements of adjacent infrastructure and result in reasonable performance for the proposed facilities. INTRODUCTION A wastewater treatment plant commissioned in 1978 will be replaced with a new plant on an undeveloped portion of the site to provide wastewater treatment for an expanded service area. The existing facilities must remain in operation until completion of the new plant. The site grade will be raised nominally 5 m for flood protection. The large areal extent of the site grading fill and plant structures will cause stress changes extending to great depths in the underlying soils and result in settlement of the existing and new structures. Historic settlement of the existing facilities has been tolerable for plant operations, but no settlement performance data was recorded during site development and post-construction from 1978 to 2007. Development of the 8-hectare expansion at this site is planned in three phases to reduce the overall construction schedule. Planning for each phase requires evaluating the effects of various site development activities from start to completion of expansion and during the design life (i.e. post-construction period), and the potential impact on existing wastewater treatment facilities and adjacent properties and infrastructure including an adjacent viaduct structure. Figure 1 presents the site plan and three distinct site development phases considered for the plant expansion.

Jan 1, 2019

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By Basha Qubain, Kamil Nuzha, Jianchao Li

This article pertains to a 52-story residential high-rise building in the Rittenhouse Square section of Philadelphia, a densely developed area with mixed residential and commercial buildings. The tower is surrounded by Moravian Street along the north, Walnut Street to the south, a residential building to the east and a three-story historic building to the west. It measures 40 m (130 ft) long by 22.8 m (75 ft) wide with a finished floor elevation of 12 m (40 ft) and a full basement at elevation 7.5 m (24.5 ft). The historic building has a finished floor elevation of 13.7 m (45 ft) and its basement at elevation 10. 7 m (35.3 ft). It is supported on a 0.5 m (1.5 ft) thick rubble wall with a bottom at elevation 10.6 m (35.0 ft). The tower mat extends 36 ft (11 m) below grade or about 28 ft (8.S) below the existing historic build­ing, thereby requiring underpinning. When fully loaded, the settlement of the mat will cause the abut ting underpinning to also setUe, which would be detrimental to the historic building. Therefore, an innovative solution was necessary to isolate the underpinning from the stresses induced by the adjacent mat to safeguard the historic structure.

Jul 1, 2024

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By Satyajit Vaidya, Rudolph Frizzi, Quadri Owokoniran

"This paper presents a case history in the design and construction of high-capacity drilled shafts for the iconic New York Wheel presently being constructed along the St. George area waterfront in northern Staten Island, New York. Although the site is located in an area that offers views of the Statue of Liberty, the Manhattan skyline, and New York Harbor, the variable and challenging subsurface conditions at the site and the structural loading requirements for Wheel erection and service conditions presented geotechnical design and construction challenges. The paper focuses on site and subsurface conditions, drilled shaft design and construction details, results of Osterberg-cell and lateral load testing, and load test data analysis and evaluation.PROJECT DESCRIPTIONThe proposed 630-foot (190 m) -tall New York Wheel (the Wheel) is projected to be one of the tallest observation wheels in the world. Upon completion, the Wheel will be capable of carrying over 1,400 passengers in its 36 capsules. The Wheel site is located along New York Harbor offering views of the Statue of Liberty, the Manhattan skyline, and the New York Harbor; see Fig. 1. The Wheel structure is sited along the waterfront, and served by a 3-story terminal located south of the Wheel in the eastern portion of the site and having a footprint area of about 34,250 sq-ft (3,180 sq-m). A 4-story parking Garage, with a footprint of about 112,840 sq-ft (10,480 sqm), is to be constructed south of the Wheel in the central and western portions of the site.SITE AND SUBSURFACE CONDITIONSThe site’s close proximity to the New York Harbor presented geotechnical challenges because the site is located in an area that was once beyond the historic shoreline of Staten Island. The site is an about 350,000-sq-ft (32,500-sq-m) parcel generally bounded by the Richmond County Bank Ballpark to the southeast, the 9-11 Memorial to the east, Bank Street to the north and northeast, and Richmond Terrace and an associated retaining wall to the southwest and south. A 50-ft (15-m) -wide New York City Transit Easement, with an active on-grade service area and tracks, is located in the southern portion of the site. See Fig. 2 for site location and approximate location of the Wheel foundation footprint."

Jan 1, 2016

Jan 1, 2003

By Satyajit Vaidya, Rudolph Frizzi, Sandy Larimer

"This paper presents a case history in design and construction of a deep foundation system that included high-capacity open-ended driven piles constructed to support a high-rise building in Manhattan, New York. The project site is bordered by existing buildings, active streets, and critical public transportation infrastructure, which were considered in the new building’s deep foundation and seismic design. This paper focuses on driven pile foundation design and installation through relatively loose soil deposits. Unique design aspects included seismic design considerations, and pile splice design for open-ended steel pipe piles subject to significant uplift and lateral loading. Unique construction aspects included quality assurance of open-ended steel pipe pile splices, and uplift and lateral load testing of driven piles installed in close proximity to other foundation elements installed for the project.SITE CONDITIONS AND SUBSURFACE CONDITIONSThe project site is located in Manhattan, New York, and is bordered by existing buildings, active streets, and critical public transportation infrastructure that is located about 60 feet from the site. The existing sidewalk grades around the site are between about el 4 and about el 13; elevations are referenced to the North American Vertical Datum 1988 (NAVD88).Subsurface conditions at the site generally consist of successive strata of historic fill, former river bottom deposits consisting of compressible clayey soils, and medium dense to dense sand, overlying mica schist bedrock. A generalized subsurface profile is shown in Fig. 1. The historic fill stratum is about 10 to 45 feet thick, and generally consists of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick, concrete, and glass fragments. The underlying former river bottom deposit stratum is up to about 15 to 20 feet thick, and generally consists of very soft to very stiff clay and lenses of very loose to loose sand. Medium dense to dense sand was generally observed below the historic fill and former river bottom deposit strata and overlying bedrock. Top of bedrock was generally observed at about 80 to 105 feet (i.e. at about el -75 to el -100), except in the southeastern portion of the site where the top of rock was observed as deep as about 140 feet (i.e., at about el -135). Groundwater levels typically ranged between about el 1.5 and el -0.5."

Jan 1, 2016

By E. Naesgaard, Brian E. Hall, A. Amini, Advanced Geosolutions, A. Azizian

"A 2 km section of the Evergreen Line Rapid Transit Project is supported on improved ground consisting of cement deep soil mix (CDSM) panels because of highly variable and challenging soil conditions, especially the potential for seismic liquefaction-induced lateral spreading. CDSM was used as an alternative approach in place of driven piles for reducing the seismic lateral spreading displacements. An additional significant aspect of obtaining owner acceptance for CDSM was demonstrating that both seismic and non-seismic performance would equal or exceed that of using driven piles. It was recognized that, to demonstrate adherence to the seismic performance requirements, seismic design should be based on dynamic analyses (using FLAC) to estimate likely displacements and stresses/strains in the CDSM panels. One focus of the analyses was investigating the potential for cracking of the CDSM panels and the resulting displacements. This was simulated using the Ubiquitous-Joint and UBCSAND constitutive models.INTRODUCTIONThe Evergreen Line Rapid Transit Project (ELRT) is an 11 km extension of the SkyTrain system through Burnaby, Coquitlam and Port Moody in the Lower Mainland of British Columbia, Canada (Figure 1). The ELRT project is being delivered through a Design/Build/Finance model by Evergreen Rapid Transit Construction (EGRT), an SNC-Lavalin Inc. company, to the Province of British Columbia (the Province).This paper discusses the ground improvement design for a 2 km section of the alignment through Port Moody, a historic city at the head of Burrard Inlet. The alignment is located in a right-of-way of restricted width with many pinch points close to residential and commercial properties, and directly adjacent to the Canadian Pacific Railway (CPR) mainline tracks. The ground slopes from south to north across the alignment towards Burrard Inlet at inclinations of up to about 6%. Design and construction of the Port Moody section was subcontracted to SNC-Lavalin Constructors (Western) Inc. (SLCW) and SNCLavalin/ Graham Construction Joint Venture (SGJV). Construction included single- and double-track slab guideways, pocket track (where up to four to six tracks were present), and Moody Centre Station."

Jan 1, 2015

By Harry Schnabel, Mitchell L. Fong, Douglas R. Jenevein, Thomas S. Lee

"The Warm Springs Extension (WSX) is one of a series of projects that will eventually extend the Bay Area Rapid Transit System (BART) from Fremont to San Jose, California. A cut and cover tunnel was used for a portion of the extension that runs through Fremont Central Park to minimize the impacts that an at-grade railway would have on the Park. A cement deep soil mix (CDSM) wall was selected by the engineer as the preferred method of providing structural support and groundwater cut-off for a portion of the tunnel where it passes through an important aquifer and near Lake Elizabeth. In addition to the CDSM wall, a jet grout plug was constructed at the base of the tunnel to provide a complete groundwater cut-off.This paper will discuss the unique quality assurance and quality control measures taken for the soil mix wall and jet grout plug as well as the methods used to repair leaks and mitigate water seepage through the exposed wall and grout plug.PROJECT DESCRIPTIONThe Bay Area Rapid Transit (BART) Warm Springs Extension (WSX) project is located south of the existing Fremont BART station extending 8.9-km (5.4 miles) to Warm Springs District in Fremont, California. The WSX project has been divided into two contracts with different delivery methods. In order to minimize impacts to Fremont Central Park, a subway was selected at this portion of the alignment under a conventional design/bid/build contract.The Fremont Central Park Subway (FCPS) which begins on the south side of Walnut Ave and ends just north of Paseo Padre Parkway and is about 2.3-km (1.4 miles) long. Fig. 1 shows the entire WSX and the FCPS project. The FCPS contract consists of a cut-and-cover subway box, subway transition structures, ventilation structures and a section of which transverses Lake Elizabeth (a man-made lake). The geologic conditions consist of fill (sand, silt, clay and construction debris), Young Alluvium (clay and silt), Basin Deposits (clay, silt, and sand), and Older Alluvium (sand and gravel) as shown in Fig. 2.HYDROGEOLOGY OF THE PROJECT SITEThe FCPS is dominated by two geologic features - the Hayward Fault and the Above Hayward Fault (AHF) aquifer. The AHF aquifer provides a significant source and storage of water for the local water district. The underground subway will penetrate this aquifer and is up to 11m (36 ft) below the groundwater table. No groundwater was allowed to be pumped during construction of the subway box by Alameda County Water District (ACWD). To facilitate excavation for the subway box, temporary cut-off walls and a grout plug were designed to retain and resist high differential hydraulic pressure. The following section describes the selection of a deep soil mixing method for water cutoff. Design of the grout plug has been described in Lee, et al., 2011 and Fong and Lee, 2009, and is not the focus of this paper."

Jan 1, 2015

By James G. Ulinski, Sebastian Lobo-Guerrero, Vishal B. Patel

"Recently modified design equations used in the transportation industry to calculate side friction and end bearing capacity for drilled shafts are now providing more realistic estimations of capacities than did previous methods. Using multiple case studies and test results from various projects, a more realistic design approach was formulated by the Federal Highway Administration (FHWA), which resulted in greater values of ultimate capacity for side friction and end bearing and in a more efficient design overall.In 2010, the FHWA published GEC-10 – Drilled Shafts: Construction Procedures and LRFD Design Methods, which illustrates a different method of calculating side friction and end bearing resistance and results in greater values for design. In 2014, the Association of State Highway and Transportation Officials (AASHTO) adopted the method put forth by FHWA, which was included in its LRFD Bridge Design th Specifications, 7 Edition. The Pennsylvania Department of Transportation (PennDOT) recently adopted and incorporated the similar methodology as AASHTO for calculating side friction and end bearing for drilled shafts in rock, and these changes are reflected in the 2015 edition of the PennDOT Design Manual, Part 4 (DM-4). This article discusses the past and current design methodology along with a project case study with results from Osterberg Cell (O-cell) load testing, which presents a comparison between the design resistances of ultimate side friction and end bearing and the measured capacities at failure.The Old and the NewEditions of the AASHTO LRFD Bridge Design Manual from 2012 and earlier estimated ultimate side resistance, qs, in rock using the following equation (modified from Horvath and Kenney, 1979):qs=0.65aEpa(qu/pa)0.5 < 7.8pa(f ’c/pa)0.5 where: qu is the uniaxial compressive strength of the rock in ksf; pa is the atmospheric pressure in ksf; aE is the reduction factor to account for jointing in rock; and f ’c is the compressive strength of the concrete in ksi. For intact rock, previous versions of the AASHTO manual required that the ultimate end bearing resistance, qp, was calculated using the following equation: qp=2.5qu."

Jan 1, 2017

By Rendon Rieth, John Bryant, Kourosh Tamizdoust, Amr Helal

Expansive soils are widespread in the Southern, Western, and Rocky Mountain areas of the United States. Expansive natural clays and bedrock can expand upon wetting and shrink upon drying. These soils can cause damage to structures, roadways, and pipelines. Accurate estimation of volumetric deformation of expansive soils is critical to minimizing damage to the nation’s infrastructure. Free-field heave is the amount of movement the ground subsurface experiences due to wetting/drying of the soils within the active zone, with no surface surcharge load (e.g., foundation load) applied. Active zone is the depth below the ground where the soil volume deformation can still occur due to moisture/energy changes in unsaturated soils. Several methods for free-field heave estimation have been developed over the years including empirical methods and using oedometer swell test results and soil suction values. Further, in the past decade, most numerical studies have been performed to determine the free-field heave by incorporating hydro-mechanical framework which disregards the temperature effect and usually considers one-way coupling between the moisture flow and swelling/shrinkage deformation. The main objective of the current study is utilizing a strongly coupled thermo-hydro-mechanical (THM) model for the estimation of active zone depth and free-field heave when the soil is subjected to real-time climate conditions. The THM model, input thermal, and hydraulic/mechanical data are implemented in COMSOL Multiphysics software. The results are compared with experimental data from a case study in the Colorado Front Range area. The Soil-Water Characteristic Curve (SWCC) and Hydraulic Conductivity Function (HCF) are based on the Van Genuchten (VG) model and the mechanical constitutive model, which governs swelling deformation, is based on the Extended Barcelona Model. The THM model predicts the active zone reasonably well. Moreover, the simulation of free-field heave is compared with the analytical calculation produced by VOLFLO software.

Oct 31, 2023

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Joe Smith, Roberto Rodriguez, Francisco Ciruela-Ochoa

Drilled-In Displacement Piles (DDPs) present some advantages over other deep foundation solutions making them suitable for challenging conditions encountered at John F. Kennedy (JFK) International Airport Headhouse Expansion Project. For one, elevated railway tracks required the installation to occur with as little as 12 ft of clearance. Secondly, their ease of installation and overall material requirements deemed them more efficient than traditional micropiles from a schedule and cost point of view. Lastly, the low vibrations induced by DDPs to the surrounding sensitive structures were crucial for an operational airport. All combined contributed to the final decision of recommending this foundation system for the Project. This paper documents the use of DDPs for the Project and documents the design and specification process along with load testing program results and observations made during the construction of production elements from a case history perspective.

Oct 31, 2023

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By Marco D. Boscardin, Kenneth A. Pidgeon, Adriane G. Boscardin

"Hollow bar tiebacks can offer an economical alternative to conventional solid bar and strand tieback systems for use in temporary excavation support construction. However, the limitations associated with the installation of hollow bar tiebacks require special attention during design, construction and load testing to verify conformance with conventional performance and proof testing criteria (PTI, 2014). In particular, providing a reliable free length is complicated by the 10-foot (3-m) -long, segmental, couplingto- coupling nature of the free length sheath in the hollow bar system, and addressing the fully grouted annulus of the bond zone and the free length zone at the end of installation are key concerns. In addition, it is often more convenient to install a greater number of more closely spaced, lower capacity tiebacks with the hollow bar system, compared to conventional tiebacks. This paper examines how these issues were addressed for a project involving a 60-foot (18-m) -deep sheet pile excavation through a highway embankment and a 70-foot-deep sheet pile and soldier pile and lagging excavation through a railroad embankment, both supported by a hybrid system of hollow bar tiebacks and hollow bar soil nails. The project involved approximately 300 tiebacks and 400 soil nails.INTRODUCTIONEngineers Construction, Inc. (ECI), constructed a pair of 32-foot (9.8-m) -wide (clear span), 30-foot (9- m) -high (21 feet (6.4 m) above the stream bed), cast-in-place concrete arch culverts as a design-build project for the Vermont Agency of Transportation (VTrans) in East Ryegate, Vermont. The new culverts replaced an existing 8-foot (2.4-m) -wide by 6-foot (1.8-m) -high cast-in-place concrete culvert under US Route 5 (RTE5), and twin, 2-foot (0.6-m) -wide by 5-foot (1.5-m) -high granite block culverts under the Washington County Railroad (WACR) alignment. The culverts convey Manchester Brook eastward, through the embankments for RTE5 and the WACR, on its way to the Connecticut River. The Connecticut River is located approximately 100 feet (30 m) east of the WACR embankment. The existing structures were undersized and backed up water behind the embankments during high flow events; and often trapped debris that flowed down the brook and became clogged. The existing culverts also had cracks and openings that have resulted in the loss of ground into the culverts and the formation of sinkholes in the sides of the embankments. Moreover, the reason for the large cross-sectional dimensions of the culverts was to make them of sufficient size and openness to encourage the migration of fish up the stream to spawn. The culvert through the RTE5 embankment is 144 feet (44 m) long, and the culvert through the WACR embankment is 128 feet (39 m) long, with a 57-foot (17.4-m) -long by 32–foot (9.8- m) -wide by 17-foot (5.2-m) -deep 10 feet (3 m) deep above the stream bed) open channel section between the two culverts. A plan view of the culvert alignment is presented in Figure 1."

Jan 1, 2016

By Francisco A. Flores, José L. Aguirre, Héctor A. de la Fuente, Erika Bernal, Jorge Arroyo-Esquedla

This paper presents the analysis, design, and construction of soil improvement for storage tanks foundation support at a site in Tabasco, Mexico. A total of 980 Rammed Aggregate Piers of 12.5 m in length and 0.5 m in diameter were designed and constructed to support four storage tanks. The soil conditions at the site generally consist of loose to medium dense silty/clayey sand to about 8m depth, underlain by very loose to medium dense silty/clayey sand with seams of very soft clay. The use of Rammed Aggregate Piers induced densification of the soil to increase its stiffness and reduce the liquefaction potential to control both static and dynamic induced settlements. Standard Penetration Test (SPT) and Cone Penetration Test (CPTu) explorations were performed prior to and post soil improvement to compare the liquefaction potential and the Factors of Safety associated with the two conditions. Finally, the soil improvement installation rate is presented. Soil improvement using Rammed Aggregate Piers represented a suitable alternative to support storage tanks foundation in potentially liquefiable areas.

Oct 1, 2022

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Ronaldo Luna, Donald Deardorff

"The use of load and resistance factor design (LRFD) is well documented since the 1960s for structural applications when it was first adopted into the American Concrete Institute Building Code in 1963 and was established for geotechnical applications by the Danish Geotechnical Institute about the same time under the name of Limit State Design (LSD).The Federal Highway Administration required all federally funded projects to use the LRFD method by 2007. Due to this funding requirement, recent LRFD research for geotechnical applications has focused on common bridge foundations (i.e., driven or drilled shafts), resulting in good documentation for design using these methods. Unfortunately, the practicing geotechnical engineer does not intuitively know how to create resistance factors for deep foundations systems that have design methodologies and installation techniques significantly different from driven or drilled shaft foundation systems.Helical anchors typically use semiempirical methods for preliminary capacity design and a torque correlation methodology during installation to verify required capacity. Here we provide basic information on the LRFD methodology for helical anchor design. Additionally, the First- Order Second Moment (FOSM) method is applied to a previous helical anchor study (Hoyt and Clemence 1989) to determine resistance factors for an ultimate tension capacity strength limit state.MethodologyThe concept of the LRFD method is to establish factors for both the load and resistance that account for uncertainties using probability theory. The factors increase the nominal load and/or decrease the nominal resistance such that the probability of failure is an acceptable value. LRFD also accounts for the effects of load combinations (dead, live, seismic, wind, etc.) by determining the probability of the combined occurrence. The general form of the LRFD equation used by American Association of State Highway and Transportation Officials (AASHTO) is:"

Jan 1, 2009

By Martin Walker, Joseph Ang, Jongwon Lee, Alvin Bayudanto, Lilian Lorincz, Morteza Khorshidi, Wenyong Rong

This paper presents a case history of liquefaction susceptibility evaluation study for a major infrastructure project in the San José area. The subsurface material of the study area consists of Holocene alluvial deposits composed of interbedded and crosscut clays and silts, sands and gravels. The simplified approach for liquefaction triggering evaluation was carried out using both CPT data and SPT data representing site’s seismic capacity and the peak ground acceleration associated with a return period of 975 years at ground surface representing seismic demands. Site-specific cyclic stress ratio (CSR) profiles as seismic demand are also estimated from one-dimensional site response analysis. The simplified approach uses empirical depth stress reduction factors (rd) based on generic shear wave velocity profiles to account for the non-rigid response of the soil profile in estimating CSR. The CSR profiles of the simplified procedure were examined by completing site response analyses using site-specific soil profiles to represent site-specific seismic demands in the liquefaction triggering evaluation. The paper concludes with a comparison and discussion of the liquefaction evaluation examining results from CPT versus SPT data, and the comparison of CSR profiles from the simplified procedure versus site-specific response analysis.

Sep 8, 2021

By Shigenori Horikawa, Nobutaka Tanaka, Toshiro Hara, Kengo Yamamoto

"The CDM-LODIC method(Low Displacement and Control method), a modified the CDM(Cement Deep Mixing) method, reduces the ground displacement through the removal of in-situ soil equivalent to the amount of slurry injection using the continuous auger flight attached on the shaft above the conventional the CDM mixing tool. The reduction of ground displacement minimizes the impact on adjacent buildings and other infrastructures. Since the development of the CDM-LODIC in 1985, this method has been used for more than 900 projects with total volume of improved soils exceeding 5.3 million yd3 (7 million m3). The ground displacement that could be caused by deep soil mixing is controlled by balancing the volume of discharged soil and the volume of slurry injected for soil mixing. This paper presents the ground improvement work for the Sanriku Coast Expressway Project using the CDM-LODIC method to 1) control the ground displacement during ground improvement to minimize the impact to existing buildings and facilities and 2) utilize low height CDM-LODIC equipment to avoid potential damage to critical facilities in the vicinity of ground improvement area and avoid interference on the normal operation of the Ishinomaki Red Cross Hospital.INTRODUCTIONSanriku Coast Expressway is a reconstructed highway, which is part of an early restoration program to recover from the Eastern Japan Earthquake of March 11, 2011. This highway extends 223 mile (359 km) and connects the Pacific Coast regions of three prefecture of North Eastern Japan as shown in Figure 1. Along a section between Yamoto - Ishinomaki road, the highway was expanded from two lanes to four lanes to mitigate traffic congestion for the adjacent city center and hospital and to serve as an efficient transportation route for emergency or disaster relief needs as shown in Figure 2. Deep mixing ground improvement with an area replacement ratio of 50% was designed to provide settlement control under the new fill embankment of the expanded highway as shown in Figure 3. The original CDM treatment layout using 5.2ft (1.6 m) diameter columns is shown in Figure 4."

Jan 1, 2015