Search Documents

By Brian McGlynn

There are many factors that can result in a site characterization being limited. For example, a client may undervalue the importance of a good geotechnical report, or an owner may feel that it would take too much time to perform an appropriate investigation among other reasons. For this project, neither was the case. The challenge was that the construction sequence of work required wick drains to accelerate the settlement of soil that had yet to be placed, resulting in the need to create a wick drain bid package based on unknown settlement parameters. This wick drain project took place in Long Beach, California, at the Long Beach Middle Harbor Re- development. For much of the past decade, the Port of Long Beach undertook a $1.5 billion redevelopment of two outdated terminals to create the Long Beach Container Terminal (LBCT). To achieve this goal, the existing terminals were demolished and the slip that serviced one of the older terminals was designed to be infilled to create the new area that would allow for the LBCT to manage 3.3 million TEUS (a commonly used freight term meaning twenty-foot equivalent unit) of cargo each year. Ultimately, the construction of the LBCT would be performed under multiple contracts to allow the new terminal to begin operation in a phased approach. Menard performed the wick drain installation under two out of three contracts, and this case history focuses on the challenges anticipated and faced under the second of these awarded contracts.

May 1, 2023

By Armin W. Stuedlein, Steven R. Saye

The differences between calculated axial pile capacity and the capacity realized during and following installation has long presented a significant concern for foundation engineers and contractors. Such differences have increased in prevalence with the increased use of larger diameter steel pipe piles and the significant increase in design-build contracting. The writers present concepts to close the gap between calculated axial pile capacity and the capacity realized during and following installation of driven pile foundations, including: (1) pile set-up in plastic soils, (2) limitation of re-driving of piles after setup which serves to reduce pile capacity, (3) the use of a vibratory hammer to install piles in cohesive soils disturbs the supporting soils and reduces the pile side resistance capacity significantly, and (4) long pile installation times for open-ended piles can damage the pile side resistance. Examples are presented from practice to illustrate these concepts and to guide pile installation planning to recognize the installation impacts and either consider alternate installation approaches or to properly consider the installation impacts during design.

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008

By Brenton Cook, Daniel Mageau, Larry Applegate, Aaron McCain

"Ground freezing was successfully used to create an impermeable barrier wall along 3,000 feet of the downtown Seattle waterfront as part of the Seattle Seawall Replacement Project. This $360 million re-development involved removing the original 1930-era seawall and replacing it with a new, seismically resistant concrete wall supported on fill soil improved by jet-grout. The replacement wall was one of the largest construction projects in the state of Washington at the time. Ground freezing is typically used as both a structural shoring wall and groundwater cutoff. However, at this project it was used primarily as a cutoff wall to stop groundwater seepage into the 16-foot deep excavation from the landside areas.The project was divided into ten boxes (sections), each typically 200 to 600 feet in length. Only a few boxes were under construction at one time to reduce the impact on tourist-dependent local businesses. Soil conditions in the freeze zone consisted of sand, gravel and silt fill with abundant wood and debris. Tidally influenced groundwater, much of it contaminated, was difficult and expensive to control using wells during initial stages of construction. For all subsequent stages, a frozen soil wall extending to about 35 feet in depth was used to stop groundwater seepage into the excavation. An additional benefit of ground freezing included elimination of potential settlement beneath nearby buildings, utilities, and the Alaskan Way Viaduct that would likely have occurred with the use of conventional dewatering wells. The frozen soil wall crossed more than 130 buried utility locations (including water, sewer, storm, electrical, fiber optic, phone, gas, steam) with no damage. The frozen soil wall was very successful and limited groundwater influx from the landside to the seawall excavation to a negligible amount so that pumping, storage and treatment of contaminated groundwater was essentially eliminated."

Jan 1, 2016

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By Jeremiah M. Jezerski, Russell H. Lutch

The Mount Olivet Road Drop Shaft (MOR-DS) support of excavation (SOE) is a circular unreinforced concrete shaft with an inside diameter of a 30.5 ft (9.3 m) and depth of 120.5 ft (36.7 m), constructed using slurry wall methods. The SOE for the adjacent Mount Olivet Road Approach Channel (MOR-AC) and Mount Olivet Road Ventilation Vault (MOR-VV) near surface structures (NSS) consists of lean mix concrete walls and cement-bentonite walls, respectively, both constructed using slurry wall techniques and reinforced with embedded soldier piles. NSS SOE required multiple levels of preloaded internal bracing, with excavation depths of up to 75 ft (22.9 m). The original design construction sequence for the shaft and NSS SOE required that the MOR-DS be constructed in its entirety and backfilled to ground surface prior to excavation of the adjacent NSS SOE. After installation of the drop shaft and NSS SOE an accelerated construction sequence was implemented requiring the analysis of the excavation support systems to determine if the excavations could be open concurrently without adversely impacting the partially constructed permanent MOR-DS structure. The MOR-DS was analyzed using the finite element analysis (FEA) software, MIDAS GTS, to demonstrate that the unbalanced loads applied to the MOR-DS composite structure due to the revised sequence would not exceed the strength and serviceability requirements per ACI-350 or superseded by the more stringent project requirements. The results of the FEA were used to set limits for geotechnical instrumentation consisting of strain gauges located on the brace levels of the NSS SOE. A comparison of the SOE design hand calculations, FEA model results and instrumentation data is presented.

Oct 1, 2022

By David S. Graham, Paul J. Axtell

Crosshole Sonic Logging (CSL) non-destructive integrity testing identified anomalous readings near the base of a 6.5-foot diameter drilled shaft rock socket. The anomaly was confirmed to be a defect by subsequent coring and core hole camera inspection. A large void and exposed rebar were visually observed in one of the core hole camera inspections. The center of the shaft was then excavated initially with 3-foot diameter tooling and subsequently with 4-foot diameter tooling as part of the remedial actions to address the defect. While excavating with 3-foot diameter tooling, the shaft defect was not encountered. Excavation with 4-foot diameter tooling revealed the defect, a significant void around the majority of the shaft circumference. The void extended radially from the circumference of the 4-foot diameter excavation to beyond the reinforcement cage to the exposed wall of the rock socket around approximately 80 percent of the shaft circumference. CSL results and observations made during remedial shaft investigation and excavation are in good agreement. The shaft defect, located primarily outside of the reinforcement cage, was effectively identified by CSL testing. Although the defect was confirmed by investigative coring, the remedial excavation demonstrates how the investigative coring could have easily missed the defect. This paper shows how CSL results compare to physical observations made during a rare opportunity to characterize the full extent and nature of a drilled shaft defect originally identified as an anomaly by CSL testing. INTRODUCTION The case history presented here pertains to a drilled shaft for a multi-shaft bridge pier in the Midwestern United States. However, the observations presented in this paper are not a result of unique site conditions or the particulars of the project. The lessons learned from this case history are applicable to almost any drilled shaft constructed in the wet. The overall length of the subject shaft is 22 feet including approximately 12 feet of permanently cased, 7-foot diameter shaft extending to bedrock and approximately 10 feet of uncased, 6.5-foot diameter rock socket. The shaft is designed to resist axial and lateral loads and considers the contributions of side and base resistance in the axial design. Six, 2-inch diameter steel Crosshole Sonic Logging (CSL) tubes are include in the shaft. The bedrock at the shaft location includes beds of sandstone, shale, and limestone. The shaft was drilled using conventional drilling equipment and tooling, and water was used as the drilling fluid. Conventional drilled shaft concrete appropriate for underwater tremie-placement was placed via a 10-inch diameter open hopper tremie.

Jan 1, 2019

By Martin B. Hudson, Kenneth S. Hudson, Gwendolyn Arreguin

A twin high-rise project site in Century City posed several foundation engineering challenges for the design team. One portion of the twin high-rise project site was required to utilize top-down construction in order to allow a driveway to remain open during construction of the project’s 40-foot deep excavation. The challenge was compounded by the need to utilize a mat foundation to support the high-rise construction and yet have temporary drilled shafts through the mat foundation area that would not create excessive differential settlement. This was accomplished by constructing a deck supported by eight drilled end- bearing drilled shafts with Osterberg load cells and five 7-foot-diameter end-bearing drilled shafts. The Osterberg load cells served to verify the capacity of each of the drilled shafts and preload the soils at the drilled shaft tips. The 7-foot-diameter shafts were constructed with bond breakers to prevent skin friction but instead mobilize end bearing (for settlement compatibility with the surrounding mat foundation). After the drilled shafts were placed, then top-down construction began beneath the driveway, leaving the driveway supported on the drilled shafts. Construction challenges included drilling of the shafts through previously abandoned tieback anchors from an adjacent parking structure basement, as well as cemented layers within the rock materials. The paper describes the use of the various analytical methods used to calculate capacities and check settlement compatibility, the construction and testing methods utilized, and the construction challenges encountered. INTRODUCTION Wood Environment and Infrastructure Solutions, Inc. (hereafter referred to as Wood) performed a geotechnical investigation for the New Century Plaza currently being constructed in the Century City District of Los Angeles, California. The New Century Plaza project consists of the construction of two new towers (designated as North and South Buildings) and the rehabilitation of the existing Hyatt Regency Century Plaza Hotel. The existing hotel tower is 15 stories in height above the existing grade and is underlain by four subterranean basement parking levels. The new North and South Buildings will stand approximately 46 stories in height above the existing grade to accommodate residential use. The new towers are planned west of the existing hotel. The site was previously occupied by the existing hotel subterranean parking structure and overlying podium structure, and a loading dock in the southwest portion of the site. The former western portion of the podium and subterranean parking structure west of the existing hotel building western edge were demolished to allow for new subterranean levels, a new podium structure, and the new towers. The lowest floor of the proposed subterranean level required excavation on the order of 35 to 80 feet.

Jan 1, 2019

By Gerry Houlahan

"The 2015 Outstanding Project Award (OPA), which recognizes the superior work of DFI members, was awarded for the San Francisco- Oakland Bay Bridge New East Span. The award was presented to representatives from Caltrans and the T.Y. Lin International/Moffatt & Nichol Joint Venture at the DFI 40th Annual Conference on Deep Foundations in Oakland, Calif. A committee selected this project based on size, scope and challenges of the project; degree of innovation and ingenuity exercised; and the uniqueness of the solution to the difficulties of the job. A bridge across the bay between San Francisco and Oakland was proposed as early as 1872, but it took until November 12, 1936, until it became a reality. The bridge spans to the west of Yerba Buena Island were conventional suspension spans, while the east spans used a steel cantilever truss design and simple steel truss spans. This double-deck bridge served the Bay Area well until 1989. In that year, the magnitude 7.1 Loma Prieta earthquake damaged the East Span of the San Francisco-Oakland Bay Bridge. The resulting interruption to service across the bay demonstrated the vital role this bridge plays in the economic and life safety activities of the Bay Area. The project owner, California Department of Transportation (Caltrans), determined that the safest, most cost-effective solution was a total bridge replacement. The Engineer-of-Record, T.Y. Lin International/ Moffatt & Nichol Joint Venture, working closely with Caltrans, the Metropolitan Transportation Commission (MTC) and the California Transportation Commission (CTC), was charged with developing a comprehensive design strategy that met the project’s stringent criteria for seismic safety. These criteria included the new bridge’s designation as a regional Lifeline Structure that must open to emergency traffic shortly after the occurrence of a 1,500-year return period earthquake"

Jan 1, 2015

By Ali Ebrahimi, Meena L. Viswanath, John F. Beech, Mustafa B. Erten, Ming Zhu

"Excessive deformation of a cantilever sheetpile wall can occur due to dredging, excavation, backfilling, or long-term creep behavior of soil. A buttressing berm constructed in front of the wall can be considered as a mitigation technique to prevent or decrease the deformation by increasing the passive earth pressure and thus improving the wall stability. The effect of the buttressing berm on the stability and deformation of a sheetpile depends on the berm geometry (i.e., the thickness/depth and the width) as well as the properties of the sheetpile and the adjacent soils. A parametric study was conducted using a conventional limit equilibrium method. Design charts were prepared to evaluate the effect of a buttressing berm and the soil friction angle on the wall stability and deformation. These charts can be used as a tool by geotechnical engineers to make a quick estimate of the required size of a buttressing berm in case of calculated or unexpected excessive deformation of a sheetpile. An analysis of the effect of a buttressing berm on the stresses and deformation of a sheetpile was also compared with the results from finite element analysis. The results of this comparison are discussed.INTRODUCTIONCantilever sheetpile walls are commonly used to support excavations. Sheetpiles are hot rolled or cold formed sections of steel made to interlock with adjacent sections to form a continuous structure providing lateral support. Sheetpile walls can be cantilever walls or anchored with tiebacks. To construct a cantilever sheetpile wall, sheetpiles are driven by pile drivers or vibrated in to a design depth sufficiently below the depth of excavation. Excavation can then proceed in front of the sheetpile wall, which resists the earth pressure loading from behind the wall. The design depth and geometry of the sheetpile wall depend on the soil conditions, the depth of excavation, and the tolerable deformation. In certain cases, when a small buttress of soil can be left immediately adjacent to the sheetpile wall, the required depth or geometry of the sheetpile wall can be reduced or adjusted, which can significantly decrease the cost of procuring and installing the wall. Such a buttress can also serve as a short-term or long-term remedy in case of observed excessive deformation in a constructed wall. Traditional methods of analyzing the stability of a sheetpile wall do not account for the passive pressure effects of this small buttress. In this paper, a parametric study was performed for a variety of soil types and wall and buttress geometries by implementing traditional limit equilibrium methods in commercial software and design charts were created illustrating the effect of a buttressing berm on sheetpile deflection. Selected cases were then modeled in a finite element software to compare the results with the traditional limit equilibrium method. The resulting design charts can be used as a tool by geotechnical engineers looking to reduce the design geometry of a sheetpile wall or address observed excessive deformation in a constructed sheetpile wall."

Jan 1, 2016

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By Nick Benedetto, Sonia Sorabella Swift, Taylor Towle, Seth Pearlman, Andy Sullivan

The Route 1&9T/New Road project is a three-part program to relieve the notoriously congested Route 1&9 (Tonelle Avenue) in the heart of the industrial sector of Jersey City, New Jersey. Contract 1 consisted of con­structing a new road over a 1 mi (1.6 km) Long stretch of unimproved land serving as part of the parking lot to a large postal facility. To get to grade, modular gravity retaining walls were specified on either side of the 54 ft (16.5 m) wide roadway corridor. While the proposed wall heights ranged from only 2-8 ft (0.6-2.4 m), the soils present on-site were not even suitable for a shallow embankment. The underlying soils were mixed fills and organic peat, underlain by soft clay and silt to depths ofupto 75 ft (23 m). The proposed solution presented in the project plans certainly would have worked on paper; however, Menard, having had poor experiences with rigid inclusion installation and load transfer platform (LTP) compaction at or just above the groundwater table, recog­nized the potential difficulties, delays and rework that would likely be required during construction of what was shown on the contract plans. As such, it proposed a value-engineered solution that resulted in a vast improve­ment in the constructability, perfor­mance and overall cost of the system. However, the benefits of this solution were not appreciated by the owner and the solution was met with high levels of scrutiny, perhaps because it differed from what was shown on the contract plans. The level of testing required of the solution was far greater than what was required of the design shown on the contract plans. Such rigorous and unwarranted confirmation of a value­engineered solution consumed time, money and resources that could be better used elsewhere. Instead, these designs should be compared to the design in the original contract plans based on technical merit and expected long-term behavior. This article walks through the design and construction process for the value-engineered solu­tion and highlights the many challenges experienced by the contractor to get final approval of the work perormed. Though the COVID-19 Pandemic was an unanticipated complication, the per­ceived distrust of the contractor's proposals and work was a barrier to progress that the authors hope will not exist in the future.

Feb 1, 2024

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By Graeme Smart, Thomas Fiala

"Yorkville Plaza II, a 40-storey signature condominium residence, is scheduled to open on Avenue Road in Toronto’s prestigious Bloor-Yorkville neighbourhood in spring 2017. In close proximity to Toronto’s subway system, the new tower requires six levels of underground parking, founded in wet, silty sand.Isherwood Geostructural Engineers (Isherwood) was retained in April 2012 by developer Camrost-Felcorp to provide a shoring and excavation solution to address the challenging site conditions. A 31-storey upscale residential building under renovation with three levels of parking, owned by Camrost-Felcorp, flanks the site on the north. Situated on the eastern border is a 7-storey building with three levels of parking. Avenue Road, a four-lane arterial road that brings heavy commuter traffic into downtown Toronto, runs along the western border, and on the southern border of the site is a busy City road that brings traffic into the popular Yorkville area. The tunnel for the Toronto Transit Commission’s (TTC) overburdened east-west subway is located 14.5 m to the south, running below an existing 26-storey neighbouring building. Electrical and communication utilities (Bell) are closely located along the southern side. Non-documented existing excavation shoring, installed in the early 1970s, on the southern and western sides compounded the difficulties presented by the TTC tunnel.This paper presents the unique, non-conventional hybrid shoring solutions Isherwood developed to address the challenges presented by the site, as well as other complications that surfaced during the project: non-encroachment requirements (no tiebacks) beneath uncooperative neighbours, tight geometry to install shoring, and Toronto’s two coldest winters in decades.THE PROJECTBecause of circumstances associated with this site, for this project Isherwood designed two unique shoring walls which drew on their experience and expertise they had gained over the last 40 years. The following is the story of this site:Yorkville is an affluent neighbourhood in the heart of Toronto with a vibrant mix of high-rise towers, residential homes, tony restaurants and flagship shops. The development requires six levels of underground parking (a 20m deep excavation), with three levels undermining the high-rise buildings to the north and east and extending into wet, silty sand.Isherwood was retained in the spring of 2012 to design the excavation shoring. Isherwood’s scope also included field support, design, verification and monitoring. Finite Element Analysis was employed to confirm Isherwood’s design and anticipated movement of the south shoring wall and the TTC subway tunnel.The existing site was severed in two, with the proposed condominium tower slated for the southern portion. On the north half of the site stands a 31-storey building (Yorkville Plaza I at 21 Avenue Road), with three levels of underground parking, sitting on belled caissons which were one foot from the back of the proposed shoring wall so this would have to be considered in relation to the design and drilling methods. Constructed in the early 1970s, Yorkville Plaza I is currently being converted from the Four Seasons hotel to luxury condominiums by Camrost-Felcorp. To the east, directly adjacent to the proposed shoring, stands a 7-storey building (164 Cumberland Road) with three levels of parking, supported on spread footings founded on stiff clayey silt. The tunnel for the TTC’s busy east-west subway, a double box structure built by cut-and-cover in the 1960s, is located 14.5 m to the south, 9 m below grade, and running below an existing 26-storey building. Bell fibre optic communication cables and electrical lines, along with storm and sanitary sewers, are situated on the south and west sides of the site, leaving limited room to install shoring. Due to the heavy volume of commuter traffic on the four-lane arterial road (Avenue Road) to the west, site access and lane closure were not permitted here."

Jan 1, 2015