Search Documents

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"The valuable materials resulting from the processing of gold-bearing ores are often refractory to direct gold recovery through cyanidation. There are multiple methods for chemical liberation of gold prior to cyanidation such as pressure and biological oxidation as well as atmospheric oxidation which is typically used in combination with physical activation of material by ultrafine grinding such as the Albion ProcessTM. This paper will examine the data from process testworks carried out to estimate the efficiency of the Albion Process™ for the oxidation of materials with a wide composition range prior to cyanidation. The data will be compared to that obtained by direct cyanidation of the feed (without oxidation) and from the testing of pressure oxidation on the feed prior to cyanidation. Albion Process™ tests were conducted in Institute TOMS with participation of Glencore Technology Pty Ltd (Australia). Refractory concentrates obtained from the ores of several Russian and CIS deposits were used as feed for the testing. These concentrates were also subjected to a material composition study and testing using conventional recovery methods. The resulted test data make it possible to perform an integrated assessment of process properties for materials with different compositions, compare performance of various process flowsheets for the materials under study, and conclude on efficiency of Albion Process™ application for gold recovery from refractory materials different in their composition.INTRODUCTION It is often the case that gold ore concentrates are refractory to gold recovery by direct cyanidation. This refractory nature is as a rule attributable to fine gold dissemination in minerals, most often in pyrite and other sulphides, as well as to the increased amount of components impeding cyanide leaching of gold due to cyanide consumption and reducing process conditions. The refractoriness of the concentrates results in low gold recovery values when conventional cyanidation technology is used. In this context, various additional processes are applied to breakdown such refractory sulphide concentrates, i.e. mechanical breakdown (fine and ultrafine grinding), chemical breakdown (atmospheric oxidation, e.g. Leachox, acid-oxygen oxidation, pressure oxidation – POX, bacterial oxidation – BIOX), and thermochemical breakdown (various roasting methods). Such breakdown processes allow for increase in recovery of finely disseminated gold during the downstream cyanidation, however, their application is cost-intensive and does not always ensure economic benefit."

Jan 1, 2018

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By K. C. Corin, M. S. Manono, J. G. Wiese

"It has been suggested that hydroxo species, particularly those of calcium, selectively adsorb onto gangue minerals. Such species enhance the depressive action of carboxymethyl cellulose (CMC) onto gangue via an acid-base interaction between the positively charged mineral surface and the negatively charged CMC molecule. Thus, the hydrophilicity of gangue minerals is enhanced, preventing the dilution of the concentrate. However, as there is little evidence to support these claims it is important to investigate. Adsorption data and mineral surface charge analyses will allow a fundamental understanding into how electrolytes and their ionic strengths affect gangue-depressant adsorption. It is strongly anticipated that decoupling these effects will allow process operators to tailor their process water quality needs towards best flotation operating regimes and in the long run effect closed water circuits. Thus, using talc and pyrrhotite as proxies, this work investigates the influence of the ionic strength of process water on the adsorption of CMC onto minerals in sulphide flotation.INTRODUCTIONThe phenomenon of gangue depression in mineral flotation is of critical importance as regards the attainment of a required concentrate grade. This thus suggests that the depressant of choice has to have a highly selective affinity for the targeted gangue minerals. This would ensure the necessary prevention of gangue from reporting to the concentrate without inadvertently depressing the value bearing mineral. The chemistry of the environment regulates the manner in which gangue depression occurs. In sulphide flotation, polysaccharides are used as depressants of choice to depress naturally floatable gangue which may in the case of Merensky ores exist as talc. The two widely used polysaccharides in the South African context are carboxymethyl cellulose (CMC) and modified guar gum. It is suggested that polysaccharides depress gangue by rendering the surface of gangue hydrophilic or by preventing the formation of hydrophobic layers on gangue mineral surface, forming large gangue aggregates and thereby increasing their heterocoagulative nature (Shortridge et al., 1999)."

Jan 1, 2018

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. In Kure, a very fine grinding requirement for an adequate level of liberation makes a successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu Column flotation tests were conducted at the plant site using two different column types The experiments proved that the grade of the concentrate could be increased from about 14% Cu to 25-26% Cu. Murgul Cakmakkaya Copper Concentrator is the largest copper concentrator in Turkey. Although concentrate production capacity is around 170,000 tons annually with 22-23% Cu content, this figure tends to be much lower than that. In Murgul a Turbo Column of Multotec Company of South Africa was employed. As a result of systematic column flotation tests, the grade of the concentrate was increased from 20.3% Cu to 28.7% Cu.

Jan 1, 2003

By F. Xie

Low gold and silver leaching kinetics has been commonly observed in traditional gold-silver cyanidation process, especially in those heap-leaching operations. The reactivity and availability of oxidant was believed to be the critical limitation for gold and silver dissolution. The occurrence of silver sulfide such as acanthite (Ag2S) in the ore may also result in low overall silver extraction. Leaching of gold and silver sulfide in the ferricyanide-cyanide solution has been investigated through rotating disc tests and the assistant effect of ferricyanide on increasing the dissolution rate of gold and silver was noticed. The potential use of ferricyanide as an auxiliary oxidant in gold/silver cyanidation process was proposed based on the results of leaching of gold-silver ores.

Jan 1, 2014

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By Jiongtian Liu, Jianjun Wu, Yongzhou Wan, Li Feng

"Mechanical Thermal Expression (MTE) is a developing non-evaporative lignite dewatering technology. It has been shown to effectively dewater high moisture content in low rank coals via the application of mechanical force and thermal energy at elevated temperatures. In this paper, the dewatering behavior of Yunnan Xiaolongtang lignite during the MTE-process was studied. Furthermore, how variations in temperature and pressure during the MTE process affect the surface oxygen functional groups and pore structure were also discussed using Fourier transform infrared spectrometer (FTIR) and mercury intrusion porosimetry (MIP). Increases in MTE temperature and pressure resulted in significant reductions in residual moisture content and moisture holding capacity, along with the increase of fixed carbon content and reductions of other elements content, especially oxygen content, which have been largely attributed to the destruction of the surface oxygen functional groups and porosity in lignite. The optimized technology conditions are temperature 150~220°C and pressure 7~10MPa. The residual moisture content of the lignite treated by MTE under the conditions of 200°C and 10MPa is decreased to 8%, while the dewatering rate exceeds 76 % and the calorific value approaches 22 MJ/kg. The experimental results offer a deeper understanding of the influence of process parameters on the lignite stuctures and properties. The reduction in residual moisture content, surface oxygen functional groups and pore volume under increasingly severe MTE conditions are suggestive of the structure changes that accompany increased coalification (rank) within the lignitic range."

Jan 1, 2014

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By C. H. Zhou

Cryogenic grinding of Printed Circuit Board will bring less pollution, reduce energy costs, smaller particles, regular particle size, efficient process, separation various materials due to different fracture toughness. Systemic studies of recycling discarded Printed Circuit Board (PCB) by low-temperature modification and cryogenic grinding have been made in this paper. Firstly test mechanical property of PCB at different low-temperature, including impact strength, flexural strength, and shear strength. Do experiment on the power consumption of different cooling temperature, The results show that the average power consumption is lower between -30? to -60? and the average power is decrease in evidence at -30?. Use ZKB type double roll shear crusher to crush PCB to 20mm×20mm particle size, in a temperature range of -10 ~ -30? Used R type mill to grind sample to minus 3mm under different working condition, the average power consumption is decrease in evidence from -10 ? to -30 ?, power consumption is the lest at rotational speed is 1180rpm.

Jan 1, 2014

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

By B. Friedrich, A. Weyhe, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990’s. Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used today in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals (RE) are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process described in this paper consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps. This process is capable of treating all types of Ni-MH-batteries. After comminution steel and organics are separated. The separated Ni-MH is smelted in an electric arc furnace. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’. Both the Nickel-Cobalt alloy and the ‘mischmetal’ will be directly used in battery production."

Jan 1, 2003

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By V. Y. Dementyev

Laboratory and pilot-plant testing using a sample of gold-bearing semi-oxidized ore from a Russian deposit followed by a flow sheet and reagent flotation mode development to design a plant was carried out in IRGIREDMET in 2009-2010. According to the developed flow sheet low alkaline flotation conditions are recommended in order to activate the surface of sulfides. The pH lowering from natural (7.5-8.0) to optimal (4.6-4.8) value using sulfuric acid provides for an increase in gold recovery. Before CIL, a final flotation concentrate is pretreated using pressure oxidation. It was found that the use of recycled solutions from pressure liberation in order to create acidic conditions for flotation instead of sulfuric acid during pilot-plant testing is recommended. The flow sheet offers the detoxification of remaining pressure oxidation solutions together with the flotation tailings. The carbonates presented in the tailings significantly reduce the consumption of lime for detoxification and allows for the use of two tailings dams instead of three. The first is used for the tailings of flotation and pressure oxidation recycled solutions, which were detoxified together. The second tailings dam is used for detoxified cyanidation cakes of the flotation concentrate. It was found during pilot-plant testing that flotation under natural and acidic conditions provides for 88.9 percent and 93 percent gold recovery, respectively. 4.1Au percent increase recovery was achieved due to the reduction of gold losses with flotation tailings and better quality of concentrates.

Sep 1, 2012

By N. I. Tyushkova

On the basis of detailed studying of mineral structure of ore and treatment products it is established that the given ore refers to oxidized Pb-Zn vein-disseminated ores. Technological special features of the basic ore minerals and the reasons causing their obstinateness that is defined by following features are revealed, presence at dominating quantity difficult to float lead minerals: mimetesite (9.67%), green lead ore(0.48%); non float: bindheimite (2.16%) and plumbojarosite (0.36%) and high assay of oxides and hydrous ferric oxides; also thin, emulsive and submicroscopic segregations of the defined minerals in swamp ore. As a result of researches the scheme of gravitational-flotation treatment was conducted in semi-industrial scale. It allows to receive two concentrates from ore: a lead gravitational concentrate of mark ??-4 with the assay of 55.5 % of Pb and 0.77 % of Zn; and a Pb concentrate of mark ??-7 with assay of Pb of 40.97 % and Zn of 1.39 %. The total assay of Pb in concentrates makes 81 %. The efficiency offered by gravitational-flotation schemes is defined by possibility for recovery of big impregnated lead minerals under gravitation. The use of this method of gravitation has allowed to recover such mineral as beudantide and to exclude irrevocable losses of lead in tails which are connected with this mineral. Scientific value of the presented researches is connected with the fact the problem of extraction of the oxidized minerals of Bb and Zn is rather difficult and insufficiently studied. Keywords: flotation, oxidized forms of Pb and Zn

Sep 1, 2012

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

The optimal design of flotation circuits is a complex task as the mathematical model is nonconvex and includes binary variables, making it difficult to obtain the global optimum solution. Furthermore, there are epistemic uncertainties in the evaluation of the performance of flotation and grinding units. This epistemic uncertainty is generated because semi-empirical models are used with parameters that are a function of the circuit design. Therefore, it is not possible to adjust these models based on experimental data as the experimental conditions are not known at the design stage. This paper analyzed the effect of the uncertainties in flotation units, grinding units, and both units simultaneously. As a result, this paper demonstrated that, for a specific mineral, few structures exist that are optimal for a wide range of values in flotation stage recoveries and liberation fractions in the grinding units. A remarkable aspect of this work is that it introduces grinding, one of the operations that most influences energy consumption in mining and has not been studied in depth in the design of flotation circuits. To demonstrate that there are few optimal structures for a specific mineral when there is high uncertainty in the process units, an a priori approach or first principles was used. Two methods of proof were used: proof by construction and proof by exhaustion. Proof by construction is the construction of a concrete example with a property to demonstrate that something having that property exists. In this work, two examples were considered in the proof by construction. In proof by exhaustion, the conclusion was established by dividing it into a finite number of cases and proving each one separately. Here, 30,000 cases were included for each example. This knowledge can be useful in circuit design including grinding, e.g., after selecting the circuit (or the most promising circuits), and the equipment design parameters and operating conditions can be defined based on simulation and laboratory tests.

Jan 1, 2018

By C. Suazo, O. Alruiz, A. Hofmann, I. Fernandez, W. Kracht, N. Mora

"Compañía Minera Dona Inés de Collahuasi, CMDIC, has developed a methodology that allows estimating economic benefit taking into account the variability of the ore characteristics (geometallurgical models). Currently, the grinding model allows predicting the treatment capacity, specific power and balls consumption for short, mid and long term planning. An alternative impact test to estimate SAG grinding parameters is presented in order to bring the geometallurgical model from mid and long term to short term planning. The impact test uses either the production bench or geological drill holes. This allows Geologists increasing the density of grinding parameters within the block model improving the geostatistical estimation of the rest of the blocks. The test requires a small amount of sample to obtain the requires grinding parameters for the grinding model in comparison to the well known grinding test and also, it can be performed easily and quickly by the geology team of a mining company. The alternative grinding test is presented in this article. The grinding model using this short grinding test has been successfully used in mining planning and the accuracy of the model is demonstrated using monthly average instantaneous throughput from January 2013 to March 2014, showing an average relative error of 5% and an R2 value of 0.9. Also, 111 individual variability samples were divided into two each, in order to compare the estimated grinding parameters based on this alternative test to the grinding parameters obtained from the conventional grinding test. The comparison shows an average relative error of 4% and an R2 value of 0.9."

Jan 1, 2014

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By Gábor Mucsi, József Faitli, Imre Gombköto, Sanjay Kumar, Zoltán Molnár, Balázs Ráczkevi, Ádám Rácz

"Generally, fly ash particles are very fine (< 100 ?m), mainly spherical and glassy materials form an outer shell on it. This paper deals with the laboratory investigation of ground fly ash based geopolymer. This material can be applied in many fields, mainly in the construction industry, e.g. non-structural elements, concrete, pavements and products, containment and immobilization of toxic, hazardous and radioactive wastes, advanced structural tooling and refractory ceramics, and fire resistant composites used in buildings, etc. The preparation of fly ash using high energy density milling is presented. Systematic experimental series were carried out in order to optimize the preparation process. The particle size distribution (LPSA) and structure of fly ash (FTIR) and the uniaxial compressive strength ,the permeability and structure of geopolymer product, furthermore the rheology of geopolymer paste were investigated. The product properties were studied as a function of the fly ash fineness. As a result of the investigation the relationship between the grinding circumstances, the ground material properties and the geopolymer characteristics was identified. It was found that the above mentioned physical properties of the geopolymer strongly depend on the grinding process."

Jan 1, 2014