Search Documents

By André Mans, Frans B. Waanders

Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof. A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process, which resulted in the liberation of Fe and subsequent formation of an oxihydroxide froth. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought.

Jan 1, 2003

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By C. Perez

In mineral processing plants it is important to estimate rock composition, size and grindability to improve control of the grinding process. It is well known that variation in ore grindability and size distribution directly affects mills power consumption and throughput. This paper extends a general machine vision approach for on-line estimation of rock mixture composition using color information. Our proposed rock lithological recognition method requires the following steps: division of each image into sub-images, color feature extraction using the Binary Quaternion-Moment-Preserving thresholding technique (BQMP) and support vector machines (SVM) for classification. The BQMP thresholding technique splits the image in two and chooses representatives of each half using the histogram as features. The statistical parameters of the color data can be expressed using the quaternion moments into the representatives. This method can be recursively applied to the sub-images, obtaining 5x2n features in n iterations. Once the feature vector has been computed, each vector is assigned to one of three classes using a classifier. The method was tested on a database containing 20480 sub-images (64x43 pixels) of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets: 15360 sub-images used for training and cross validation and 5120 sub-images used for test. The classification accuracy was compared with a method previously published based on a mixture of principal components analysis (PCA) for color, and wavelet texture analysis (WTA) for texture feature extraction. WTA-PCA approach reached a 76% accuracy in test while our BQMP method reached 90% of classification accuracy using only color features. Experimental results show that our proposed method yields excellent results compared to previously published results. Keywords: rock classification, lithological classification, grindability estimation

Sep 1, 2012

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By Vladimir E. Vigdergauz

"Bubble-mineral complexes could be formatted by an attaching of hydrophobic particles to the surface of air bubbles or by an evolution of bubbles from solution onto hydrophobic surfaces. Measurements of contact angles, detachment forces (DF), induction times (IT), evolution pressures (EP) and flotation recoveries (FR) for the studying of minerals wettability at various pH and electrochemical potentials were used. An analysis of the obtained IT results show that a process of bubble attachment to a mineral surface is a rather slow one and it will scarcely be enough for bubble-mineral complex formation under the conditions of real flotation.The ranges of adhesion potentials obtained by DF measurements, Figure 1, correlate with the data of floatability-potential for pyrite. The ranges of adhesion potentials obtained by DF measurements for galena (-1 ÷0.2V) and chalcocite (-0.5÷1.2V) correlate with the potential ranges of floatability for galena (<0.2V) and chalcocite (>-0.4V). An increase of the DF and the cathodic limit of the adhesion potential with increasing length of the hydrocarbon chain were observed. EP-pH curves for sulfides are a mirror-like to the DF-pH curves, Figure 2. Structure of solid-liquid and liquid-gas borders has a determinative importance for formation of bubble-mineral complexes and subsequently flotation results. Under vacuum on the mineral surface there are produced micro bubbles and preferably they will be appeared on the hydrophobic sites. Water structure breaks near a hydrophobic surface facilitate water mass destruction and formation of gaseous phase embryos under decompression in the impeller zone. It simultaneously reduces a probability of produced micro bubbles dissolution as a result of pressure increasing owing to constant fluctuation of liquid densities into impeller zone. Comparison of Taggart’s evaluation of the suction behind blades of the impeller of an agitation-froth machine and ABEP data on galena, Figure, shows that gas evolution will be observed in the range of 1300-2700 revolutions of impeller per minute for hydrophobic and hydrophilic surfaces successively."

Jan 1, 2003

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By Rodrigo Carvalho, Marcelo Tavares

"The accurate prediction of the outcomes in SAG grinding has been a great challenge to researchers and process operators. The use of Discrete Element Methods for modelling charge motion in tumbling mills allowed extraction of not only visual data, such as the position of the charge, but also the energy transfer in terms of the energy dissipated in the collisions. One of the advantages of DEM technique is its scalability to different mill sizes and some operational conditions such as speed and mill filling. Recently the Authors proposed the coupling between DEM outputs and modified Population Balance Models that with proper dedicated ore characterization tests allows the prediction of the outcomes of an energy transfer example. This modelling framework is called the Multi-scale Mechanistic Modelling. This paper shows the application of the Multi-scale Mechanistic Model to a set of pilot plant tests ran at different operational conditions. The prediction of the grinding outcomes and even the stabilization of the charge was achieved by the use of the Multi-scale Mechanistic Modelling framework. This approach has a great potential to become a powerful tool to design and optimize AG and SAG mills."

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONAcid pressure oxidation of high-grade natural acanthite was investigated in the range of 110-150°C and in the sulphate media. High acidity and low pulp density were used to prevent the precipitation of silver.RESULTS AND DISCUSSIONTwo sets of acanthite specimens were obtained from La Valenciana and Ingleterra mines, Mexico. Pressure oxidation tests were conducted on 1 litre scale in a standard 2-litre Parr titanium autoclave.EFFECT OF TEMPERATURE ON THE REACTION OF ACANTHITEThe effect of temperature on the rate of oxidation is presented in Figure 1. The rate of reaction increased with increasing temperature."

Jan 1, 2003

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By Andrei Kolesnikov

"The results of CFD modelling of complex heat transfer and fluid flow in DC electric arc furnace are presented. The model includes energy and momentum conservation equations for gas phase (freeboard), liquid phase (molten bath) and solid phase (walls and graphite electrode). Simulation revealed the temperature distribution in all elements of the furnace. The influence of the arc and melt resistance on the temperature distribution is discussed.Computational Fluid Dynamics (CFD) becomes a powerful tool for better understanding of the heta and mass transfer processes in industrial equipment. In current work commercial CFD software STAR-CD was used to analyse complex heat transfer in DC EAF, including forced and natural convection, conduction and radiation. The finite volume solver using body-fitted grid was used. The grids are non-staggered hexahedral grids and all variables are evaluated at cell centers. Steady-state calculations were performed with PISO algorithm. For the convective terms in equations the hybrid differencing scheme was used. An upwind differencing scheme was used for other terms. Conjugative heat transfer was taken into account in heat transfer calculations on gas-liquid and gas-solid interfaces. Radiation from the arc and inner surfaces of the furnace was calculated by a “discrete beam” approach. Source term in energy conservation equation was used to represent heat release in the zone occupied by the DC electric arc. The volume of this zone was calculated from semi-empirical equations. The Joule heat and heat due to chemical reaction in the melt were calculated through the source term expression in the energy balance equations for the slag and metal in the molten bath. The gas acceleration in the electric arc zone and stirring of the slag due to gas bubbles motion were accounted for by momentum source terms in the momentum conservation equations.All simulations were carried out using axisymmetric two-dimensional grid. The grid resolution was 20 cm per cell in most part of the furnace, except the arc region, where resolution was 5 mm per cell."

Jan 1, 2003

By M. Ghiani, P. Massacci, A. Manni, R. Peretti, Center for Mining and Mineralurgical Studies, S. Serranti

"The research study has been devoted to point out the better way to process a colemanite concentrate characterised by a high content of two kind of As sulphides (realgar and orpiment) finely disseminated in the matrix of the boron mineral.Scanning Electron Microscopy analyses have been carried out to determine all the mineralogical constituents and to evaluate their distribution, frequency and mutual relationships.There is a not neglectable part of realgar highly disseminated into the colemanite crystals.The orpiment recurs in small acicular crystals of 20÷30 µm in length and 5 µm in width, very difficult to liberate from the colemanite mineral particles.The colemanite concentrate, in fact, has been addressed to a chemical plant which products were boric acid and gypsum, the contaminated by As. It was unacceptable for further applications and very dangerous if rejected in the environment.Grinding tests under dry and wet conditions have been carried out in order to evaluate the liberation modality of the As sulphide minerals from the colemanite.Some difficulties have been overtaken in order to obtain a selective liberation of the As sulphides from the colemanite even if a certain decreasing in As grade in the higher size classes has been registered.All the comminution products have been analysed by SEM monitoring the liberation degree of the mineralogical constituents.Flotation tests have been carried out after different comminution flow sheet adopting different modulating conditions in order to evaluate the influence of the following parameters:• collector concentration versus contaminants concentration (As minerals) in the froths;• kind and quantity of the frothing agent to maximise the mineral recovery in the froths;• kind and quantity of the modulating agents to maximise the selectivity of the process;• conditioning modalities in order to obtain a suitable dispersion of fines and to avoid segregation of Asbearingparticles together with colemanite ones;• solid/liquid ratio of the pulp to minimise the water flow into the plant."

Jan 1, 2003

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By Sirish L. Shah

It is now common to have archival history of thousands of sensors sampled every second over long time. Yet we frequently have process engineers complain:??.We are drowning in data but starving for information??. How can these rich data sets be put to use? This paper addresses the issue of information and knowledge extraction from data with emphasis on process and performance monitoring including fault detection and isolation. Most of the major plant, factory, process, equipment and tool disruptions are avoidable, and yet preventable fault detection and diagnosis strategies are not the norm in most industries. It is not uncommon to see simple and preventable faults disrupt the operation of an entire integrated manufacturing facility. For example, faults such as malfunctioning sensors or actuators, inoperative alarm systems, poor controller tuning or configuration can render the most sophisticated control systems useless. Such disruptions can cost in the excess of $1 million per day and on the average they rob the plant of 7% of its annual capacity. Over the last decade the fields of multivariate statistics and data visualization and analysis methods have merged to develop powerful sensing and condition-based monitoring systems for predictive fault detection and diagnosis.These methods rely on the notion of sensor fusion whereby data from many sensors or units are combined with process information, such as physical connectivity of process units, to give a holistic picture of health of an integrated plant. Such methods are at a stage where these strategies are being implemented for off-line and on-line deployment. This article attempts to outline the field of sensor fusion - the application of signal processing methods, in the temporal as well as spectral domains, on a multitude and NOT singular sensor signals to detect incipient process abnormality before a catastrophic breakdown is likely to occur Keywords: Process analytics, process and performance monitoring, multivariate statistical analysis, sensor-fusion

Sep 1, 2012

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By Mojtaba Ghorbannezhad, Abbas Sam, Soroush Arabzadeh

One of the dewatering methods in mineral processing plant is filtration system. Disk filters are included the porous surface with pressure drop on both sides, Water in the pulp passes through the surface and solid particles remain as a cake on it. Wet concentrate production of magnetite processing plant at Golgohar Mining and Industrial Company with solid tonnage of 160 ton per hour and 49% solid amount contains 166 m3/h of water. In the present study, in addition to studying disc filter performance, the effective parameters on cake moisture were studied using Vacuum Bottom-Feed Leaf method (in the laboratory scale). Optimization was performed using the Taguchi method. The results showed that the cake moisture is reduced by increasing particle size and solid percentage (because of specific resistivity reduction), while the rate of cake formation and its thickness are increased. Also, it was found that by increasing pressure, the cake moisture is reduced and cake formation rate and its thickness are increased. In this study, the effect of fabric texture was also examined. Lowest cake moisture was obtained in condition of using compressed plain fabric with mono-multi filament fibres, pressure at 75kPa, solid percentage of 65 to 70, particle size (D80) equivalent to 123µm and disk rotation speed of 1.25 rpm.

Jan 1, 2014