Search Documents

By Evvie Chockalingam

Acid mine drainage (AMD) is a perennial problem particularly in abandoned mines, occurring due to the oxidation of sulphidic mine wastes. AMD is usually characterized by high concentration of dissolved metal ions, sulphate and low pH. The efficacies of substrates such as rice husk and the bark of Eucalyptus tereticornis (Sm.) are assessed for the removal of metal ions such as iron, zinc and copper from acid mine water obtained from an abandoned copper mine. Over 99 % of Fe, 98 % of Zn and 95 % of Cu removal could be achieved from acid mine water, with a concomitant increase in the pH value by three units using rice husk as an adsorbent. With respect to tree bark as an adsor-bent, about 96 % of Fe, 75 % of Zn and 92 % of Cu could be removed from the acid mine water with an attendant increase in the pH value by two units. The free energy of adsorption of the metal ions onto rice husk and tree bark is found to be negative in both the cases, while the adsorption process is endothermic in the case of rice husk and exothermic for tree bark. The adsorption process is found to adhere to the Lagergren pseudo-first order rate equation. The reduction of sulphate con-centration in the acid mine water is achieved using a typical sulphate reducing bacteria namely De-sulfotomaculum nigrificans. Desorption experiments indicate that about 88 % of Zn, 87% of Cu and over 77 % of Fe could be recovered from rice husk and over 70 % of Fe, 82 % of Zn and 77 % of Cu could be desorbed from the metal loaded tree bark using 5 M HCl. The possible mechanisms of metal ion and sulphate removal from acid mine water using rice husk and tree bark are discussed.

Jan 1, 2014

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By M. Bhartia

India is the 5th largest producer of steel in the world and is slated to produce more than 180 Mt by 2020. Expectedly about 50 % of this would be through the Blast furnace route and the rest through Sponge iron / DRI route. Considering that there will not be any major change in iron making technology by that time, the Blast operation would require lump ore (10-40mm) with around 64% Fe grade and sinter fines (<10mm) with 60% Fe (min) as its feed. DRI process would need calibrated ore of size 5-18 mm as the most suitable size of feed. It is also expected that of the total requirement of ore for the DRI route a significant part would be DRI pellets. In India, there is considerable debate going on regarding the technology to be adopted for the processing of iron ore and there is a lack of clear consensus. The above scenario indicates that the processing requirement of iron ore in the country would involve both washing technology as well as beneficiation technology. CDE Asia Ltd is in the forefront of iron ore processing in the country and the experience gained by the company over the last few years of functioning has led the company to believe that route to be adopted depends on the end product requirement and the starting grade of the feed. Keeping in mind the nature of the feed required for the Blast furnace & DRI operation; it is obvious that good washing technology would be highly beneficial to the iron ore industry. Depending on the grade of ore available the limits of washing will be decided and equipment for lump ore beneficiation such as jigs could be incorporated into the washing circuit. Scrubbing of ore either before washing or selectively scrubbing the lumps could be necessary. Very low grade ore and jig rejects would be required to be totally ground and beneficiated for the production of pellet feed in order to utilize the iron ore resources entirely. Another source of ore for pelletisation would be slimes generated from the washing process as well as the huge quantities already available in the tailings dams in the operating mines. Deslimimg and magnetic route of beneficiation could release at 30-40% of the Fe locked up in these tailings ponds/dams. The paper describes the concept with examples from operating plants and proposes how the adoption could be engineered through test work and proper plan of integration. Keywords: washing, beneficiation, iron ore, lumps, sinter fines, pellets, jigs, screens, evowash, nanowash, thickeners, log washers, drum scrubbers

Sep 1, 2012

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Kevin Galvin, James Dickinson

"The Reflux Flotation Cell (RFC) consists of an inverted fluidized bubbly bed, located above a system of parallel inclined channels. This novel arrangement enhances the hydrodynamics of flotation in a number of ways. Firstly, the free-surface of the flotation cell is enclosed via a fluidized bed distributor, ensuring uniform application of wash water to promote desliming. Secondly, foams can be variable in their stability and lack permeability. Hence this system is preferably operated in the absence of foam, instead opting for a bubbly zone of high bubble volume fraction through the use of a very high gas flux and/or wash water flux. Discharge of the product proceeds upwards through a central port of narrow cross-sectional area. Thirdly, the system of inclined channels increases the segregation between the bubbles and the water, ensuring the bubbly zone remains contained within the upper vertical zone, and the liquid flux reporting to the overflow is low. The expanded operating regime of the RFC was investigated by covering a very broad range of gas fluxes, up to 5.5 cm/s, and wash water fluxes, over 2 cm/s. Both laboratory and pilot plant performances were quantified by the recovery of hydrophobic particles and rejection of the hydrophilic particles, using model and industrial coal feeds. The new system hydrodynamics was found to offer significant advantages in flotation kinetics, desliming, and particle recovery across a broad particle size range. Bubble interfacial flux reached as high as 600 m2/m-2s-1. The upper system consists entirely of a high volume fraction of bubbles, which provides a "safety-net" to protect against the detachment of coarse particles, and a highly permeable zone for counter-current washing of the flotation product. Under relatively extreme conditions selective stripping of the product is observed, resulting in grade recovery values beyond those achievable using the tree flotation method."

Jan 1, 2014

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014

By X. O. Xia

This paper introduces a kind of flotation machine for nonferrous metal, ferrous metal and non-metal minerals. With the application and development of flotation machine, researching the designment of master parts, including tank, impeller, stator, false bottom. Through the commercial run to validate the correctness of designment, achieving satisfied technical and economic target and supplying a kind of efficient and reliable flotation machine.

Jan 1, 2014

By S. Dwarapudi

Pelletizing of Indian chromite ores is more challenging due to their high refractory nature. High Cr/Fe ratio and high MgO content in these ores demand high firing temperatures and longer firing cycles but often result in low strength fired pellets. Aim of this study was to develop cold bonded chromite pellets for smelting in submerged arc furnace (SAF) from chromite fines using suitable binder that induce less gangue into the pellets but cures quickly. Different binders were studied through laboratory pelletizing experiments for their suitability for cold bonding the pellets. As result, a composite binder comprising organic and inorganic binding agents was found to be suitable and pellets made from the same were tested for their low and high temperature behavior. High temperature reduction studies revealed that pellets were resistant to disintegration up to 1200 °C.

Sep 1, 2012

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By S. Gerl

Since Schönert, 1980 a multiplicity of scientists have dedicated themselves intensively to the scientific investigation of wet grinding in agitated media mills. The achieved research results led to a clearly improved understanding of the comminution mechanism in wet operated agitated media mills and in consequence also to clearly more efficient machines. In contrast to this the standard of knowledge on dry grinding in agitated media mills is still very small. The practical experience from numerous plants shows however that the transferability of knowledge from wet grinding to the dry grinding regarding transport phenomena and comminution behaviour, influence of the operating parameters and also wear is very limited. In the industrial application above all the continuous mode of operation is preferred. The main problem which has to be solved in agitated media mills is minor the comminution itself, than rather the question of the trouble free material supply and material extraction as well as the cooling of the mill. The agitated media mill MaxxMill® offers an innovative concept to overcome the feeding and extraction problem with its rotating grinding chamber, the eccentrically mounted agitators as well as the eccentric flow deflector with integrated material supply. Because of the pneumatic extraction of the ground materi-al cooling of the milling chamber is not necessary. On a MaxxMill ® laboratory mill with a 5 litre grinding chamber volume extensive parameter studies were carried out to study the influence of operating parameters on the continuous dry grinding of quartz sand. The test were performed in a continuous single pass operation without classification of the final product. Apart from the influence of the throughput rate on fineness above all the influence of the agitator and grinding chamber speed as well as the grinding media size was examined.

Jan 1, 2014

By Pramila Misra, Jibardhan Meher, Debadutta Das

The concentrated coal-water slurry has been receiving considerable attention recently due its ability to replace fossil fuels. Attainment of stable and concentrated slurry has been succeeded so far through several physical and chemical techniques. The present article reports the formulation and stabilization of a highly concentrated coal-water slurry formed from five varieties of non-coking coals with variable ash contents obtained from Eastern part of India, employing three varieties of starch esters, such as starch benzoate, starch formate, and starch carbamate as dispersant. The apparent viscosity of the modified coal-water slurry has been measured by varying coal loading, dispersant percentage, pH, temperature, etc. The apparent viscosity of the slurry has been found to be decreased substantially on addition of 0.8% of adsorbate in the slurry. The particle-particle interaction has been considerably decreased and stable concentrated coal-water slurry containing high weight fraction of coal (61.5-63.5%) has been achieved in each case. The slurries stay in a non-settling form for about a month with viscosity in a permissible low range. The coal-water slurry has been found to behave as a non-Newtonian liquid. Comparison of the zeta potentials of the naked and modified coals evidences that adsorption of the dispersants at coal-water interface results in inhibition of the agglomeration of coal particles through mostly steric repulsions.

Jan 1, 2014

By R. Mukherjee

Consistency of Run-Off-Mine (ROM) quality plays an important role in mineral processing which is not very often talked about. The major impediment is limitation of sampling ROM ore, which makes processing plants to run without any realtime feedback on ore quality that comes in. The process of direct determination of Run-Off-Mine (ROM) ore quality is expensive and time consuming as drawing and preparing representative samples from blasted muckpiles are constrained by large sample size and inherent heterogeneity in terms of size and chemistry. In absence of techniques for direct measurement of quality, monitoring and control of ROM, feed to the processing plant at Joda East Mine, like all other iron ore beneficiation plants worldwide, is largely based on blasthole sampling and subsequent chemical analyses of blastcone chips. While such indirect methods proves to be more accurate for representing whole of a mining block or blasted muckpile (~30-50KT/blast), it is indeed a challenge to ascertain and predict day to day input quality for a part there off. This eventually leads to a gap between predicted and actual ROM quality, resulting in difficulties in process control, in turn, and leading to wide swings in product quality. Hence, it is imperative to bridge the gap between predicted and actual ROM quality by arriving at means, which ensure consistent plant feed grade to deliver consistent output. The paper discusses an efficient and affordable alternative for effective prediction of ROM alumina which has been developed by integrating blasthole quality database in GPS based Truck Dispatch System (GPS-TDS) at Joda East Mine. Initially, GPS-TDS has been installed for optimizing production parameters only, but this development has helped in further utilization of GPS-TDS for real time quality monitoring by improving ROM grade prediction and scheduling from several ore blocks in active mining areas. Keywords:run-off-mine (ROM), blast hole, feed grade, GPS-TDS

Sep 1, 2012

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By Ventsislav Stoilov, Angel Angelov, Ivan Korolev, Antti Remes, Todor Pukov, Stoyan Gaydardzhiev

"The process modeling and simulation studies aim for better process operation and favorable environmental impact. The objective of this work is to set up a simulation model of the Assarel copper flotation circuit for planning and optimization of the process with the aim of increased metal recovery. The model is parameterized based on laboratory flotation tests of ore samples from the Assarel mine together with mineralogical studies by X-ray diffraction (XRD) and Mineral Liberation Analysis (MLA). A combination of several techniques allows reliable identification of mineralogical composition of the selected samples. The changes in the proportion between sulfide minerals in various products along the circuit have been also documented. Further, this information is used in the simulation model and in data reconciliation procedures for establishing mass balance. The simulation accuracy is studied by comparing the simulations with the plant survey based mass balance. Constructed simulation model can be used to run alternative process scenarios. As an example, the flotation circuit performance with different reagent regimes is simulated based on data from batch flotation tests. Two reagents were considered for this purpose, dithiocarbamate-based one and xanthogen formate/mercaptan blend. It has been revealed that these reagents do not have the same influence on the selective flotation. The one improves flotation of gold and overall recovery but without notable selective action. In contrast, the other showed better selectivity towards copper, rejecting more gangue and lowering gold recovery. The model is also applicable for process optimization studies with different feed compositions, flowrates and circuit configurations. INTRODUCTION In the pursuit for elevated technological indicators, finding an optimal set of process parameters fully utilizing the potential of the equipment is a key factor to success. Over the past decades, there has been a substantial development in flotation circuit optimization through performance benchmarking using metallurgical modelling and steady-state computer simulation. Practical simulation engineering tools are based on experimental data obtained from laboratory tests and from plant surveys and operation data. With the help of flotation models, it is possible to study grade-recovery response with different feed compositions and throughputs, and with various cell-operating parameters, as well as to evaluate and design different flowsheet configurations. Outotec’s HSC Chemistry® software, which incorporates simulation and mass balancing modules alongside with several other tools, can assist with this optimization (Mattsson et al., 2015)."

Jan 1, 2018

By V. K. Chandaliya

N-Methyl-2-pyrollidone (NMP) has already been proven a good solvent for extraction of coal. It is believed that organic components of coal are likely to be dissolved with the solvolytic power of NMP. During dissolution process, original coal also gets disintegrated and thus helps in further extraction. Coal extraction highly depends on temperature, coal to solvent ratio, N-Methyl-2-pyrollidone (NMP) to Ethylenediamine (EDA) ratio and the size of coal particles. The process has been established in the laboratory. There is no reference available beyond lab scale. In present study, we are running a bench scale plant with 40 kg/batch capacity. Design of experiment was done in such a way that the optimum zone of the process gets evaluated for clean coal having low ash with high yield. Bench scale plant trial was conducted based on optimum zone developed during design of experiments (DOE). From the DOE analysis it was observed that feed size and coal to solvent ratio are important parameters for this process. Total 27 experiments (four factors with 3 level of variation) were designed through Box-Behnken model. It was observed that -0.5 mm feed size of coal, 150 °C extraction temperature, 17:1 NMP to EDA ratio, 1:9 coal to solvent ratio was optimum conditions. The results obtained at optimum conditions are 50% clean coal yield with 5% ash.

Sep 1, 2012

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012