Search Documents

By David Deglon, Martin Harris, Mehdi Safari

This paper investigates the effect of energy input on the flotation of galena in a novel oscillating grid flotation cell (OGC). Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Previous work was limited to quartz (-100 µm). Galena (-150 µm) was floated in the OGC at power intensities from 0.5 to 3 W/kg using 0.13, 0.58 and 0.82 mm mean bubble sizes (d10) and at three collector dosages. Results show that the effect of power intensity on flotation kinetics is strongly dependent on both particle and bubble size. For fine particles (-19 µm), increasing energy input increases the flotation rate at a low collector dosage but leads to an optimum at both the moderate and high collector dosages. For intermediate particles (+19-38 µm), increasing energy input has no effect on the flotation rate at the low collector dosage but leads to an optimum at both moderate and high collector dosages. For coarse particles (+38-150 µm), increasing energy input has no effect on the flotation rate at the low collector dosage and leads to a general decrease at both moderate and high collector dosages. Optimum conditions for fine particles are using small bubbles at a moderate collector dosage and an energy input of around 2 W/kg. Optimum conditions for moderate particles are using small bubbles at a high collector dosage and energy inputs of around 1.0 W/kg. Coarse particles do not benefit from agitation.

Jan 1, 2014

By G. A. Wierink

This paper discusses a new method to increase flotation recovery. As known from literature, fine and coarse particles have different flotation rate constants, hydrodynamic behaviour and require different reagent regimes. The device discussed allows separate processing of finer and coarser slurry by extraction of a third stream, carrying finer slurry, from the flotation cell. By separate treatment of fine and coarse slurry operational conditions and so flotation recovery for both may be optimized more efficiently. Extraction and classification of the third stream is accomplished by low speed centrifugation and Taylor-Couette flow separation. This Dual Outlet Device (DOD) can be installed in a traditional flotation cell without need for equipment replacement. In order to asses different design options for the DOD a transparent laboratory scale model was built. For this scale model Computational Fluid Dynamics (CFD) simulations using the RANS k-e and LES turbulence models were performed. Essential insight in the dominant flow systems relevant to optimal operation of the DOD was obtained from the CFD simulations and flow visualization tests with the laboratory scale model. Based on these findings a number of configurations were investigated at pilot plant scale in a 5 m3 Outokumpu flotation cell. The results of the pilot plant study show that utilization of the DOD provides a method for in-cell control over particle size distribution in the slurry. Use of the DOD in a flotation cell may enhance flotation recovery and decrease flotation reagent consumption significantly, against marginal investment and operation costs.

Jan 1, 2014

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By R. Paturi

Mill liners play an important role in the operation of a mineral concentrator influencing the throughput, availability, power drawn and the efficiency of the mill in the plant. Liners protect the shell and transfer energy to the grinding charge. Metso Technology Development has conceptualized, developed and successfully implemented physics based 3D DEM simulation techniques to predict charge motion, power drawn, energy spectra and wear over the life of the liner. This paper will present a case study of shell liner optimization for a 34? SAG mill including the input data requirements, and shell liner optimization methodology using the 3D simulations that eliminates the need for the traditional expensive and lengthy proto-type testing. These simulations will cover ball and particle movement, liner wear and mill power draw, and do not cover particle breakage and slurry flow. Even the liner manufacturers lack the ability to provide this type of qualitative and quantitative information on their products. The data from these simulations provides the plant engineers a scientific basis for their decision making and thus eliminates guess work. Keywords: liner, optimization, multi-physics, 3D-DEM

Sep 1, 2012

With the ambitious target of adding another 2,00,000 MW of power generation by the year 2017 in India the demand for coal is bound to grow. The non-coking coal deposits in India are characterized as high ash and difficult-to-wash coals. Quality improvement by beneficiation is almost mandatory due to MoEF notification to use <34% ash coal for all power plants except those located at pithead. Most of the coal washeries in India are based on wet process, where the coal fines are allowed to settle in thickeners. The coarser particles settle faster leaving the fine particles suspended for longer period. The dispersed fine coal particles contain some surface charge, which leads to the development of electrical repulsion between the particles, and as a result of this, the suspension becomes more stable. In order to destabilize the colloidal suspension, flocculants are usually added, so that the settling rate of the fine particles also increases. These flocculants are of cationic, anionic and non-anionic depending upon the type of charge released when dispersed in water. The flocculants may act partly for charge neutralization and partly for inter particle bridging and electrostatic patch formation. The effectiveness of any type of flocculants depends upon the molecular weight and charge density of the polymer. The paper discusses the settling behavior of non-coking coal fines suspension by using different flocculants. Keywords: floculent, coal fines, sedimentation rate, effluent

Sep 1, 2012

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By C. Hazotte, M. -O. Simonnot, V. Houzelot, B. Laubie, M. Guilpain, B. Jally

"More than 400 plants in the world are able to accumulate nickel (Ni) in their aerial parts at concentrations higher than 10 g per kg of dry biomass. Then, Ni can be recovered from the biomass of these hyperaccumulator plants. Agromining is a chain consisting in growing such plants and producing metal. It has been developed thanks to the combined know-how of agronomy and hydrometallurgy. Hydrometallurgical processes have been designed; two different pathways were developed: i) acid leaching of ashes after biomass combustion and ii) direct Ni water extraction after biomass grinding. Experiments with 2 species of Ni hyperaccumulators (A. murale from the Balkans and R. bengalensis from Malaysia) have shown that the first process is very robust and transposable. For the second one, the way Ni is stored in the plant has a strong influence on extraction. A. murale transformation was explored in more details from the lab scale to the pilot scale. Results proved that Ni is totally transferred into the aqueous phase after 2 hours at 90 °C. A life cycle assessment has clearly shown the environmental interest of this approach (especially by detoxifying agricultural soils). INTRODUCTION Agromining is an emerging phytotechnology aiming at recovering metals thanks to hyperaccumulating plants (van der Ent et al., 2018). These plants are able to accumulate very high concentrations of metal in their aerial parts. For example, for nickel, the hyperaccumulation threshold is 0.1%, i.e. 10 grams of metal per kilogram of dry biomass. There are some advantages to use this technology instead of conventional mining techniques: •,Treating unconventional metal resources: they can be (i) natural soils with low concentrations but also low fertility because of the metal presence (like serpentine soils for Ni) (Bani et al., 2015), (ii) mine tailings or (iii) industrial wastes (like surface treatment sludge) after soil construction (Rue, 2017);"

Jan 1, 2018

By Xiaoxu Sun, Jianchao Yao, Jiancheng He, Shijie Lu, Hongxi Zhou

"The ball mill performance relies on impact grinding, but it has disadvantage of the lower efficiency when the ore is finer; while tower mill relies on friction shear affection with high energy efficiency, which is considered to be one of the most potential fine grinding equipment all over the world. Generated by the agitator device, the internal media movement is complex because of comprehensive interaction of screw mechanism, cylinder structure and adjacent media, which is the key factor of grinding process. But the kinematics parameter ,such as speed, acceleration, stress and so on, of media motion cannot be obtained through traditional laboratory test method, which restricts deeply research on finer grinding mechanism seriously. In order to solve this problem, characteristics of media motion in tower mill is studied via the discrete element method. Coefficient of restitution, coefficient of static friction and coefficient of rolling friction are the key parameters affecting the media movement, which were calibrated by stacking angle test firstly. A 3kW tower mill is established as the model for simulation. At last one appropriate simulation strategy is selected to increase simulation accuracy. The characteristic of media motion is obtained based on the computer simulation analysis: macroscopically, the media in tower mill is a dynamic equilibrium state generally accompanied by spiral up and down movement all the time. And it has been found that the maximum lifting height is proportional to the rotation speed of agitator shaft. The velocity of media at the edge of screw stirrer is biggest, while the velocity of media near the cylinder wall is smaller, so the grinding performance between the two ring areas is the best. The rotational speed of agitator shaft and media filling ratio are the two most important operating parameters in tower mill. The impact curve of two main operating parameters on the grinding intensity and energy efficiency are obtained. All these can provide theoretical basis and technical support for operating parameters setting of industrial tower mill."

Jan 1, 2018

By Brabcova Z.

This contribution deals with bubble adhesion on particle surface which consists of three steps ? the liquid film thinning, the film rupture and expansion of the three phase contact (TPC). Our attention is devoted to the third step ? to the description of the TPC expansion. Three-phase contact line expansion can be theoretically described using hydrodynamic and molecular-kinetic models. Both of these models were originally developed for the interaction of the bubble with horizontal plane in pure water. Our experiments deal mainly with the interaction of the bubble with the inclined plane in the solution of surface active agents. It was proved experimentally that molecular-kinetic model corresponds also to these conditions and this model was used for the description of the TPC expansion. The model is based on the theoretical description of the bubble contact angle on the three-phase interface. These contact angles change dramatically from 180o to equilibium (Young) contact angle close to 90o. Modificated ADSA method is used for the calculation of the contact angle. This method utilizes the Laplace equation of the capillarity; the bubble profile and the contact angle are evaluated using the set of experimental points around the edge of the bubble. The comparison of the experimental and calculated bubble profile shows a good agreement. The aim of the project is to describe the process of the TPC expansion during the adhesion of the bubble with the diameter up to 1 mm. Inclined planes were used instead of an experimental solid particle. Our experiments were provided in the solution of surface active compounds. The process of the adhesion was recorded using high-speed digital camera and images were evaluated using the image analysis software NIS-Elements. Calculations were performed using the MATLAB software. Keywords: bubble-particle interaction, adhesion, three-phase contact, contact angle

Sep 1, 2012

By S. H. Morar

Froth stability is widely recognized as a key driver of flotation selectivity. It is well known that froth stability is affected by the type and quantity of surface active reagents present (frothers), and the concentration and hydrophobicity of solid particles present. While some studies have been performed on the effect of frothers on froth stability in three-phase systems and the hydrophobicity of particles present, very little work has been performed on the effect of solids loading on froth stability. This may be due to insufficiently robust measurement techniques. This paper investigates the use of a new machine vision measurement to measure solids loading, and the relationship between this measurement, bubble size, and bubble burst rate on the froth surface. Keywords: froth flotation, machine vision, solids loading

Sep 1, 2012

By G. Voiloshnikov, A. Bogudlova

"The deleterious effect of carbonaceous matter during cyanidation of gold ores (so called preg-robbing) has been recognized for many years. Based on this, a new method using flotation to reduce the content of carbonaceous matter was developed. Low-sulfide gold-bearing ore with carbonaceous matter of 0.14% from a Russian deposit was processed. The purpose of these tests was to compare two flow sheet options. Option I comprised removal of carbonaceous product prior to sulfide flotation. Option II comprised removal of carbonaceous matter from flotation concentrate. It was found that the content of carbonaceous material can be reduced in sulfide gold-bearing concentrate prior to leaching. High gold recovery was observed during the separation of carbonaceous material prior to sulfide flotation using Option I. Due to lower reagent consumption the costs for reagents were decreased using Option II. The results have shown the effectiveness of a new method. Patent No. 2783808 was obtained for removal of carbonaceous material prior to sulfide flotation. This information will be used to design a large processing plant flow sheet in Russia."

Jan 1, 2014

By S. Chuanyao

In last decade, along with its booming Chinese economy, China?s higher education has experienced rapid growth. In 2010, the number of various colleges totals more than 3500, with 2.2 million faculties registered. Currently there are almost 30 million students studying in the colleges, 3 times more than 10 years ago. Mineral Processing was initiated in 1949 as a sub-discipline of Mining Engineering, one of the 13 first level disciplines. Mineral Processing is now established in 34 Chinese colleges, recruiting 2600 undergraduate students, 540 postgraduate students and 100 PhD students every year. A further 9 institutes offer postgraduate education in this field. More than 3000 graduates majoring in Mineral Processing join the industry or institutions each year. The four-year undergraduate teaching and practical training in the colleges is designed to produce qualified mineral processing professionals. This includes courses in mathematics and natural science, fundamental engineering and basic and specialization courses. Recently, the ?Excellent Engineer Program? was launched to strengthen students? practical capabilities. This is a 3+1 teaching and training model; 3 years of theoretical course study plus 1 accumulated year of various practical studies, either inside or outside the college. As for graduate employment, mining-related major graduates have been in a good demand thanks to the intensive investment in mineral sector by Chinese companies. The shortage of experienced metallurgists generates a greater than 90% employment rate for Mineral Processing graduates. However, the biggest problem we are still facing is the gap between the quality of the graduates and the requirements of industry, as a result of occupation attraction, teaching systems, faculty quality, and so forth. Another problem is international orientation. Although nowadays Chinese-foreign cooperation in college education is popular, collaborative mineral related projects are far less common, leaving much room for improvement. Looking ahead to the next 10 years, we still have the right reasons to estimate continued prosperity in the minerals sector as well as mineral processing education in China. A brief analysis and views on this will also be shared in the presentation. Keywords: China, mining engineering curriculum, excellent engineer program

Sep 1, 2012

By R. J. Batterham

The science and practice of mineral processing has been driven for many years by the same set of challenges that shape the mining industry ? demand and supply, grades and their decline with time, mineralogy and the need to handle more complex ores, disposal and minimising of wastes and the availability of water, power, skilled labour and the like together with increasing expectations from the community, concerns on sustainability and safety and, as well, climate change forcing a more targeted approach on energy. In this paper, the author builds on previous reviews to the IMPC and suggests that while step changes are long overdue, the unprecedented demand mitigates against drastic changes. That said, the ?Mine of the Future? is already requiring some different approaches.

Jan 1, 2014

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018