Search Documents

By J. Lampke

The superior characteristics of iron ore pellets compared with natural ore and sinter are well known. Due to the higher grade and bulk density they show improved transport and material handling properties. While charging blast furnaces with pellets an increased productivity is realized through pellet?s uniform structure and composition. The increased productivity is caused by a high permeable furnace burden with a decreased coke usage via fuel injection and oxygen enrichment. Therefore, a narrow pellet size distribution and a minimum content -6.3 mm are necessary (Meyer, 1980). The required pellet size distribution can be achieved on the one hand by screening the fired pellets after the induration furnace and recycle the undersized pellets. On the other hand it is possible to produce high quality iron ore pellets with a high degree of sphericity, the important narrow grain size distribution ranging between 9 to 16 mm with high green strength directly in the pelletizing device. To produce high quality green pellets, possibilities and knowledge about adjustments of the pelletizing device are necessary. The paper presents a classification of state of the art pelletizing systems in accordance with the advantages of the pelletizing disc and pelletizing drum in issues like adjustability, green pellet quality, the recycling rate and the space requirement. By a systematization of the influences on pelletizing the common reliance of objectives on influence like pelletizing moisture, disc inclination, rotational speed, mass flow and rim height are given. A variety of industry-proven examples are shown, too. Keywords: Pellet, iron ore, pelletizing, pelletizing disc

Sep 1, 2012

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. In contrast to landfill and incineration, application of digested sludge comprises the recycling nutrients and organic matter and reflects the policy of resource conservation and sustainability in waste management. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.The digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was the first merit to apply the sludge to agriculture in dry areas. Secondly, the sludge was rich in macro-nutrients (N, P, K) and a series of micro-nutrients (Ca, Mg, Mn, Na, Fe, Cu, Zn, B). The water-soluble fractions of macro-nutrients in the sludge were found considerably low. This implied that the loss or leaching of the macro-nutrients from the anaerobic sludge to the aqueous environment be slow. The nutrients loss owing to leaching could be reduced. However, because of a lower macro-nutrient content of the anaerobic sludge, comparable to the chemical fertilizer, it is advisable that the anaerobic sludge be applied together with commercial fertilizer to the agriculture land. Thirdly, the anaerobic sludge had strong selective adsorption affinity for heavy metal ions; non-heavy metal ions such as K(I) and Ca(II) could be released easily from the sludge in a wide pH range, such as pH from 1.0 to 8.0. Since the metal toxicity to the environment mainly comes from the mobile heavy metal ions, the selectivity to adsorb heavy metal ions of the anaerobic sludge can be utilized to reduce the availability of heavy metal ions to plants and humans in aquatic environment. Fourthly, the anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion."

Jan 1, 2003

By P. Holtzhausen, L. Auret, B. Lindner, A. Haasbroek

"Spiral concentrators offer a cost effective way to separate valuable minerals from gangue by displacing lighter materials to the outside, and heavier materials to the inside of the spiral. The separation can be seen as visible concentrate bands and splitters are set at the bottom of the spiral to effectively split the ore into various densities. As there are typically many spirals in a concentrator plant, it becomes ineffective to continually adjust the splitter positions manually. Vermaak et al. (2008) proposed to use image recognition to detect the concentrate bands, thereafter, creating a model predicting the positions under certain input conditions. This model could then be used for optimisation and/or control of splitter position or band position. In contrast an online concentrate band detection system would provide real time concentrate band positions without losing accuracy due to model generalisation. These systems are usually expensive and time consuming to develop, due to a lot of centralised features required (image capturing, image processing and/or feedback to a controller). This study took advantage of the recently developed Raspberry Pi minicomputer to perform rapid prototyping of an online image processing sensor. The Raspberry Pi, and accompanying camera module, offers a portable Linux environment which can natively run the required image processing algorithms. Furthermore, extensive use of OpenCV was made to reduce development time, by relying on existing and proven algorithms to detect the concentrate bands. The Raspberry Pi also incorporates generic input/output ports which can be used in future work to provide the signal to a controller. In conclusion, the Raspberry Pi was successfully used to perform real time concentrate band position detection on a spiral concentrator. This solution is more general than an experimentally identified input-output model and may be used for control or optimisation studies in a wide array of spiral concentrators."

Jan 1, 2014

By R. Venugopal

The paper reviews the development of Mineral Engineering education and training programmes in India. It highlights the major academic programmes and describes the evolution of the curriculum and design of courses in response to the changing requirements of India?s mineral and coal industries. An outline of the efforts needed to sustain and further improve the existing programmes is also provided. Keywords: manpower, mineral engineering

Sep 1, 2012

By A. F. Usov

The paper is concerned with an analysis of the experience gained in development of special electro-technical installations applied in electric-pulse destruction of materials. A principle scheme of an electric electric-pulse installation is given, and electric circuit variants of its blocks made on various element bases are discussed. Also assessed are some ideas to further improve the technical and economic characteristics of the equipment.

Jan 1, 2014

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By J. Menuge, G. Barker

"Liberation (QEM-SCAN) and surface chemical (time of flight secondary ion mass spectrometry -ToF-SIMS) analyses have been undertaken on plant Pb circuit flotation samples with the aim of defining the factors resulting in sub-optimal recovery. Lead flotation circuit feed, cleaner concentrate and tails samples were examined on a size-by-size basis using QEM-SCAN. Sulfide minerals accounted for approximately one third of the flotation feed with pyrite making up 16 wt.%, followed by sphalerite (13 wt.%) and galena (3 wt.%). Non-sulfide gangue minerals comprised calcium carbonates calcite (26 wt.%), dolomite (14 wt.%) with quartz, feldspars and barite all contributing > 5 wt.%. QEM-SCAN analysis indicated that liberation was not the primary cause of the poor flotation response. Principal component analysis was applied to the ToF-SIMS data derived from five samples (as for QEM-SCAN plus rougher concentrate and tails) to enable identification of correlated surface chemical components. Although a significant range of correlations were observed we focus here on those that show a discernible pattern throughout the float circuit. It was found that for the flotation feed the surface of galena were largely obscured but where Pb was observed there was a strong correlation to surface Fe. For the rougher and cleaner concentrates the galena surfaces were relatively clean with no correlation to Fe for the rougher concentrate and minor correlation in the cleaner concentrate. However, in the rougher and cleaner tails the clear correlation of galena with Fe was again apparent. These results suggest, in combination with prior studies of pyrite morphology, that the principal factor effecting grade is the rapid oxidation of the framboidal pyrite resulting in the contamination of the galena surface with a high loading of hydrophilic oxidised Fe species, thus depressing flotation."

Jan 1, 2014

By F. Molhem, S. Banisi, H. R. Montazari, E. Arghavani, Gh. R. Biniyaz, Gh. A. Parsapour

"Water plays a key role in mineral processing plants and to process one ton of ore 2.5 ton water is needed. Thickeners are commonly used for dewatering and recovering water in most processing plants. The underflow pulp density is increased by sedimentation of particles and clear water is recovered from the overflow. One of the issues related with using the process water is the presence of suspended fine particles in the clear overflow water which can create blockage in transfer pipes. The froth formed on top of thickeners is the main cause of this problem. In this study, a method to decrease the froth formed on the Sarcheshmeh Cu-Mo thickener surface was introduced and implemented. At the first stage, the old punched plate feedwell was removed and it was replaced by a vane type feedwell. A spray water ring using fish-tail type nozzles was then installed to break froth layers by water. These modifications led to 63% relative reduction in the water turbidity, 11% relative increase in the underflow solids concentration, 20% relative reduction in torque, 19% relative reduction in its standard deviation and an increase of 6% in water recovery.INTRODUCTION The Sarcheshmeh copper complex, the largest copper producer in Iran, located in southern Iran. In the processing plants of this complex, over 250,000 m3 of water is consumed daily. Because of a lack of water in this area and very low yearly rain fall (150 mm), water plays a vital role in the complex. As a result, it is then aimed at maximum water recovery by taking all necessary measures. The recycled water in order to be used should not contain any suspended solids indicated by low turbidity."

Jan 1, 2018

By R. Van Hille, A. E. Lewis

"The precipitation of a selection of metals from both a synthetic and an actual metal-rich effluent was investigated. The experimental aspects of this study were carried out in a two-stage process consisting of a pre-treatment clarifier and a fluidised bed (pellet) reactor. Each unit operation in the two-stage process was investigated separately. The pretreatment clarification stage at pH ˜ 5 resulted in a 99.9% removal of iron and 97.3% removal of aluminium.The pellet reactor was used to precipitate nickel as nickel hydroxy-carbonate from a pure stream and a removal efficiency of 99.6% was achieved. The high local supersaturation at the reagent inlet points caused the formation of a large amount of fines, but these agglomerated onto the pellets up the length of the bed (See Figure 1).For copper precipitated as copper sulphide from a pure stream, a maximum removal efficiency of 92% was achieved. The high local supersaturation at the reagent inlets also caused the formation of a large amount of fines, but the extremely sparingly soluble nature of copper sulphide meant that the fines were not agglomerated up the length of the bed. In Figure 2, the global supersaturation ratio was relatively low, and thus there is little homogeneous nucleation and degree of fines formation. However, the fines occurring after the third sulphide input point (at 30cm from the bottom of the bed) indicate that local supersaturation also plays a critical role in fines formation. It was therefore concluded that, for the copper sulphide case, it is essential to control the supersaturation at the inlet points in order to prevent fines formation altogether, as it is not possible to agglomerate the fines once they exist in the bed."

Jan 1, 2003

By Hernán Menares, Diego Hernández

"Over the last few years, the copper mining industry has been facing a changing scenario with respect to both the market and society which has resulted in taking a closer look at the way in which mining is being done. The cycle of high metal commodity prices of the last decade left the industry with high costs. Together with increased environmental and social requirements, a decrease in ore body quality, scarcity of resources such as human capital, water and energy, has resulted in an ever-increasing challenge to make a profit out of new ore bodies but also to maintain the current operations in the longer term competitive. The major challenge is to create value for all stakeholders, exploiting ore bodies that nowadays are not considered economically attractive, which applies to both new ore bodies and existing operations, but in a sustainable way. In order to achieve this objective, it is necessary to approach the mining business differently in five main areas: (1) operational efficiency through better use of installed equipment and skilled labor force; (2) efficient use of energy; using opportunities for alternative energy sources and efficient design; (3) efficient use of water; diminishing losses and use of seawater as an alternative source; (4) minimizing environmental impact by eliminating effluents and controlling dust emission; and (5) a more closer, proactive and collaborative relationship with the communities allowing them to be an active player in the solution to assure a sustainable business in the long term. This presentation will show how Antofagasta Minerals is facing these challenges with a long term strategy that includes all of the above mentioned aspects and that is allowing the company to exploit its mineral properties in an efficient and successful way."

Jan 1, 2014

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

By A. Lane

Africa is ripe with opportunity for the mining industry. The continent has large, and relatively unexplored mineral deposits, and recent high economic growth rates have meaningfully improved the political, economic, and infrastructural environments. However, these opportunities are accompanied by significant risks, including resource nationalism, uncertain regulation, corruption, and continuing political instability (up to and including war). Forward-looking companies actively manage these risks by creating a sense of shared purpose with the countries and communities that own the resources, using tools such as stakeholder analysis, local narratives, scenario planning, and constituency engagement. They also measure socio-economic impact to insure the creation and demonstration of shared value.

Sep 1, 2012

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By K. Ananth Krishnan

Today we see a paradigm shift in political, environmental, and economic trends, which are challenging the mining industries. It is very clear that these issues are reaching unparalleled scale and complexity. Cost efficiency and corporate social responsibility are the two primary drivers for the mining industry today. The current challenges facing the industry include: ? Due to deterioration of quality of ores, the scale of operations has become humongous which necessitates high degree of automation and remote operations ? Scarcity of skilled manpower and the necessity to minimize employment of humans at unsafe locations ? Automation of routine activities, improving the efficiency of operations and reducing the cost of production ? Land, water and energy have become scarce in most of the resource rich regions In the current macroeconomic conditions, it is obvious that the industry is under tremendous pressure and it is imperative that the industry embraces sustainability, enhanced energy efficiency, and improved resource allocation. Closely related sectors like energy and utilities have set an example by acknowledging the need to alter their business practices to meet the essentials of sustainability, adoption of new operating models, policy and regulation structures. There is a need to continuously optimize the operations across the entire process value chain as well as across geographies in order to meet the market demand while dealing with supply chain constraints. The goals of optimization could be enhancement in productivity, reduction of production costs, carbon footprint, etc. The gamut of operations is vast, starting from exploration to mining, mineral processing, smelting, refining, casting, rolling (deformation processing), heat treatment, and finally manufacturing of industrial products / components. Advances in information and communication technologies (ICT) in combination with modeling and optimization tools have made it possible to address these issues in a quantitative manner based on real life data. Manufacturing industry, for example, has successfully leveraged these technologies (ERP, PLM, MES, APC, etc.) to enhance productivity and quality. In this presentation, I would like to illustrate the benefits that could be derived by implementing ICT-leveraged solutions available today for the mining industries. I will focus on the following recent technological developments in the context of their applications in the mining and minerals industries: Mobility technologies: The industry is looking for strategically sustainable solutions that fit the working profile of mining engineers and which provide up-to-date information in real time. Mobile applications for iPhones and iPads are gaining popularity, which is helping mining engineers to work on-line as well as off-line. Mobility technologies have made it possible to provide data anywhere and anytime in a form you prescribe. This enables proactive responses to changing dynamics of the marketplace. For example, a plant engineer can access information about any critical process equipment, monitor its performance and do the needful as and when needed. Similarly, scheduling of operations can be optimized based on the market demand and on the availability of raw materials, labor, and status of equipment.

Sep 1, 2012

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is main parameter for precipitate flotation in pilot or industrial scales. The knowledge of aggregate structure can lead to better understanding and control of many solid-liquid separation processes (sedimentation, filtration, thickening and flotation). Many authors highlight the importance of structural properties (i.e. floc density) for different industrial applications.This approach was applied to achieve the flotation of molybdenum precipitate obtained with organic collector a- benzoin oxime for molar ratio 1:2. Flotation tests were carried out at lab and pilot scale with rigorous control of the size distribution of bubbles and the values of dissipation energy in the systems.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions, which were deduced from experimental data of laser sizer devices and optic microscopy pictures of precipitate. The boundary fractal dimensions Df of large aggregates allows the detection of a structural scaled organisation of the precipitate flocs (elementary germs-microflocs-flocs). The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with structuration or breakage phases.The destruction process characterised by a fractal dimension Dg controls the final size distribution. The floc destruction occurs for the lowest values of the dissipation energy (0.02 – 0.05 W/kg). The relation between Dg and the system dissipation energy Et (for various energy E dissipated in the agitation cell) involves the different breakage mechanisms of aggregates in function of the aggregation bonds (Fig. 1).Besides, the destruction of floc produces very fine particles (elementary germs or/and microfloc according to E), and thus induces the difficulties of bubble-particle attachment during the precipitate flotation in column. Yet, very small bubbles, which increase the collision probability, would make the flotation feed rate decrease. The optima ratio between superficial gas and feed velocities are determined for bubble size and flotation results control at pilot scale. Thus, it is possible to providing the catastrophically changes of precipitate column flotation by using the following established experimental relation: the mean diameter d of the flocs under the action of dissipated energy Et follows a power like law (d~Et -0.5). This allows estimating the size distribution of flocs for the E values which can appear in column."

Jan 1, 2003

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014