Search Documents

Discussions of the papers with a written contribution on Paper No. 11 and authors' written replies. Also brief obituary of Dr. T. David Jones on p146.

Jan 1, 1947

By K. C. Misra, W. Wrightson Jr.

The Lick Fork prospect shows appreciable nickel sulphide mineralization in a narrow, steeply dipping, layered sequence of metamorphosed hornblende peridotite, gahhro and hornblende gahhro, intrusive into the Pedlar Formation (charnockitic pyroxene granulite) of the Virginia Blue Ridge Complex (Precambrian). Rocks of the intrusion have equilibrated to granulite- facies metamorphism, as indicated by pervasive polygonal texture of silicate aggregates, development of biotite- and hornblende-preferred orientation, compositional equilibration of the silicate minerals, the Mg-Fe2+ (orthopyroxene-dino- pvroxene) distribution coefficients (average 0.57), (MgO + FeO + Fe20 3)/Al20 3ratios in orthopyroxenes, and Ti contents and AI(i\)/A I(\i) ratios of hornblendes. The sulphides, consisting of pyrrhotite-pentlandite (with up to 4 wt% Co)-chalcopyrite-pyrite-marcasite-violarite- bornite—mackinawite, are virtually restricted to the ultramafic unit of the intrusion and constitute 20-30% of the samples of hornblende peridotite studied. Although the basal accumulation of the sulphides may suggest magmatic segregation, sulphide- silicate textures typical of sulphide liquid immiscibilitv are not present, even in the sparsely mineralized gahbro units. On the other hand, the transgressive and relict textures are strongly suggestive of replacement of the silicate minerals by sulphides. These include chaleopyrite ± pyrrhotite ± pentlandite (violarite) ± pyrite ±magnetite veins crosscutting silicates, sulphide penetration into silicates at silicate-sulphide contact zones, rounding of silicate grains against sulphide matrix, and islands of silicate minerals (olivine, hornblende, pyroxene, biotite) in sulphide masses. Metamorphic mobilization of pre-existing sul­ phides is a possibility, but involvement of post-metamorphic, hydrothermal fluids is suggested by the following features: paucity of annealing and deformation textures in the sulphides, replacement of metamorphic and deformed silicates, lack of differential sulphide mobilization and the common occurrence of sulphides along grain boundaries and triple junctions of poly gonal silicate aggregates. The consistent association between sulphides and hydrothermal alteration products of silicates suggests that they are cogenetic. The hydrothermal fluids may have merely mobilized and concentrated the pre-existing, disseminated, magmatic sulphides, or there may have been significant addition of sulphides during this process. This question cannot be resolved unequivocally with the existing data.

Jan 1, 1984

By Z. H. Khan, A. K. Saha, D. D. Akerkar

The possibility of extracting nickel from a low-iron, highly siliceous nickel ore of Indian origin using roast reduction followed by an ammonia leaching process has been examined. The ore used in the investigation contained 0.82 wt% Ni, 6.20 wt% Fe3O4, 12.04 wt% MgO and 60 wt% SiO2. Phase changes in the constituent minerals on heating were studied by differential thermal analysis which revealed endothermic peaks at 110 and 695 degrees C and an exothermic peak at 810 degrees C. Significant process variables in studies of roast reduction include the amount of reductant, the temperature of reduction and chemical kinetics. Maximum nickel extraction was achieved by reducing the ore with 10 wt% fuel oil at 750 degrees C. The reduced ore was given a preconditioning treatment in concentrated ammonium hydroxide solution to oxidise most of the metallic iron and was then leached in aqueous ammoniacal solution at ambient temperature to dissolve nickel. This gives 88.5% extraction of nickel as soluble ammine complexes.

Jan 4, 1992

By D. J. Fray, F. Tailoka

Microporous ceramic tubes (15 micrometre pore diameter) and PVC membranes (10 micrometre diameter) have been used as spargers in the electrowinning of copper from concentrated and dilute chloride electrolytes. At a current density of 600 A/m2 and a nitrogen gas sparging flow rate (at NTP) of 1.53 cm3/s per unit electrode length, it was possible to electrowin planar rather than powdery deposits with copper concentrations as low as 0.157 M. To obtain a planar deposit at higher concentrations of cupric chloride the most realistic optimum current density appears to be between 1 000 and 1 500 A/m2.

Jan 4, 1993

By L Casari

A study of samples from three sectors of the mine, which was worked from Roman times to 1991, revealed different textures, mineral associations and distributions of trace elements in the sulphides. In the last decade before closure, grades of sphalerite concentrate were in the range 51.67-53.30% Zn and 2.21-2.86% Pb and of galena concentrate 69.43-71.62% Pb and 4.70-8.36% Zn, while the estimated by-product germanium content of sphalerite concentrates sold was 300-400 g/t. Passing the different run-of-mine materials through the same concentrator flowsheet produced middlings and tailings during the preconcentration processing. Separate and alternative treatment of run-of-mine products would have yielded improved recoveries of sphalerite and galena and better values of by-product germanium and cadmium

Jun 18, 1905

By F. Boudreault, M. J. Scobie, J. Szymanski, C. Hendricks

The development of new stoping methods and more effective control over dilution, recovery and fragmentation depends on improved accuracy in blasthole drilling. The mechanisms and factors which control accuracy are poorly understood. Canadian blasthole stoping and the practices adopted for monitoring and controlling drilling accuracy are reviewed. The techniques and problems associated with blashole set-up and trajectory surveying are discussed. Four new blasthole trajectory survey systems are evaluated on the basis of their performance in recent underground trials. Conclusions are drawn as to the technological developments required so that more precise control over drilling accuracy can be achieved.

Jan 12, 1992

By K. M. Kinealy, A. R. Ramsden, D. H. French

A negative correlation exists between sphalerite composition and gold content when gold is transported as Au(HS)2(-); however, there are spatial and temporal differences within a single deposit. A previous model for the formation of volcanogenic massive-sulphide deposits within thermally intensifying and waning hydrothermal sytems in much the same way as is observed around modern sea-floor vents is supported. The results also emphasise that recognition of the mechanisms of gold transport in ancient deposits depends critically on an understanding of their mineralogy and stratigraphy

Jan 1, 1991

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By Z. Sawlowicz

Finely dispersed, primary sulphide mineralisation in the Cu-Fe sulphide zones of copper-bearing shale of the Polish part of the Permian Kupferschiefer is mainly present in the form of framboids and spherules. This type of mineralisation is especially well preserved in organic-rich shale, where it often dominates over a later diagenetic mineralisation that consists of large grains and veins. In microscopic observations special attention was paid to composite grains of copper and iron sulphides. The results suggest that the Cu-Fe and Cu sulphides precipitated in the Kupferschiefer sediment before pyritisation of the framboids had ceased and that they replaced metastable precursors of pyrite. The precipitation of copper sulphides could have been delayed owing to the formation of Cu-organic complexes.

Jan 4, 1992

By M. Dobias, N. Mayor, J. Lillo, A. Gonzalez, R. Lunar, R. Oyarzun

The central domain of the Spanish Central System contains a series of Ba-(F)-(base metal sulphide) hydrothermal vein deposits that are hosted by adamellitic granitoids. Fluid inclusion and sulphur isotope data suggest that the mineralisation was formed by low-salinity hydrothermal solutions that incorporated fluids, metals and sulphur from a magmatic source. Mineralisation occurred in two main stages; a first stage of open-space filling with quartz-Ba-(F)-(base metals) ; and a second stage of brecciation and deposition of quartz-barite. The two mineralising events can be clearly related to two tectonic episodes of late Variscan age that involved extension along east-west trends followed by ductile transcurrent movements along northeast-southwest trends.

Jan 4, 1992

By H. L. Willett

Wrapping up the symposium, covers incidence of spontaneous combustion in British mines, assessment of liability to spontaneous combustion, precautions, rate of advance, starting a line of a coalface, local heatings at roadsides, burying packs, coal headings, retreating longwall, detection and sealant coatings.

May 23, 1905

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By E. H. W. Hornbrook, P. W. B. Friske

Paper presented at the 28th International Geological Congress, Washington DC, July 1989 (International geochemical mapping sessions). The objective of the programme is to establish and maintain a nationally consistent geochemical drainage database. Towards this end systematic surveys have been conducted since 1973. To date more than 200 surveys have been completed to the required standards, representing 180 000 sites and covering about 2 100 000 km2 throughout Canada

Jun 13, 1905

"Prior to the publication of the General Report of the Miners' Phthisis Prevention Committee of South Africa in 1916 little attention was paid to the dust hazard and the necessity for its suppression in the underground workings of the Broken Hill mines. Such precautions as were observed for the elimination of dust were related rather to the prevention of lead poisoning, which, in the early days of Broken Hill when large tonnages of lead carbonate ore were being won, was rather prevalent. Ventilation and hygiene followed the general practice in this and most foreign countries.This paper covers incidence and action since 1918, considering medical aspects and operating aspects. "

Jan 1, 1947

Two of the most important economies in coal-washing are in the actual washing of the coal and in a proper lay-out to reduce to a minimum the cost of labour for handling and washing. A guarantee is usually required for turning out a washed coal containing not more than 2% of free dirt and a resulting refuse with not more than 2% of free coal; any plant that gives results within such guarantees can he considered economical, provided that there are no other losses during the washing process. Various drainage arrangements and washery lay-outs are illustrated and discussed with respect to drainage, bunkers, sieves, settling tanks and conveyors and two further points considered: siding accommodation, which may become quite important with washeries of large capacity especially when the coal is brought in railway-wagons; and the irregularity with which the coal arrives. (Paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair)

Dec 1, 1916

By R. Immele-Meziou, G. J. Long, D. G. C. Robertson, O. A. Pringle

The reduction of naturally weathered ilmenite concentrate occurs in two steps: reduction of Fe3+ to Fe2+, followed by reduction of Fe2+ to Fe. Small amounts of a magnetic phase were also observed and may correspond either to an Fe3O4-FeTiO3 ilmenite phase or to an Fe3O4-Fe2TiO4 spinel phase. The total amount of metallic iron produced after 12 hr was only 50% of the total iron present in the sample.

Jan 4, 1992

By Ruddle R. W.

The slags produced in copper smelting are largely composed of silica and ferrous oxide and may therefore be regarded as essentially ferrous silicates. A fair amount of information is available on the constitutions of the liquid slags used in copper smelting and, in this connection, the large volume of work being carried out on steelmaking slags should be helpful. Constitutional diagrams are available for most of the principal systems involved (SiO2-FeO; SiO2-FeO-Al2O 3; SiO2-FeO-CaO; SiO2-FeO- MgO; and SiO2-FeO-CaO-Al2O3) and these show that additions of Al2O3 and CaO reduce the freezing points of SiO2-FeO slags but that additions of MgO increase the freezing point. A certain amount of information is available on the thermodynamics of slags, but much further work on this subject is required. Modern theories of the constitution of liquid slags deny the existence of molecular compounds but consider that liquid slags are mixtures of various ions such as, Fe2+. O2- and SiO4(4-). Little appears to be known of the reactions between matte and minor constituents dissolved in the slag

Jan 1, 1953

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953