Search Documents

By Curtis G. Kremer, Jeffrey L. Brummert

Blue Circle Cement's Ravena, New York quarry mines approximately 6.7 million tons of limestone per year. Blasting occurs approximately twice a week on three separate benches. Shots average 60,000 tons but can range up to 140,000 tons. Ongoing scrutiny of the drilling and blasting program allows for maximum blast efficiency which results in lower overall mining and crushing costs. Close cooperation between management and explosives supplier assures Blue Circle Cement's objective, "To develop, implement, and continuously improve a measurable drilling and blasting system that will optimize the total mining and crushing costs while ensuring compliance to safety and maintaining or reducing the environmental impacts of blasting".

Jan 1, 1994

By Shad M. Sargand, Glenn A. Hazen, A M. M Jayasuriya

Various types of waves originate from a blast source to propagate through rock/soil media away from the blast. Input vibration to a structure depends on the soil-structure interaction which varies with the dynamic properties at the intersection as well as the stress and strain levels developed from the vibration of the structure-ground system. Hence it is important to study such effects on the response of a structure due to blast loads and this knowledge can be used in the design and control of blasts that are carried out close to buildings, highways and other structures.

Jan 1, 1994

By Lyall Workman, P D. Katsabanis

Energy released by the explosive is typically partitioned in brisance, heave and losses. The fact that energy released in the P-V expansion curve below a certain point is lost has resulted in the concept of available energy. Through simple calculations it is shown that energy released at pressure levels thought to be low, amounts to a significant proportion of the total energy value. Furthermore, throw calculations indicate that the assumed loss of that part of energy does not justify practical results. Loss of energy at the low pressure levels may also not be justified from the fragmentation point of view as pressure levels below 1 kbar are enough to extend radial fractures around a borehole. Finally the equation used for the P-V behaviour of the explosive gases is important in throw calculations. Simplified approaches may not reproduce the performance of the explosive which is not characterized only by its energy content.

Jan 1, 1998

By C. Partouche, T. Bernard

Blasting engineers are mainly concerned about fragmentation issues. Even further, this is the final goal of using explosives. A lot of models have been developed for controlling fragmentation distribution, but most of the time, they are based on physical phenomena using field data as input for rock characteristics. Fragmentation is a result of two phenomena: waves from the borehole, damaging and cracking the rock, and gas pressure, widening those cracks and spreading out rock fragments. This model simulates the P wave escaping from boreholes and the cracks created by these P waves. It takes into account rock characteristics, provided by digital imaging, and explosive characteristics coming from VOD measurements. What we need to focus on, is the interaction of P waves coming from each borehole related to different timing sequences. This paper presents several simulations that show the influence of the timing and the sequence accuracy on the fragmentation distribution.

Jan 1, 2002

By TA Louw, Dr CM Lownds

In an era where profits are constantly being eroded, mines are looking towards technology developments to assist them in solving mining problems and reducing mining costs. An emerging technology that could assist mines in becoming more cost effective is electronic detonators. Electronic detonators have been under development for several years. Over the past three years, the spotlight has fallen on commercial use of electronic detonators and the extent to which the promise of precise and programmable timing can assist mines with their environmental and productivity problems. This paper uses case studies to demonstrate both surface and underground applications where electronic detonators and blasting systems were used to solve typical mining problems such as vibration and fragmentation. Safety aspects such as hanging wall conditions and high wall stability also benefited from the use of electronic detonators. The paper also demonstrates how the use of accurate electronic detonators and blasting systems has resulted in improved/more even fragmentation with further downstream efficiencies. These efficiencies may include increased cast percentages, reduced oversized rocks, quicker cleaning times and increased production rates.

Jan 1, 2004

By Claude Cunningham

AEL has been developing electronic detonators continuously since 1986. It launched its first system for opencast mining in 1993, and now has two distinct product lines. The path has not been without great difficulty, but the determination to persevere was always buoyed by the strong encouragement of customers who experienced the transformed blasting results, as well as a clear vision of the enormous intrinsic value of the concept. The path of growth to dominant global supplier is traced through the separate application channels of coal stripping, quarrying, massive mining, opencast mining and narrow reef mining, to the first allelectronic detonator demolition blast in June 2001. Reasons for the slow coming to market of this highly desirable concept, which often coincide with reasons for the demise of various other systems, include the difficulty of safely mating electronics and explosives in a low cost environment; the extreme difficulties of achieving proper connection under mining conditions; the rapid rate of evolution of the technology, and the safety concerns raised by various accidents and incidents along the way. ED.s are now established as the way forward and are set to displace other systems in all serious applications. There is place for both programmable and pre-set delay systems.

Jan 1, 2002

By Robin L. Simmons

Mining in the Genesis open pit has been conducted above the active haulage and ventilation declines of the Deep Star underground mine. Production has continued in both mines. The Deep Star haulage and ventilation declines, the primary and secondary egresses respectively, had to remain open and safe for travel until the new haulage and ventilation accesses were completed. Eventually, the upper 350 feet in each decline will be removed. The declines are in relatively competent calc-silicate hornfels with several high-angle, northeast-striking, clay-filled or open-spaced fault zones that create localized areas of poor ground requiring steel sets. To maintain the integrity of the declines, blast-induced vibration levels and damage were monitored in both declines after each surface blast. Seven geophones were installed in the declines to monitor peak particle velocity and peak vibration frequency. These data helped design subsequent blasts and predict expected vibration and damage levels. Blast design modifications included reducing the pattern size, reducing the powder factor and limiting blasthole detonations per delay. While limiting blast-induced vibration, these blast design modifications had to allow effective surface mining to continue. Linear regression analysis of peak particle velocity and scaled distance was used to determine the scaled distance necessary to keep the peak particle velocity under 2 inches per second. To date, the new ventilation raise, which is also the secondary escapeway, has been established and safe conditions were maintained in the original ventilation decline. Data collection and conscientious blasting procedures continue above the haulage decline.

Jan 1, 1998

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Serdar Celik, Yucel Karakus

This paper presents bench blasting designs based on results of vibrations analysis on test shots organized in an open pit coal mine located near to Soma district at Manisa province in Turkey. There are some structures which can be adversely affected by blasting at the coal mine. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting at these structures by risk analysis based on ground vibration measurements. During this investigation, the data pairs of scaled distance and particle velocity obtained from the 36 event records belong to 9 test shots were statistically analyzed and a PPV prediction equation specific to this site with 95% prediction line were obtained. And also, this equation was used in the derivation of the practical blasting charts specific to this site as a practical way of predicting the peak particle velocity and maximum charge per delay for future blasting. A risk analysis was performed by using this equation. In the light of this analysis, preliminary blast design model was proposed to be used in this coal mine for overburden excavation.

Jan 1, 2012

By Dr. Tristan Worsey, Dr. Jhon Silva-Castro

Confinement is an important aspect of blasting. Reducing and increasing confinement can determine whether a blast design performs properly. Over-confined shots usually have poor fragmentation, higher vibrations, and stemming ejection, and unconfined shots usually have a lot of air blast and fly rock. When talking about confinement in blasting, static confinement conditions are typically referenced. Static confinement conditions are ruled by free faces, shot muck, burden, spacing, stemming, hole depth, toe, etc. All these conditions exist in a static state. Static confinement conditions are generally analyzed before the shot takes place, but once the shot starts, the conditions will change according to the sequence and delay of the shot. Once the shot starts, Dynamic confinement takes place. For the authors, Dynamic confinement is the confinement conditions that exist for the charge when it fires and should account not only for the variables included for the static confinement but also for the time and sequence of the shot. The paper explores the theory of dynamic confinement and its role in influencing blast performance. Time and sequence are the main influencers of dynamic confinement and will be the focus of the paper. How to generate the appropriate timing based on blast design, dynamic confinement, static confinement, and geology will also be discussed.

Jan 21, 2025

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By Rick Lamkie

When investigating citizen complaints about blast vibration and airblast, it is important to be able to establish the spatial relationships between blasts, blasting seismographs monitoring the events, and complainant structures to assess any directional impacts. The Pennsylvania Department of Environmental Protection (DEP) routinely uses hand-held GPS receivers to document these relationships. The waypoint (structures and seismograph monitoring locations) and tracking (blasting and permit areas) features are used to map a site. These data are imported into the software for editing and conversion to GPS Exchange (.gpx) format.

Jan 1, 2008

By James E. Jr Hargroves

With the ever-increasing population growth and modern trend to urban development, the expansion of utilities is a stable, mad or, and constant source of income for many. Blasting is a "necessary evil" to the utility contractor. It can make or break even the most solvent. Housing development expansion and higher treatment of effluents are causing utilities to appear in more congested areas. This paper discusses some of the aspects of utility blasting in the State of Virginia. Consideration is given to bid procedures, pre-blast surveys, record-keeping and practical application.

Jan 1, 1977

By Alain Duchesne, Dominique Fonfrede, Alan Broca

The technique involves the removal, in one piece, of an unwanted concrete pile section, exploiting the principle of crack propagation induced using gas pressure. The device, or pod, is made of a container in which an over-pressure is generated. After a predetermined time delay of 72 hours, gas and pressure are produced by the reaction between a calcium base chemical and water.

Jan 1, 2012

By Calvin Konya, Theodore R. Myers, Robert Lundquist

The design of a single, large mass blast using ring drilling may take two to three months. This time requirement inhibits the evaluation of multiple designs. It also reduces the flexibility to redesign a blast when a parameter affecting the blast changes. Manual preparation exposes the design of a ring blast to a greater probability of human error. The use of Computer Aided Design (CAD) can help to overcome the shortcomings of manual design preparation. High speed electronic calculation, as well as programming, allow for many designs to be considered before blasting. Parametric programming allows single or multiple parameter changes to be introduced into an existing design, such as changes in drilling equipment, variations in ore density or changes in explosive. Exposure to human error is reduced by programming that performs calculations and produces graphical displays for review by the designing engineer. The goal of achieving desirable fragmentation for the minimum cost, when using ring blasting, is obtainable using blasting design techniques and CAD. Multiple designs can quickly be generated and costed, producing cost curves that indicate an optimum design with respect to cost.

Jan 1, 1990

By Evan Boone, Peter Bellairs

A technical services visit was conducted to determine the initial parameters to successfully presplit several benches for an input crusher installation at the Wolffdene quarry. The paper details the preliminary design utilising both detonating cord only and specialised presplit product charges and compares these to the final designs utilised based on site experience. The role of accurate drilling, explosive loading and geology in obtaining successful cost effective presplits is highlighted.

Jan 1, 1998

By Claude Cunningham

Blasthole pressure is the starting point for many blast design calculations, but the way in which it is usually derived, from measured detonation velocity, indicates that more thought is needed as to its true meaning and implication. The general impression is given that the energy in the hole is defined by VoD, but rarely is this the case. VoD is defined by the energy released in the Detonation Driving Zone between the shock front and the Sonic (or 'CJ') surface, and for commercial explosives it is normal for reaction not to be complete within this zone. Reaction and energy delivery continues behind it, not reflected by VoD. Thus it would be more appropriate to use the theoretical VoD, not the measured VoD, to derive the starting pressure, since this would reflect the energy input of full reaction. In decoupled situations, the derivation of pressure at the blasthole wall using a polynomial decay concept is also of debatable value, and an alternative is offered.

Jan 1, 2006

By Joshua Hoffman, Philip Mulligan, Braden Lusk, Tristan Worsey

Blasters rely upon detonators to achieve the designed timing sequence to move material where it needs to go, minimize vibration, or optimize fragmentation. At times detonator inventory on seldom used delays may be slow moving. This can lead to detonators being used long after they were manufactured. This paper addresses the potential shelf life concern as it relates to timing accuracy of shock tube detonators. A recent study was conducted to study the timing accuracy of non electric shock tube detonator systems. A follow up study was then conducted to determine the degradation of the non electric shock tube systems accuracy with time. The follow up study is presented in this paper. Samples of detonators from the initial study were set aside for approximately one year and then tested. The results from the aged detonators were compared to those of the detonators that were tested in the original study. As an extreme case a third set of shock tube detonators was tested using detonators that were between eight and nine years old. The results from these tests are presented as well. Each system was tested at a short medium and long delay time. Statistical analysis was conducted to determine the effect of time on the detonators accuracy. This paper quantifies the importance of regular inventory cycling to help preserve manufactured timing when using non electric shock tube detonator systems.

Jan 1, 2013

By J T. Keim

Members and guests of the Society of Explosive Engineers, it's indeed a pleasure for a longtime practical user such as myself to have the ears of so many explosive experts for a few minutes just to express my feelings and concerns on blasting as well as the feelings and concerns of many other users and operators.

Jan 1, 1978