Search Documents

By James Ludwiczak

This paper consists of the conduct of a forensic criminal investigation of the components, construction, use, and functioning of two suicide bombs. As the title states, the task was to form professional opinions as to whether the bombs would work, would cause property damage, and would injure or kill. The bombs were created and installed by a defendant in a Federal death penalty case where the defendant’s daughter was killed in a shootout with the West Virginia State Police. The two black powder bombs were placed under the front seats of the defendant’s automobile and were designed to function by the use of a toggle switch connected to the automobile’s cigarette lighter. The forensic work first consisted of an inspection of the remains of the wiring system and bombs at the Bureau of Alcohol, Tobacco, and Firearms Laboratory, in Ammendale, MD. This was necessary to determine and detail the wire diameter and lengths, the lengths and size of the wire used, the type of toggle switch used, the type of containers, the type of rocket motors used to initiate the black powder, the manufacturer and amount of black powder used in each bomb, and the type, wraps, and amount of duct tape used for the construction of each bomb. Using this data, tests were conducted by duplicating the wiring system and the two bombs to insure that the system functioned properly. Each bomb was duplicated and initiated to observe the violence produced when initiated in the open air. Duplicate bombs were placed under the seats of a similar type of automobile and initiated. The purposes of the tests were to duplicate the bombs, to observe the violence of the initiation, and to observe the damages to the automobile produced by the initiation.

Jan 1, 2007

By Fumihiko Sumiya, Yukio Kato, Yoshikazu Hirosaki

Secluential blasting is one of the most popular methods in blasting. tiowever, it is well known that an emulsion explosive can be dead-pressed by dynamic pressure generated by the previous detonation. It is difficult to gain the expected blasting performance due to tb.e malfunction of explosive caused by deadpressing and shock desensitization. Such malfunction of an explosive is undesirable for safety blasting operation. Voids in the emulsion explosives will considerably affect the performance of explosives such as sensitivity, detonation velocity (DV), pressure-resistance and so on. To clarify the detonability and the performance of precompressed emulsion explosives, the DV was measured. Three types of microballoon or micro bubble ; two types of glass microballoon(GMB), resin microballoon@MB) and chemical gas bubble ; were used as sensitizers for the sample emulsion expiosives. The underwater explosion test was carried out to load dynamic pressure into the sample explosives. The dynamic pressure was generated by the detonation of a donor explosive, and the DV of the sample explosives as acceptor was measured by ionized gap terminals. The dynamic pressure level and initiation interval for the donor and the acceptor were chosen as experimental factors. The detonability was carefully investigated at short initiation intervals taking into consideration the interaction between same delays caused by the deviation of the ignition time of the electric detonators. From these experiments, the following results were obtained ; A) The DV of precompressed emulsion explosives was low compared with that of uncompressed emulsion explosives in all pressure conditions. B) The decrease of DV in the sample explosives sensitized by GMB s was larger than that of DV in the sample explosives sensitized by RMBs or chemical gas bubbles. C) The recovery of the detonability occurred rapidly in the sample explosives sensitized by RMBs and chemical gas bubbles. However, a long period was needed for the recovery of detonability in the sample explosives sensitized by GME! s. It was concluded that the type of microballoon and micro bubble significantly influenced the detonability of precompressed emulsion explosives.

Jan 1, 2002

Hello, everyone. Way back in 1965, Devine and others at the US Bureau of Mines showed that a presplit fracture plane did not affect vibration levels transmitted across the plane (RI 6695).

Jan 1, 2010

By Richard N. Snyder

In this system for connecting blasting caps to the initiation source, the need for a redundant design structure provides more reliable method of explosive initiation. This is accomplished by using a complete system starting at the blasting control, through the initiation line structure through the initiation line and connecting blocks to the blasting cap. The connecting structure between the initiation device and the blasting caps may be connecting blocks or other means.

Jan 1, 1995

By Roger L. Keller

This paper examines the aspects of differing types of blasting cuts in underground headings with consideration to the reduction of number of holes and costs. At least one comparison study is related where costs per advance meter were significantly improved. The technical aspect of the paper covers a study of the effects of various blasthole delay intervals on resulting crater volume, ground vibration, and fragmentation for six hole V-cuts.

Jan 1, 1989

By M Scoble, J Szymans

During the past year, the Canadian Centre for Automation and Robotics in Mining (CCARM), McGill University, Montreal, has been involved with INCO Ltd.'s Manitoba Division in investigating the extent and mechanisms of blasthole deviation. Drilling accuracy can well be regarded as perhaps the single greatest "controllable" factor influencing dilution in INCO's open sloping operations. As INCO and other underground mines seek to minimize dilution, while attempting to maximize productivity, issues of drilling accuracy become increasingly significant. It is important therefore, that means exist by which true blasthole trajectories can be determined, so that if needed, modifications to hole loading instructions or redrilling of holes can be ordered, thus avoiding poor blast results.

Jan 1, 1991

By Paul Worsey, Larry Kenchel, David Randall, Mark Schmidt

The University of Missouri-Rolla (UMR) has historically maintained a manual, paper inventory of explosives stored and used at the university. Although this system was accurate for inventory control and reporting criteria, it was labor intense and delays in record keeping were predominant. A directive from the university’s administration mandated the development of a precise real time system “on-line” to maintain and control the explosives inventory in line with the universities new chemical tracking policies.

Jan 1, 2001

This is the story of a blast - not a large blast by todays standards as it only involved a total of approximately 50 cubic yards of rock. Nor did this blast involve any new or revolutionary blasting technique or require involved analysis or the applications of rock mechanics theories. Instead, it was a blast that involved the tried-and-true principles of good blasting: precise alignment of blastholes; selection of explosives and detonators designed for the conditions encountered; extreme care in loading and hooking up and the use of several ingenious devices and techniques to achieve the proper loading and firing of the blast

Jan 1, 1976

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By MSHA website

“Conditions at underground and surface coal mines can change dramatically during the winter months,” said Joseph A. Main, assistant secretary of labor for mine safety and health. “We must be ever mindful of the seasonal changes that can affect our work environments.”

Jan 1, 2011

By Vincent Thorne

On January 2, 1992, the R. Zoppo Company of Stoughton, Massachusetts started drilling and blasting operations on U.S. Army Corps of Engineers Project Number: DACW33-91-B-0072 to widen and deepen the Portsmouth Harbor and Piscataqua River Navigation Channel.

Jan 1, 1993

By David E. Siskind

"This report describes recommended vibration monitoring and assessment practices at blasting sites.Intended is regular monitoring, tracking of trends, responding to complaints of alleged damage, and the technical and data aspects of addressing lawsuits."

Jan 1, 1999

By Isaac E. "Chip" Harris

A general understanding is given to how and where blast hole drills are used and what recent developments have taken place with small and large diameter drill hole machines. Indications are that new developments with high penetration rates and large diameter holes are not necessarily the answer to increased production in the field.

Jan 1, 1979

By R. K. Wharton, G. H. Pickering

The paper reviews the explosives products that have been certified by the different Explosives Notified Bodies for sale in European Union countries. The development of harmonised standards for explosives is also discussed as are recent developments relating to certification and a possible forthcoming Directive on pyrotechnic articles.Copyright

Jan 1, 2004

By Ron Fish, Cherokee Stone

Drilling and blasting in open pits is very unique in Southern Florida. Crushed limestone, the state's most abundant mineral resource, is retrieved from the bottoms of huge open pits that are completely inundated with fresh water. It is this industry that makes southern Florida the fastest growing area in the United States.

Jan 1, 1986

By M Dale White

Captive insurance companies have recently been discovered by risk management experts as a risk transfer vehicle and are very much in vogue. Actually, captive insurance companies are not a new phenomenon. Centuries ago, the first insurance organizations were what we today refer to as group or association captives. Early traders banded together to share the risks of ocean shipments writing ocean cargo coverage, the oldest form of insurance.

Jan 1, 1980

By Charles A. Nork

Licensing of surface blasters as a regulatory requirement has been in effect in Pennsylvania for more than twenty years. Training of license applicants was begun in 1971 on a random basis. Formalization of training of applicants for surface blaster licenses was begun in 1980. Training is conducted on a regularly scheduled basis in specific locations throughout Pennsylvania. Training is conducted by Charles A. Nork with the assistance of one of five Department explosives field inspectors.

Jan 1, 1985

By Li Jianjun, Zhang Xiaozhi, Guan Li, Jin Jinzhe

People used to regard emulsion explosives as the safest industrial explosives. But in the process of manufacturing emulsion explosives spontaneous ignitions of the remnant emulsion matrix have happened under the conditions of constant or low temperature. These fatal accidents show both emulsion explosives and emulsion matrix may involve hidden danger. Since the temperature in its production emulsion matrix is high, emulsion matrix is sensitive to mechanic action.

Jan 1, 1998

By Shad M. Sargand, Manseok Chang, Glenn A. Hazen

Customarily, peak particle velocity of surface wave vibrations has been the recommended criterion for the prediction of blast damage to structures. Currently blast spectrum and natural frequencies of a structure have been also recognized as important for predicting damage potential. While others have considered the importance of structural frequencies, they have not analyzed the structural response spectrum when establishing damage criteria.

Jan 1, 1992

Prediction of fragmentation in Taconite Mining is an important aid to blasting engineers. A simple theory relates the intensity of radial fracture per unit length to distance from the borehole, from which a power law for mass fraction passing versus size is derived. For the lower end of the size distribution, the equation agrees well with several published examples of fragmentation from sieving of full scale blasts. Large size fragments arise from interaction of fractures from neighboring holes and pre-existing joints. Analysis of two assumptions regarding radial fracture interaction shows that complex fragmentation distributions can arise from the simple mechanisms proposed. Measured fragmentation falls between the two extremes calculated.

Jan 1, 1996