Search Documents

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By W. Reisz

The fear of heights is a natural defense against performing a dangerous and unnatural act such as standing on the edge of a hundred foot wall. Yet through familiarity, a casual attitude often exists. Those of us, who work near highwalls on a daily basis, may become overly comfortable in our surroundings, losing sight of the disaster which may often rest a single misstep away. And this is where the hidden dangers lie.

Jan 1, 2009

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Jim Breedlove, Stephen P. Case, Mike Fabio

To meet salt production needs over the remaining life of the Cayuga Mine at Lansing, New York, the Salt Division of Cargill, Inc. decided to build a new underground screening plant. The new plant required a chamber 50 feet wide by 250 feet long and nearly 70 feet high. On advice of their mining contractor, Dynatec Mining Company, the company chose an ingenious excavation method similar to sublevel stoping. This method eliminated the need for an access ramp, reduced equipment needs and excavation time substantially.

Jan 1, 1996

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By Shazad Hosein, Bill Birch, Catherine Johnson, Toby White, Liam Bermingham

Air overpressure (AOP) from blasting can give rise to a significant number of blasting complaints from residents living adjacent to blasting operations from mines, quarries or civil engineering projects. High amplitudes of AOP are usually associated with the lateral movement of a vertical free face, but it can also be caused by the upward lifting and the venting of gases through the surface of the blast area.

Jan 1, 2018

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By T Barnes, K D. Sexton, T J. Tope

For the past decade, the U.S. Department of Defense (DoD) has been under increasing pressure from state and federal regulatory authorities to develop management strategies for waste streams generated at its bases, installations, and ranges. Since passage of the Federal Facilities Compliance Act (FFCA) in 1992, concerns have focused in particular on military munitions and energetic waste streams.

Jan 1, 1997

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By Rolf R. Schillinger

Subject of the paper are blasting vibrations as sources of environmental molestations including acceptance level,complaint level and damage level as well. Besides, the subject shows a comparison of international regulations and their problematical aspects. In consideration of blast induced immissions the subject shows that human annoyance has become an important place in blasting works. It provides a solution proposal how to minimize environmental effects of blasting works.

Jan 1, 1996

By Nolan Eckroade

The demand for blast optimization within the quarrying industry calls for more effective, faster and safer methods of quantification of blast performance. Drones provide the ability to safely and quickly capture high resolution imagery of a muckpile for use in fragmentation photo analysis. Oversize material within a muckpile is an expensive and universal problem affecting quarries, especially in situations where cap rock is present. Although the amount of oversize material in a blast is a key indicator of blast performance, it is difficult, hazardous and slow to measure across an entire muckpile using traditional methods. By piloting a drone using an automated flight plan with set amount of overlap across images, the images can be processed into a single, high resolution orthomosaic image for use in fragmentation photo analysis software.

Jan 1, 2018

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Y Nagendra, A. Ravi Kumar

A breakwater is a construction for protecting the marine structures like port, harbor, or anchorage-basin and berthed marine vessels from the destructive influence of the sea waves. The breakwater is constructed by using geologically competent, heavy, massive rock like granite, basalt etc having physical and mechanical properties within the limits specified by the designers. The construction requires boulders in varying sizes ranging from 0.5 kg to 20,000 kg. The stones from 0.5 to 1000 kg are called as core fill and boulders greater than 1000 kg are termed as armor blocks. These armor blocks cover and protect the core fill and prevent it from escaping. The requirement of armor blocks ranges between 25 to 35 %. The rest is core fill. However, the actual requirement depends on the breakwater design. In this context, the task of the mining engineer is to economically produce armor blocks and core from the designated quarry in right proportion with minimal losses. The whole bunch of engineering ingenuities should be put forth for obtaining the required armor blocks. The armor block production from any blast depends chiefly on geological conditions, bench dimensions and blast design. This paper is an attempt to bring out the various parameters affecting the performance of the blasting for armor block production using a case study.

Jan 1, 2005

By Eduardo Lozano, Vilem Petr

This study demonstrates the ability of high-order, shock-capturing methods to simulate detonation wave propagation in right circular cylinders of non-ideal explosives. 2-D axisymmetric, reactive Euler equations were solved for the detonation of the highly non-ideal explosive ammonium nitrate-fuel oil (ANFO) using a simple pressure-dependent rate law and perfect gas equation of state. The fractional step method was applied to the convection and reaction operators using a 2nd-order Strang splitting. The flow solver consisted of a finite difference scheme where the flux is reconstructed by a modified fifth-order weighted essentially non-oscillatory (WENO5-Z) with local characteristic decomposition and local Lax-Friedrichs (LLF) flux splitting. Time integration was performed by a third order total variation diminishing (TVD) Runge-Kutta time discretization method, also known as the strong stability preserving (SSP) method

Jan 1, 2019

By Joseph Haid, om, Rio Yang, Kelly Fleetwood

Some coal mining operations in the Powder River Basin are currently observing a number of blast holes detonating sympathetically within their cast blasts. Sympathetic detonation can cause poor cast results, high blast vibration levels, excessive back break and fly rock, along with a number of other undesirable blast results. The reduction or the total elimination of blast hole sympathetic detonation is of paramount importance to the coal mining companies operating in the Powder River Basin. This paper describes a systematic approach to prevent cast blast holes from detonating sympathetically through the use of the electronic initiation and expanded blast patterns. In-situ measurements outlined in this paper were recorded from pressure probes, velocity of detonation probes and near field accelerometers, along with digital images generated from a high speed CCD camera. Large diameter angled drill holes were also checked for any measurable amount of deviation by a cable type borehole measurement tool. The field measurements provided the scientific evidence, statistical data, and documentation necessary to develop a sound method or a “road map” that would minimize and in some situations prevent the occurrence of blast hole sympathetic detonation.

Jan 1, 2005

By Duan Baofu, Wang Xuguang, Song Jinquan

In this paper, the model of optimizing selection on preparation of Powdery Emulsion Explosives(PEE) is established by the Neural Net Theory(NNT). On the basis of some data in the study of PEE, the training, prediction and optimizing selection of the Neural Net (NN) model are finished by a compiling procedure. The results indicate that the model is helpful to the preparation of PEE and worthy to extend and apply broadly. KTYWORDS Neural Net Powdery Emulsion Explosives Preparation Optimizing Selection

Jan 1, 2003

By Elliott A. Pood, Ron Gilbert

Recent advances in digital recording technology have allowed frame rate increases in video recording equipment that provide the capability for super slow motion playback of commercial explosives shots. Such slow motion playback allows for the analysis of shot patterns, cap scatter, pattern failures, etc. In addition, the availability of such materials on video tape enables commercial blasters to provide a means for training current and future staff.

Jan 1, 1996

By B R. Spencer

Using bulk repumpable water gel explosives in underwater shooting results in even more benefits to the user than a "dryland" customer. It is nearly impossible to reshoot underwater, so a bad shot causes tremendous problems. The huge expense of operating drill boats, dredging buckets and clamshells makes shot loading, hookup and digging cycle times critically important.

Jan 1, 1990

By Mark S. Rayson, Jessy Lee, David O. Johnson, Matthew R. Rawls

The ability to manipulate the structure of liquid chemicals in an explosive is important in mining applications, where precision blasting is crucial for the safe, reliable, economical and eco-friendly extraction of ores. Static mixers allow explosives, emulsion-based in particular, to be custom-made as they offer precise and reproducible mixing without the need for moving mechanical parts. In this paper, we perform numerical simulations on the laminar mixing of two nitrate-based fluids in a Kenics static mixer unit for various mixer parameters. Two numerical methods were investigated in the study of the mixing pattern: solving the mass transfer equation and using particle tracking. The former introduces artificial numerical diffusion which can lead to spurious smearing of the component boundaries, a problem that can be avoided with the latter technique. We have also demonstrated that the particle tracing method is capable of qualitatively predicting the blending patterns under the conditions studied.

Jan 1, 2014

By James Goldberg, Sally Zadra, Wiliam Reisz

Early recognition and risk assessment is critical to sustaining a safe and productive blasting operation. While every blasting environment holds inherent risk, highwall blasting in highly congested areas such as Hanson Material Service Corporation’s Romeoville and Thornton quarries in the greater south Chicago metropolitan area can be particularly perilous

Jan 1, 2008