Search Documents

By Alan Bauer

During the past several years, the trend to large-diameter blastholes in both open pits and underground mines along with the continuing developments in slurried explosives and delay systems has kept things exciting for the drilling and blasting engineer. This has been particularly so in underground mining, where new mining systems having lower cost and higher productivity have emerged. Crater technology has produced new large-scale methods for resisting front penetration in tar sand mining and also new underground retreat mining methods and methods of raising.

Jan 1, 1978

By Michael J. Sapko, Eric S. Weiss

The U.S. Bureau of Mines has been conducting research on the secondary explosion hazards associated with the mining of oil shale under gassy mine conditions. Explosive incendivity tests have been conducted in a 28 m~3 (1000 ft~3) gallery to evaluate the relative incendivity of experimental emulsion-ANFO blends. The incendivity was measured by determining the minimum inert stemming requirements for preventing the ignition of a methane-air atmosphere by the discharge of hot detonation products from a 5.7 cm (2.25 in) diameter borehole.

Jan 1, 1990

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

The basic metric for linear shaped charge performance is the amount of cutting distance that the charge can effectively yield given a specific standoff and target. Due to its size and restricted production runs the 10,500 grain/foot (2,232.25 grams/meter) linear shaped charge has had only limited studies that examine cutting performance and standoff. This article covers research regarding cutting performance verses standoff as the charge is applied to common structural steel. Specifically this study uses A36 mild carbon structural steel blocks of 10.16 cm by 11.80 cm by 35.56 cm and standoff distances of 0.5, 1.0, 1.5, and 2.0 charge diameters. Data presented includes the presentation of actual cutting performance numbers, comparison of that data to projected performance based on currently recognized industry guidelines, and a discussion of what may contribute to the performance found in this study.

Jan 1, 2013

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Victor Munoz, Jorge Oliva, Gonzalo Marias

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth.

Jan 1, 2019

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By Zhang Yangde

"This paper reports the clinical research work of Micro-explosion of Biliary Calculi . In theprogram the technique of directional micro explosion applied to disintegrate the biliarycalculi of body and decreases the rate of operation. Up to the present, 235 cases of biliaryduct calculi have been successfully treated by use of implusive force of micro-explosion .The success rate of blasting stones was 100% by the use of the directionalmicro-explosive instrument made by us , the once success ratio of micro-explosion was93.2% and tl~o rmulb of treatment were satisfactory. . Considering the density of theblood vesselsiD the human liver, limitation of space in the h~patic.ducb, the securiey andadaptation, we have designed two types of micro- explosives equipment called ZS device,electric initiation and nonelectric initiation to initiate explosion. The head diameter of thedevice ie 1.5-1.8 mm . It is applicable to all kinds of fiber endoscope by inserting ZSdevice under grossing eyes or TV set ."

Jan 1, 1993

By James Rowland, Marcia Harris, Richard Mainiero

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NO x ). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed.

Jan 1, 2007

By Ray Patterson

A planned modification to a cement kiln at the Holnam Portland Cement Plant near Florence, Colorado required the removal of a ring of cast-in-place (CIP) refractory lining. The CIP lining was approximately 14 inches wide, 12 inches thick and 38 feet in circumference.

Jan 1, 1999

By Doug Anderson

Two quantities, Peak Particle Velocity (PPV) and Scaled Distance (SD), have controlled aspects of many blasting projects and operations for a long time. Vibration criteria typically use both PPV and SD because they are simple to measure, and simple to calculate. Their use in regulations worldwide is fairly ubiquitous, in efforts to limit damage to structures in the neighborhood of a blasting operation. PPV and SD are also used to determine likely blast damage effects in mining operations.

Jan 1, 2018

By Douglas R. Burns

In New England, an area of the country where 3 ½" holes are considered large diameter,we are starting to experiment with 5" and 6" holes. The results are excellent in some areas and poor in others. The geology of rock is the major consideration to account for the blasting results.

Jan 1, 1997

By John C. Didlinger, John L. Didlinger

As we begin the pre-blast survey we need to decide on the number of holes needed for production and a detailed highwall inspection. The survey consists of checking the highwall and placement of barrier cones. At the Elmhurst Chicago Stone Company, Barbers Corner Plant, we use 18-24" orange highway type safety cones. These cones are easily noticed because of their high visibility color in all weather conditions and are placed approximately 20-25 feet from the face and approximately 50 feet apart along the highwall, then the area is checked for back break, under cut, over hang, surface filled area and clay area. This deposit is unique because of the number of clay filled areas and slip seams that meanders through the deposit plus a fault that runs North-Northwest and South-Southeast. This particular limestone deposit is overlaid with glacial sand and gravel and the top weathered stone wanders plus or minus 10 feet in 1400 feet.

Jan 1, 1996

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by using electronic detonators. The Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast fragmentation measured with the SPLIT image analysis system to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed, and the powder factor increased, to maximize fines. However, a growing number of studies have shown that the use of electronic detonators can lead to increased fragmentation and greater muckpile uniformity, providing an alternate means of increasing primary breakage by blasting. Unfortunately results in the literature rarely quantified the changes to the fragmentation distribution. The measured gyratory crusher fragmentation of 2,750,000t of ore was used to compare stockpiles constructed from shots using pyrotechnic detonators to those using Orica i-kon electronic detonators. In the first stage of the study, stockpiles shot using 25 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using the same inter-hole timing with electronic detonators. In the second stage of the study, stockpiles shot using 17 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using 8 ms inter-hole timing with electronic detonators. When electronic detonators were used with the inter-hole timing kept constant, fragmentation uniformity was slightly increased, but mean fragment size increased by 20%. When electronic detonators were used with faster inter-hole timing, fragmentation uniformity was slightly reduced, but mean fragment size decreased by 30%. Modeling was used to determine the SAG mill throughput which could be expected from this change in fragmentation to determine the pairs of pyrotechnic and electronic blast pattern geometries that would provide similar throughput. The economic benefit from the electronic detonator shots was calculated to assist in determining the optimum blast designs for their use.

Jan 1, 2010

By Michael Wieland

Delay blasting in underground coal generates shock waves and rifting forces that damage charges remaining in the blast pattern. Damaged charges detonate poorly, raise fume toxicity and reduce coal breakage. Such circumstances could be prevented by using explosives resistant to cross-hole interaction damage. The design of rugged explosives is fraught with contradictory requirements, but tradeoffs related to hard-particle size characteristics prove useful. Hard particles, related voids or trapped bubbles represent reaction nucleation centers which strongly influence the performance of coal mine explosives.

Jan 1, 1992

By Jerome S. Brower

Quadrex-L is a two component liquid explosive which was developed by J. S. Brower & Associates, Inc. to facilitate handling and shipping, and use in unique applications, while emphasizing safety. It may be advantageously used for all explosive applications. Quadrex-L can be introduced into a preinstalled container configuration and may be easily drained or flushed from these containers when necessary to do so. This characteristic can be effectively utilized to reduce the hazard period during assembly or disassembly operations.

Jan 1, 1975

By Paulo Couciero

Since explosives are the source of all energy used for rock blast fragmentation and heave, multidimensional effects in the detonation driving zone become essential to better describe the detonation process. In order to use the explosive as an energy source-information for more realist blasting performance simulations, a simple and effective modelling strategy is desirable. Facing this challenge, an engineering approach to two-dimensional unconfined non-ideal detonation is proposed. Based on the elliptical construction of the shock locus, the model combines the axial cylindrical stick Q1D solution with some additional limiting conditions to determine the sonic edge of the charge. For a given set of rate law parameters and velocity of detonation, a complete axial solution is firstly computed through the Q1D model. From this solution, a vital relationship between the axial shock curvature with the shock shape parameters can be stablished. Once this relationship is found, the problem simply reduces in finding the shock shape parameters subject to the sonic edge condition. As a result of this calculation, the corresponding charge diameter can be found. Consequently, the proposed model can map the diametereffect curve by relating the unconfined velocity of detonation with its corresponding diameter. Finally, because of its low computation cost, the proposed engineering approach can be also used for characterizing the rate law parameters by fitting to data from unconfined detonation experiments

Jan 1, 2019

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By R W. Thomas

"This paper explores the possibilities of generating radical improvements in the drihing costs andproductivity of blastholes through the efforts of integrated teams as opposed to traditionalcustomer/vendor relationships."

Jan 1, 1996

By G Alan Foster

Many complaints generated from blasting operations result from the marked human response to ground transmitted vibrations and air blast effects and so many authorities have considered the regulation of blasting in terms of human response rather than, as previously, in terms of preventing damage to structures.

Jan 1, 1981