Search Documents

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Robert Hopler

Of the common causes of the larger mine accidents, such as falls of roof and coal, gas and dust explosions, mine fires, and the misuse of explosives, all of which are often closely related, each must be studied and fought in a manner peculiar to itself. The last mentioned, the misuse of black powder and other explosives, is sometimes considered the least important of these causes of mine accidents; but its importance is much greater than the statistics indicate, for the reason that the misuse of explosives is the true cause of many of the fatal mine fires, gas or dust explosions, and falls of roof that are credited to other causes.

Jan 1, 2012

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By Charles Zdazinsky

Many blasting applications in the mining industry demand that the hard rock being blasted remains structurally competent. For example, pre-splitting is a common technique to reduce fracturing, and operators of dimension stone quarries use this blasting method to eliminate overbreak. When pre-split design parameters are not applied correctly, there will be a redistribution of stresses within the rock, resulting in Blast Induced Rock Damage (BID). Advances in geophysical technology are enabling blast technicians to monitor BID and then use the results to correctly design their blasts.

Jan 1, 2011

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By Carlos Campos Junior, Leonardo Soares Chaves, Raul Carretero Hoz, Renato Jacome Costa, Davi Bastos Martins de Oliveira

The Vale’s Serra Sul mine, also known as S11D project, is one of the world’s largest open pit iron ore mines, located in Brazil’s Amazon region. The mine produces around 90 Mt of high-quality iron ore annually. Its unique orebody enabled the S11D project to adopt a truckless mining system with In-Pit Crushing and Conveying (IPCCs) for ore exploitation and waste stripping. The IPCCs system requires crushing the waste, mainly composed by the jaspilite lithology, and is also conveyed to waste deposits several kilometers away from the mine. Due to Amazon’s environmental restrictions, the project was designed with preliminary geological knowledge, leading to the installation of primary crushers not designed for the hardest jaspilite, with uniaxial compressive strength (UCS) up to 500 MPa. This resulted in low waste crushing performance, affecting stripping ratio and threatening future production. A project was developed to improve the fragmentation of the jaspilite, allowing higher waste IPCC production, and reducing the risk to the production due to low performance of waste crushing and conveying. The first challenge was the independence of the geological and the geomechanical models, while only the geological model was considered in blast designs, the geomechanical model describes six waste groups of jaspilite classified according to their strength. A new geological model was then created to incorporate the geomechanical classification, allowing different blasting design according to the rock strength of the jaspilite. The blasting pattern on most compact jaspilite was reduced 27%, from 22m² to 16m² in 9 7/8” diameter holes, with a proposed theoretical reduction of 23% of the P80, from 326mm to 250mm. The second challenge was the implementation of the new design, as this pattern size and the high powder factor (2.9 kg/m3) were paradigms for such a large iron ore mine. The measured results have shown 25% reduction of the P80, the crushing rate was increased by 17% (230t/h), saving around $2.4 million annually in crushing and conveying system maintenance.

Jan 21, 2025

By C. Feliciano, M. Cavalcante

A large iron ore open pit mine in Brazil operates with reduced blast sizes, due to the imminence of red alerts in the rainy season and the proximity of plant and dam structures that demand control of the maximum load of fired explosives. Blasts are currently not allowed to remain loaded with explosives due to the risk of red alerts, limiting mine operations close to them. There is a need to increase the blast sizes, reducing the number of events required to obtain the planned mass and, consequently, the unproductive operating hours lost with mine evacuations. The WebGen™ wireless electronic initiation system is a technology for firing detonators via lowfrequency magnetic induction that propagates through the medium, without physical connection. A blast was carried out with 406 holes divided into 4 panels, aiming to validate the preloading technique with wireless detonators and its performance in safety and productivity. The absence of lead wires in the system eliminates the risk of interaction between vehicles and detonator cables in stemming and loading operations, which can result in unplanned detonation or misfire. By eliminating the need for a spotter, it reduces people's exposure to dust and the risk of human-machine interaction. Furthermore, it eliminates the risk of unplanned detonation caused by lightning strikes. The pre-loading technique with wireless detonators enables flexibility and efficiency in planning through temporary accesses over loaded areas. In the demonstration, driving over the loaded area was essential to avoid jams and excessive wear on equipment due to the narrow berm and very friable material. Another gain in productivity was optimizing operational stages, since detonators were programmed in parallel with loading, anticipating process stages, in addition to eliminating the need to connect detonators. Considering the average handling and savings in downtime due to the reduction of blasting events, a potential increase in movement of 49,000t (54,013 short tons) in 3 months was estimated, keeping the vibration results within the required limit. The trial with wireless detonators demonstrated the feasibility of carrying out blasts with preloaded panels, without restrictions on the number of panels or detonators, enabling vibration control, innovating mine planning and increasing safety and productivity

Jan 1, 2024

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By Rhys Baker, Tim O’Brien, Joshua M. Hoffman

This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms.

Feb 1, 2020

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017

By D. Lansburg

Electronic detonators are increasingly being used in today’s blasting in quarries, seismic, surface and underground mines. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, field programmability and digital safety means. Because of the prerequisite electrical communications between the electronic detonators and the blasting machine, the layout or hook-up of these detonators can play an important role in obtaining the communication fidelity.

Jan 1, 2011

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T), utilizes a probabilistic risk assessment (PRA) approach to explore the risks (anduncertainty) from chemical, biological, radiological and nuclear (CBRN) threat agents to the Homeland.This end-to-end risk methodology considers a broad range of hazards incorporating emergingtechnologies, available countermeasures and input from the Intelligence and Law Enforcementcommunities (IC/LE) to evaluate the acute risk to human health due to an attack on the U.S. homeland. The PRA generated output provides a mechanism to examine risk mitigation strategies, critical vulnerabilities, critical data and knowledge gaps and relative risk rankings of materials, targets, classes of compounds and scenarios."

Jan 1, 2017

By David Siskind, Mark Stagg

Vibrations from Dade County (Miami area) quarry blasting and structure responses were measured at 11 locations between February and April, 2000, and 10 homes were inspected to analyze the characteristics of their cracking and other damages. These results were combined with information collected by the County and other studies done in south Florida for a blasting impact assessment specific to this area. In addition over 40 quarry blasts in the nine-week monitoring period, about 800 measurements were available from previous monitoring in Dade and neighboring Broward counties. An overall worst-case analyses based on the highest individual amplitudes suggested that vibrations in some areas could have been as high as 0.35 in/s. While amplitudes in the study period were below this value, they were found to be relatively high for the distances and charge sizes. Attenuation with distance is less in Dade County than found elsewhere with quarries having to use scaled distances several times higher than similar sites in the north. Consequently, the vibrations are perceptible at very large distances.

Jan 1, 2001

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper develops a new Blastability Index to assess hole-to-hole fragmentation in bench blasting based on a new Rock Factor exclusively obtained from drill-monitoring data, that can provide an automatic assessment of rock structure, strength, and waste/ore, the effective energy factor of the explosive and the delay time per blasthole.

Feb 1, 2020