Search Documents

By Michael E. Curtis

This paper outlines a study performed to analyze the advantages of utilizing a blasting agent with a velocity of detonation that is 1.3 to 1.4 times the P-wave velocity of sedimentary shales and sandstones at a major Midwest coal operation.

Jan 1, 1997

By Steve Dillingham

The origin of the written blasting log or shot report can likely be traced back to the earliest annals of blasting and record keeping. These records were, for the most part, a way of checking inventory, production progress, or billing, and not necessarily designed with the intention of being used as a legal document in a court of law. As our litigious society has evolved to include far reaching regulatory requirements, however, the blasting log has developed to support and aid in the defense of the common blaster from blasting lawsuits by providing a comprehensive written report of his or her actions.

Jan 1, 2002

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"This document investigates a newly developed technique with the objective of improving terrain triangulation models (horizontal/sub-horizontal and vertical/sub-vertical terrains), mainly blast free faces. The algorithm uses multi-linear regressions to generate the best point cloud projection plane by applying the residues modulus minimization so as to create the finest 3D triangulation model. A change of base is required to create a new set of coordinate axis and generate completely new projection planes. The projection plane residue analysis is inferred in order to avoid or reduce the outlier points. The dataset is composed of 12 terrain models obtained from photogrammetry and a 3D Laser equipment thatgenerates georeferenced cloud points. This new technique is validated by the analysis of the obtainedcritical burden by the improvement of the general aspect view of the terrains and the capacity of outlier’s detection. The result and the quality of the algorithm demonstrates the improvement in the triangulation mesh, reducing errors in the calculation of over/under burden, free face volumes, cavities and, therefore, in the estimations of clearance/safety distances."

Jan 1, 2017

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Brad Bockey

Whether you are a driver, blaster, or are in charge of filing, you must recognize the importance associated with DOT-required recordkeeping. As various agencies become intertwined with rules governing the explosives industry, the records we produce must be as accurate as possible. The time is right for reviewing your paperwork process from start to finish.

Jan 1, 2011

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Ron J. Elliott, Corry Coumans

The following is a detailed description of the blasting procedures used in the successful demolition of the Stave River bridge, Mission, British Columbia, Canada. This highway bridge spans a highly sensitive salmon-spawning river. Demolition of the bridge took place in a high liability situation in close proximity to sensitive structures. The new highway bridge carrying an exposed 150mm diameter gas line was located only 1.5 meters away. The bridge piers were blasted only seven meters from overhead power lines. Control of blast vibration, flyrock, and underwater overpressure was critical to the success of the operation. Electrical sequential blasting was used to ensure that blast vibration on the new bridge structure was kept below 50mm per second.

Jan 1, 1998

By Park Yun-Seok, Jung Seung-Won, Hwang Nam-Sun, Song Jin-hyuk, Kim Young-ho

This study proposes a new blasting vibration estimation formula that reflects the vibration reduction characteristics of electronic detonators, which are not considered in the current MOLIT blasting vibration estimation formula. Test blasts were conducted across six types of Korean open-pit blasting designs. The results of the test blasts showed that the K value for electronic detonators decreased by approximately 30% compared to electric detonators. Predicted Peak Particle Velocity (PPV) analysis indicated a reduction effect ranging from 30% to 31% across various types. By incorporating this reduction in the K value into the MOLIT blasting vibration estimation formula (K=200), a new electronic detonator blasting vibration estimation formula (K=140) was proposed. Using this new formula, the blasting damage range (R) was calculated under various vibration limits to evaluate constructability improvement. On average, the R value for electronic detonators decreased by about 17%, with significant reductions of around 41% observed for TYPE I under certain vibration limits. In conclusion, the adoption of electronic detonators in open-pit blasting operations improves blasting efficiency, reduces economic costs, and significantly enhances constructability. Electronic detonators have demonstrated superior performance in minimizing damage to safety facilities compared to traditional electric detonators, thereby proving their practicality and effectiveness in blasting operations.

Jan 21, 2025

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By Dale S. Preece

A new three dimensional (3D) mechanistic model of fragmentation, called the Fracture Density Model (FDM) is used to simulate full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. The model uses several computational mechanics algorithms to simulate the effect of blasting in different rock types

Feb 1, 2020

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By I. Petrovsky

Presence of the ground water, especially flowing water, causes limitations in the type of the explosives, which can be used for the blasting development in the open cats and quarries. This presents really big problem in Russia, because more than 70% of the blasting holes are wet and filled by flowing water. The waterproof explosives need to be used in these conditions, which increases the cost of the blasting development. So the search of the methods to remove the water from the blasting hole and to prevent direct contact of the explosive material with the water is important. It will give possibility to use nonwaterproof explosives (such as ANFO) and decrease the cost of the blasting development.

Jan 1, 2003

By Gene Baker

A new Safety Library Publication (SLP), SLP-27, which is titled “Security in Manufacturing, Transportation, Storage and Use of Commercial Explosives” was recently released by the Institute of Makers of Explosives (IME). SLP-27 makes recommendations for both general security and enhanced security at explosives sites when security risk levels, declared by the Department of Homeland Security (DHS) using its Advisory System, have temporarily increased.

Jan 1, 2006