Search Documents

By Rustu S. Kalyoncu

Nonoxide ceramics with improved high-temperature properties could substitute for high-temperature alloys and reduce toe Nation's dependence on imports of Cr, Co, Ni, and Mn. To meet this objective, the Bureau of Mines conducted research to synthesize u1trafine reactive boron nitride (BN) powders BN powders were prepared at temperatures ranging from -75? to 750? C. Low-temperature reactions (-75? to 200? C) between boron halides and N compounds led to formation of e1emento-organic compounds that were thermally decomposed to u1trafine (approximately 100-to 150-A particle size) reactive BN powders. BN powders were also prepared through the reaction of a 10w-me1tinginorganic B compound (boric acid, borax) with an organic N compound (carbimide and thiocarbimide) in N2 and/or ammonia (NH3) atmospheres at temperatures between 500? and 750? C.

Jan 1, 1986

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth's crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers' dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

By Bruce Rock

A continuous mining machine was redesigned for the installation of an integrated illumination system. The illumination system was designed by first calculating the theoretical number of luminaires required to meet the Federal Illumination Standards. Luminaires initially were placed using isointensity diagrams. A darkroom was used for "fine tuning" and demonstrating that the system met the illumination requirements. The luminaire mounts were installed on a machine underground. The performance of this illumination system was monitored in the working environment of an operating coal mine. Design changes were made as necessary during this evaluation period to improve the system.

Jan 1, 1979

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By Leonard Obert

This report describes a gage which, when used with my procedure for producing strain relief, will measure the resulting borehole deformation, From the borehole deformation the magnitude and direction of the principal stresses in a plane normal to the axis of the borehole can be calculated. The design considerations, mechanical construction, sensitivity, and stability of the gage are discussed. INTRODUCTION During the past two decades an increasing mount of consideration has been given to the problem of measuring and evaluating stress in rock around underground openings. Several investigators have made theoretical and model studies of the stress and (or) strain concentrations around simulated mine openings or in structural members, such as mine pillars or immediate roof. Other investigators have developed gages for directly or indirectly measuring stress or strain, and a number of reports present the results of measurements made with these gages. Because various methods and instruments have been developed, factors involved in this type of measurement will be briefly considered.

Jan 1, 1962

MR. RIGG: Gentlemen, I would like to welcome you all to the symposium this morning. My name is Jack Rigg, and I m a special assistant to Hollis Dole, Assistant Secretary of the Interior for Mineral Resources. Hollis is not in town this morning, and I am here to pinch-hit for him. The first order of business this morning is remarks by the Honorable Russell Train, Under Secretary of the Department of Interior. Mr. Train. MR. TRAIN: Thank you, Mr. Rigg. Lest you think that Hollis Dole is not interested in this symposium, let me just say that fie is flying back from Australia just to be here. He is heading up a United States delegation in Australia meeting on resource problems in the Pacific. And I believe he will be here about noon.

Jan 1, 1970

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, increased in 1993. The increase in the value of tripoli production was the result of an increase in total production. Special silica stone experienced an increase in unit value but decrease in the quantity produced. Garnet showed a 19 % decrease in quantity and an 8 % decrease in value. Staurolite increased about 51 % in the quantity produced and 136 % in value compared with those of 1992. Staurolite's significant increase in value of production resulted from a 56 % increase in the unit value. The fused aluminum oxide industry showed an 8 % decrease in the quantity produced and a 13 % decrease in the value of production. The silicon carbide industry saw an 11 % decrease in the quantity produced and an 8 % decrease in the value of production. Combined, the industries decreased 9 % in quantity and 11 % in value compared with those of 1992.

Jan 1, 1993

By James E. Hill

Tremendous improvements in mining technology have been witnessed during the past 100 years. For example, before 1860 all blastholes were drilled manually and blasting was done with low-energy black-powder. During the 1860's both the pneumatic rock drill and high-energy dynamite were introduced, ushering in an era of mining mechanization that has steadily progressed since that time. Today, with the rapid implementation of the latest advances in communication science, mining technology is moving into a new era that goes beyond mechanization as such. Transistors, transducers, scanners, telemetry, and the like, all terms largely derived from the new communication sciences, add up to what is popularly know as automation-the communication of machine with machine. Automation is now playing an important role in selected parts of the mining process, such as hoisting, hydraulic roof supports, and underground surface locomotive haulage and belt conveyor systems. But this year marked the first attempt to auto-mate the total mining process with the commencement of production at the British National Coal Boards Bevercotes mine. If this full-scale experiment proves successful, it could lead towards other fully automated mines in both Britain and other parts of the world. This decade, there-fore, could be considered the one that provided the foundation for the mines of the future.

Jan 1, 1966

By Charles C. Boley

High-volatile A bituminous coal from the Allen mine, Las Animas County, Colo., blended with char produced from the same coal yielded accept-able metallurgical coke in a 500-lb movable-wall test oven. Nineteen experimental runs were carried out using several concentration levels of two different chars, 5.6 and 19.6 percent volatile matter, produced by entrainment carbonization of the base coal. With the higher-volatile char, an acceptable coke was produced at a 22.5-percent concentration; the lower-volatile char did not produce an acceptable coke at the concentrations investigated.

Jan 1, 1972

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940