Search Documents

By M. D. Schlesinger

As part of the development of processes for producing synthetic fuels from coal, the Bureau of Mines prepared a special jet fuel in a pilot plant for evaluation by the Air Force. This jet fuel had all the required physical properties, including the important specifications of high heating value and high density. However, the finished fuel did not pass the stability test specified by the Air Force and conducted by the Southwest Research Institute in a high-temperature research coker. The cause for this instability is being investigated because pure compounds of the type identified in this fuel are known to be stable. The tar acid oil used was a 230° to 300° C. fraction of low-temperature tar obtained by carbonization of a West Virginia bituminous coal in the pilot plant of the Consolidation Coal Co. Both the desulfurization at 400° C. and saturation at 300" C. were done in the vapor phase at 2,500 p.s.i.g. After catalytic treatment and distillation the final jet fuel had a boiling range of 194° to 247° C., a net heating value of 18,420 B.t.u./lb. and a specific gravity of 0.8463 60° F./60° F. It also had u pour point below -62° C., and at 0° C. its viscosity was 4.5 cs. The oil was virtually all bicyclic, 41 pct. noncondensed and 56 pct. condensed.

Jan 1, 1961

By Charles W. Merrill

The U .S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Charles W. Merrill

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By C. J. Wilhelm, John M. Devine, Ludwig Schmidt

"Steel tanks often corrode rapidly in oil fields where the Gas produced with crude contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion.Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no carious corrosive action. These uses indicated that aluminum tanks,be equally effective in counter- acting hydrogen sulphide corrosion. Consequently, in the spring of 1920, an all-aluminum stock tank of 500 barrels capacity and a ""composite"" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co, in Crane County, Tex. These tanks were under observation for one year, the toot being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Reel Co. The results of this preliminary test sustained the belief that aluminum is highly resistance to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the quantities o highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the aluminum Co. that additional tests be made to include production conditions in large quantities of brine would be handled, for pact experience had shown that aluminum often is susceptible to the corrosive action of brines."

Apr 1, 1931

By R. V. Ramani, K. V. K. Prasad, M. Swaminathan

"INTRODUCTIONMine ventilation planning is an engineering design process requiring a substantial amount of qualitative knowledge obtained through experience. A concept for a knowledge-based ventilation expert system was developed by Ramani and Prasad (1987).1 11 An expert system based on the above scheme was conceived with the motivation of providing a tool to facilitate decision making for ventilation engineers in the context of computer assisted ventilation planning. Options for the implementation of the system were then examined and several commercial, personal computer (PC) based shells assessed toward this end. The options considered, the evaluation criteria and procedure arc discussed in Prasad ·and Ramani, (1989).Cll Following the above study, a scheme was developed to represent the components of the expert system.<3> Evaluation of several commercial shells indicated that there was none available which permitted interfacing with a large external algorithmic program. It was therefore decided to develop the KBS in LISP and custom build the necessary interfacing routines to ""hook out• to the network analysis program (NAP). Due to this choice of development strategy, the computer implementation aspects of the KBS arc important as all the interfacing components had to be developed with the basic tools offered by LISP.In this paper, the implementation of the knowledge based system (KBS), in terms of its component, the interfaces among the various components of the KBS and between the KBS and the user arc described. The ventilation KBS consists of an AES (analysis expert system), an IES (interpretation expert system)' and an algorithmic NAP (network analy5is program). The AES analyzes the input to the NAP considering the legal 5tipulations governing the various mine ventilation network parameters and principles of good ventilation, helping the ventilation engineer develop and represent represent the problem for solution by the NAP. The IES diagnoses the output from the NAP in terms of the critical parameters in the context of the given problem. Thi5 loop is continued till a satisfactory salution is obtained. The implementational details of the AES, the IES and the approaches to the validation of the expert system arc also discussed."

Jan 1, 1990

GLOSSARY Acid- and toxic-forming materials. Rock or coal layers containing significant amounts of pyrite or other minerals which, if exposed by coal mining, will cause acid or toxic drainage to occur when acted upon by air and water. Add mine drainage. Any water with a pH less s than 6.0 draining from a coal mine. Water is often orange-colored because of the presence of oxidized iron. Adit. An underground mine entry at sites where coal seams are exposed at ground level. Apple core. A complete hilltop (360°) left exposed by not backfilling the highwall. Approximate original contour. The surface configuration achieved by backfilling and grading the mined area so that be reclaimed land closely resembles the general pre-mining surface configuration and blends into and complements the drainage pattern of the surrounding terrain. Area mining. A surface mining method that is carried on in level to gently rolling topography on relatively large tracts of land. Active area mine pits may be several miles long. Arid and semiarid regions. Lands, generally west t of We 100% meridian, where water use by native vegetation equals or exceeds that supplied by natural precipitation, and rainfall is insufficient to support agriculture. Annual precipitation is normally 20 inches or less. Auger mining. A mining technique often used by surface mine operators when the overburden becomes too for the coal to be mined economically using traditional surface mining methods. Large-diameter (usually 2&apos;-4&apos;) horizontal holes are drilled as much as 300 feet into We vertical Me of the coal bed by an auger. Like a bit used for boring holes in wood, coal augers consist of a cutting head with a screw-like extension. As the auger turns, the head breaks up the coal and the screw carries it back into a conveyor that loads it directly into a truck. Backfilling. The operation of refilling an excavation using material removed during the mining process. Bench. The level or flat working area at the base of the highwall that is excavated between the exposed coal seam and the original surface of the ground. Bucket wheel excavator. A continuous-digging machine that uses a rotating vertical wheel with buckets for large-scale stripping and excavating. Cessation Order. Order to cease mining issued to a coal operator by the regulatory authority due to severity of violations, Contemporaneous reclamation. Restoration of mined land that occurs as soon as practical after coal removal. Contour mining. A mining method commonly used in eastern mountainous topography where coal is removed in a narrow strip around the hillside. The extent of the cut into the hillside is determined by the depth of overburden at the highwall compared with the thickness of the coal seam. Daylighting. A term used to describe a surface mining procedure that exposes abandoned underground coal mine workings to enable removal of the remaining coal. Daylighting is followed by land reclamation. Dragline. An excavating machine, usually used in large, flat areas, that drags a bucket (which holds up to 220 cubic yards of material) toward the machine by cables, loads it with spoil, and then hoists it wit a boom up to 350 feet long, allowing the machine to excavate wide benches by depositing the spoil hundreds of feet away from the highwall. Grading. The process of smoothing the disturbed areas of the mine site, after the coal is removed, to closely approximate the pre¬mining terrain. Haul road. Any road constructed, improved, maintained, or used by mine operators and located within the permit area. Head-of-hollow fill. See "valley rill." Highwall. The cliff-like excavated face of exposed overburden and coal in a surface mine. Hydroseeding. Planting of seed mixed in a water medium. Water, mulch, lime, fertilizer, and seed are blended and sprayed onto regarded soil.

Jan 1, 1992

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By D. W. Richardson

This Bureau of Mines publication provides the enthalpy of formation of malachite [Cua(COs)(OH)2] as determined by hydrochloric acid solution calorimetry. At 298.15 K the enthalpy of formation from the component oxides is -15.l0±0.30 kcal/mole and from the elements, -251.9±0.5 kcal/mole.

Jan 1, 1974

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

In this issue, the Bureau of Mines announces the availability of the latest of its Mineral Perspectives series: ?MP-4, mineral Industry of Western Europe." This publication describes the mineral industries of 19 Western European countries. For readers unfamiliar with this new series, reproduced below and on the two succeeding pages, is the section dealing with the mineral industries of France. Information regarding acquisition of this publication is found inside the back cover of this issue. FRANCE France is a moderately important producer of minerals, including iron ore, coal, potash, fluorspar, and uranium. In addition, France is a significant processor of imported minerals, chiefly for its own consumption. In general, it has exportable surpluses only of a little iron ore (low-grade ore exported to Luxembourg) and some nonmetallics.

Jan 1, 1977

By Roy F. Abernethy

This publication by the Federal Bureau of Mines contains the free-swelling indexes for 2,812 samples of coal received from January 26, 1948, to July 15, 1957, and the Hardgrove grindability indexes for 2,339 samples of coal received from June 23, 1947, to July 15, 1957. These data consist of the origin of the sample, bed name, and analysis. Summaries show the high, low, and average values for each bed. The free-swelling index is a relative measure of the caking properties of a coal when burned on a grate, and the Hardgrove grindability index is used to estimate the relative ease of grinding coals. Development and standardization of these test procedures were at a much later date than those for the more familiar tests, such as proximate and ultimate analyses and calorific value determinations. The newer tests are valuable in supplying supplemental information, particularly for assisting in evaluating coals used in certain types of combustion processes.4/ Data from such tests are important to designers of burning equipment, operating engineers, and purchasing agents. Data from these newer tests are scarce and scattered through a number of publications. Special projects were started to determine the free-swelling and grindability indexes, in addition to the regular analyses on the tipple samples collected by Bureau engineers. Since the start of these special projects, all the coal fields of commercial importance have been adequately covered in the sampling program.

Jan 1, 1961

By Harry W. Campbell

In 1984 and 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the Meadow Valley Range Wilderness Study Area (NV-050-156) in order to evaluate its identified mineral resources. The study area is located in Clark and Lincoln Counties, NV, about 50 miles northeast of Las Vegas, NV. The Johnston and Fitchett prospect, in the northern part of the study area, has more than 3 million tons of marginal perlite reserves suitable for many commercial uses. A preliminary mining feasibility estimate suggests perlite could be profitably mined from the study area; however, it is unlikely these perlite deposits will be developed in the foreseeable future because of unfavorable market conditions. Zeolite minerals occur in alteration zones adjacent to perlite deposits at the Johnston and Fitchett prospect, but high quality material is closer to potential markets. A metalliferous black shale unit containing 800,000 tons of subeconomic resources may extend into the study area at the Bradshaw vanadium prospect on the northwest boundary. Limestone, stone, sand, and gravel occurrences are wide-spread, but other suitable deposits in the region are more accessible to potential markets. Seven prospects in and near the study area were examined. The entire study area is leased for oil and gas exploration. A group of perlite placer claims covering more than 480 acres was located in the 1940&apos;s in the northern part of the study area. A small group of lode claims was located in the mid 1950&apos;s in the southwest part of the study area. No mining claims are currently (1985) held inside the study area. No mineral production is known from within the study area.

Jan 1, 1987

By E. D. Gardner

This paper is a progress report on the study of mining methods and costs in the western United States and summarizes that part of the work pertaining to the undercut block-caving method of mining. Ore is mined on a large scale exclusively by the undercut block-caving method at the following six mines in the western United States: The Morenci branch of the Phelps Dodge Corporation, Morenci, Ariz.; the Ray mines of the Nevada Consolidated Copper Co. at Ray, Ariz.; the Inspiration Consolidated Copper Co. at Inspiration, Ariz.; the Miamo Copper Co. at Miami, Ariz.; the Ruth mine of the Nevada Consolidated Copper Co. at Ruth, Nev.; and the Consolidated Coppermines Corporation at Kimberly, Nev. The undercut block-caving method is also used at the mine of the Andes Copper Mining Co. at Potrerillos, Chile.

Jan 1, 1930

By C. E. Brechtel

This project describes the design and testing of large face ventilation systems for oil shale mining. A design data base was generated by reviewing general industry practice, oil shale industry planning, and technical literature. Conceptual designs for seven different systems were developed and evaluated for suitability. A large, free-standing, jet fan and reversible fan with rigid duct were selected for fabrication and testing. The two systems were field tested in a dead-end heading 55 ft wide by 30 ft high and 320 ft long. System performance was optimized using measurements of air flow direction and air velocity. Total system performance was then measured using SF6 tracer gas released to simulate blast fumes, hot diesel exhaust, methane layering and methane from a blasted muckpile. Field testing indicated that both systems delivered similar performance. The jet fan offered some clear advantages because of its mobility, ease of oper-ation and lower power requirement. It also offered some functional advantages in ventilating for methane because of it high average velocity.

Jan 1, 1985

A general description of investigative work conducted by the Bureau of Mines at the, Missouri Valley. manganese deposits and leading to tonnage and grade estimates has been given in Report of Investigations 4375, part 1 of a three-part report of work done between July 1945 and August 1947. Basic factual information from which tonnage and grade estimates were drawn was derived through the drilling sampling of 238 large-diameter bucket-drill holes in 11 widely separated areas. Drilling areas were selected after careful reconnaissance, mapping, and consideration of earlier work done on the deposits by the Bureau of Mines, State agencies, and private organizations and individuals. Stratigraphic studies permitted extending the results compiled within the drilling; areas to outcrop and lightly covered manganiferous zones between an beyond drilling areas. The locations of drilling areas, drilling sections, and individual drill hues are shown on illustrations in part 1 f this report. The individual drill holes, aside from providing the basic information for tonnage and grade estimates, disclosed features affecting any future plan As exploitation. It in particularly significant that a large part of the visible outcrops is faulted end otherwise complicated by slides that give a false impression of the thickness, vertical location, and even the existence of manganese-bearing zones.

Jan 1, 1949

By N. S. Dalal, Xianglin Shi

"The mechanism of vanadium(V) V ) toxicity is still not fully understood in spite of extensive current effort (1-3). The presence of a vanadium(V) V ) -dependent NAD ( P )H oxidase in cell membranes suggests that at least one of the pathways involves oxidation of NAD(P)H (1-3). Considerable effort has therefore been devoted to finding the mechanism of NAD ( P ) H-oxidation by va¬nadium( V ) (1-19). Recently Liochev and Fridovich (4, 16) provided a critical review of vanadium( V) -stimulated NAD (P )H oxidation by plasma membranes. They out¬lined a mechanism in which vanadium(V) V )-stimulated oxidation of NAD ( P )H by biomembranes involves an O2 - initiated free radical chain reaction (4 ). While the above may be the major pathway for the vanadium-me¬diated NAD (P )H oxidation in membrane-related sys¬tems, some recent results suggest that in the presence of NADPH the flavoenzyme glutathione reductase can function as a vanadium(V) V ) reductase (18). Because of the significance of this result in relationship to the mech¬anism of vanadium( V) metabolism and the novelty of the metal-reductase behavior of a flavoenzyme, we have car¬ried out additional studies on one-electron reduction of vanadium( V) by two other, related flavoenzymes: lipoyl dehydrogenase and ferredoxin-NADPH oxidoreductase. These two enzymes were selected because they are known to catalyze a one-electron reduction of Cr ( VI ) (19-21 ), which is isoelectronic with vanadium( V ).The present study also reports on the generation of hydroxyl ( • OH) radicals in the vanadium( V) -flavoen-zyme redox system without exogenous H2O2. The • OH study was undertaken because • OH radicals are known to be generated in reactions of vanadium( IV) with H2O2 (17,18,22-27). For example, Piette and co-workers (17, 22) have studied effects of vanadium(IV) IV ) on lipid per-oxidation and NADPH oxidation and suggested that va-nadium( IV) -induced • OH radical formation may play an important role in vanadium( V) toxicity. Carmichael (25, 26) investigated the reaction between a RNA /VO 2' complex and H2O2 with a view to probe the possible re-lationship between vanadium( IV) -mediated • OH radical generation and DNA damage. He has suggested that in this reaction the • OH radical adds to the C (5) carbon of uracil, causing nucleotide damage, similar to what occurs in the nucleotide /Fe2+ / H2O2 reaction (28) and in y-irradiated aqueous solutions of nucleic acids (29 ). To our knowledge, however, there is as yet no report on ·OH radical generation in any reaction involving the reduction of vanadium ( V) by a well-characterized enzyme, without exogenous H20 2 • The present study provides evidence that ·OH radicals can form in a flavoenzyme-mediated reduction of vanadium( V) to vanadium( IV) and that this process involves also the reduction of molecular oxygen ( 0 2 ) to H20 2 • The H20 2 thus generated reacts with vanadium( IV) to produce ·OH radical, in analogy with the Fenton reaction ( Fe2 + + H20 2 - Fe3 + + OH- + ·OH)."

Mar 1, 1992

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

By Robert N. Roby

The Hornsilver lead-zinc property was examined by the Bureau in 1942 and again in 1944. A project was started on the property in April 1946 and completed in January 1947. Silver was first discovered in this district in 1883, and while complete production records are not available, it is known that a substantial tonnage of high-grade silver ore was shipped before 1887. All of the ore was mined from surface or near-surface workings. When the high-grade oxidized ore was exhausted, the district became inactive and remained so until the 1920&apos;s. In 1928 and 1929 some activity was shown in the district, but the Hornsilver mine was not reopened until November 1937. Between 1939 and 1946, the mine produced about 16,000 tons of ore of 531 ounces of gold, 283 ounces of silver, over a million pounds of load, and nerdy 2 million pounds of zinc. The property is now controlled by the Era Mining & Development Co., which has acquired the Last Chance and Ella groups of claims, in addition to the Hornsilver mine.

Jan 1, 1948